• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회 논문집(I)
• /
• pp.353-358
• /
• 1998

The strain localization is a discontinuous phenomenon that addresses the formation of jumps of the field variables across a singularity surface. It has become widely accepted that the localization may occur as the result of discontinuous bifurcation which corresponds to the loss of ellipticity of the governing differential equations for elasto-plastic continua. In this paper, condition for strain localization in concrete based on bifurcation theory is studied and localization tensor analysis algorithm is employed to determine the directions of localization of deformations in concrete. By applying a plasticity model of concrete into the algorithm, localization analysis is performed concrete under uniaxial tension, pure shear and uniaxial compression.

• Computers and Concrete
• /
• 제31권1호
• /
• pp.33-52
• /
• 2023

This paper proposes and validates the extension of two models, previously formulated for the evaluation of the shear strength of reinforced concrete members with un-corroded reinforcements, to the case of beams with corroded stirrups. These extended models are based on the plasticity theory (this model has been proposed in the past by one of the authors) and on the simplified modified compression field theory. The response of these models is compared with that of the compression chord capacity model, which has recently been embedded with modifications that simulate the effects of steel corrosion. These latter modifications are first discussed and then introduced into the other two models. An existing database of slender and non-slender beams tested in laboratory by other researchers is revised and improved. Finally, all the considered models are applied to the selected specimens and a comparison is drawn between the shear strength resulting from the considered models and the shear strength resulting from the laboratory tests. The effects of corrosion on some important parameters of the ultimate shear response of the reinforced concrete beams are also discussed.

• 대한기계학회논문집B
• /
• 제21권11호
• /
• pp.1413-1421
• /
• 1997

A new control method to alleviate the impulsive noise at the exit of high-speed railway tunnel was applied to the compression wave at the entrance of the tunnel. This method uses the interaction phenomenon of unsteady expansion wave and unsteady compression wave. Unsteady expansion wave was assumed to be made instantaneously by the simple theory of shock tube. Total Variation Diminishing method was employed to solve the axisymmetric unsteady compressible flow field with a specified compression wave. Numerical results show that the maximum pressure gradient of the propagating compression wave decreases with increase of the wave length of the unsteady expansion wave. It is found that the impulsive noise reduction can be obtained when the unsteady expansion wave with a large wave length is emitted just before the train enters the tunnel. The present results give the possibility to reduce the impulsive noise at the exit of tunnel.

• 소성∙가공
• /
• 제22권7호
• /
• pp.394-400
• /
• 2013

Microforming is a very efficient and economical technology to fabricate very small metallic parts in various applications. In order to extend the use of this forming technology for the production of microparts, the size effect, which occurs with the reduction of part size and affects the forming process significantly, must be thoroughly investigated. In this study, the tribological size effect in microforming was studied using modeling and scaled ring compression experiments. A micro-scale friction approach based on the slip-line field theory and lubricant pocket model was used to understand the friction mechanism and explain the tribological size effect. Ring compression tests were performed to analyze the interfacial friction condition from the deformation characteristics of the ring specimens. In addition, finite element analysis results were utilized to quantitatively determine the size-dependent frictional behavior of materials in various process conditions. By comparing theoretical results and experimental measurements for different size factors, the accuracy and reliability of the model were verified.

• 전산구조공학
• /
• 제9권1호
• /
• pp.151-159
• /
• 1996

구조용 콘크리트의 비선형 거동을 예측하기 위하여, 압축강도 연화현상, 거시적 및 회전균열모델등의 내용을 포함하고 있는 압축장 응력장 이론(CFT)에 근거한 유한요소법이 개발/제시되었다. 또한, 이와 관련하여 CFT가 암시하는 탄젠트 및 세칸트 재료강성이 반복계산해법의 관점에서 정의/논의되었다. 최종적으로 계산상의 효율성 증대 및 최대하중 이후의 거동 포착에 주안점을 두어 초기재료 강성을 채택한 변위증분법 논리 및 빠른 수렴을 위한 Over-Relaxtion방법이 Isoparametric계의 8-Node요소에 포함/유도되었다. 이와 같이하여 제시된 비선형 해석 프로그램 NASCOM은 응력 혼돈지역에 위치하는 콘크리트 평면요소의 하중 지지능력, 탄성범위 이후의 변형 특성, 균열양상 및 보강근의 항복범위등의 예측을 가능하게 하였다. NASCOM의 제한된 검증을 위하여, Cervenka의 판넬 시험결과에 대한 하중지지능력 및 변형이력등을 예측한 결과가 전체적인 의미에서 실험결과와 상응하는 일치를 나타내었다.

• Steel and Composite Structures
• /
• 제44권6호
• /
• pp.883-898
• /
• 2022

A hollow-core partially-encased composite beam, named HPEC beam, is investigated in this paper. HPEC beam comprises I-beam, longitudinal reinforcement, stirrup, foam formwork, and cementitious grout. The foam formwork is located on both sides of the web, and cementitious grout is cast within the steel flange. To investigate the shear performance of HPEC beams, static loading tests of six HPEC beams and three control beams were conducted. The shear span ratio and the number of studs on the shear behavior of the HPECspecimens were studied. The failure mechanism was studied by analyzing the curves of shear force versus both deflection and strain. Based on the shear span ratio (𝜆), two typical shear failure modes were observed: shear compression failure when 1.6 ≤ 𝜆 ≤ 2; and diagonal compression failure when 𝜆 ≤ 1.15. Shear studs welded on the flange can significantly increase the shear capacity and integrity of HPEC beams. Flange welded shear studs are suggested. Based on the deformation coordination theory and superposition method, combined with the simplified modified compression field model and the Truss-arch model, Modified Deformation Coordination Truss-arch (M.D.C.T.) model was proposed. Compared with the shear capacity from YB9038-2006 and JGJ138-2016, the calculation results from M.D.C.T. model could provide reasonable predictions.

• Advances in nano research
• /
• 제7권6호
• /
• pp.405-417
• /
• 2019

This research is devoted to study post-buckling analysis of functionally graded carbon nanotubes reinforced composite (FG-CNTRC) micro plate with cut out subjected to magnetic field and resting on elastic medium. The basic formulation of plate is based on first order shear deformation theory (FSDT) and the material properties of FG-CNTRCs are presumed to be changed through the thickness direction, and are assumed based on rule of mixture; moreover, nonlocal Eringen's theory is applied to consider the size-dependent effect. It is considered that the system is embedded in elastic medium and subjected to longitudinal magnetic field. Energy approach, domain decomposition and Rayleigh-Ritz methods in conjunction with Newton-Raphson iterative technique are employed to trace the post-buckling paths of FG-CNTRC micro cut out plate. The influence of some important parameters such as small scale effect, cut out dimension, different types of FG distributions of CNTs, volume fraction of CNTs, aspect ratio of plate, magnitude of magnetic field, elastic medium and biaxial load on the post-buckling behavior of system are calculated. With respect to results, it is concluded that the aspect ratio and length of square cut out have negative effect on post-buckling response of micro composite plate. Furthermore, existence of CNTs in system causes improvement in the post-buckling behavior of plate and different distributions of CNTs in plate have diverse response. Meanwhile, nonlocal parameter and biaxial compression load on the plate has negative effect on post-buckling response. In addition, imposing magnetic field increases the post-buckling load of the microstructure.

• Structural Engineering and Mechanics
• /
• 제16권2호
• /
• pp.115-126
• /
• 2003

A novel finite element model based on the incremental endochronic theory with the effect of temperature was developed in this study to explore the deformed behaviors of a flexible pavement material. Three mesh systems and two loading steps were used in the calculation process for a specimen of three-dimensional circular cylinder. Computational results in the case of an uni-axial compression test for temperatures at $20^{\circ}C$ and at $40^{\circ}C$ were compared with available experimental measurements to verify the ability of developing numerical scheme. The isotropic response and the deviatoric response due to the thermal effect were presented from deformations in different profiles and displacement plots for the entire specimen. The characteristics of changing asphalt concrete material under a specified loading condition might be seen clearly from the numerical results, and might provide an useful information in the field of road engineering.

• 한국지반공학회논문집
• /
• 제28권1호
• /
• pp.55-66
• /
• 2012

본 논문에서는 쏘일네일링 공법, 앵커 공법, 또한 이 두공법의 장점을 결합한 하이브리드 공법의 하중전이 메커니즘에 대한 연구를 수행하였다. 하이브리드 공법은 철근과 PC강연선을 보강재로 하며, 프리스트레스를 가함으로써 능동적인 주면마찰력 양상을 유도하고자 한다. 본 논문에서는 주면마찰력 산정 이론과 하중전이 이론을 바탕으로 각 공법의 하중전이 메커니즘을 파악하였다. 또한 현장인발시험을 실시하여 측정된 계측결과의 분석 및 하중전이 이론과의 비교 검토를 통해서 하이브리드 공법의 하중전이 메커니즘을 규명하였다. 쏘일네일링 공법은 인발거동 시 전면에서부터 선단으로 인장력이 전이되는 양상을 보이는 반면, 앵커 공법은 내하체가 위치한 선단에서 프리스트레스를 가함에 따라 선단에서 전면으로 압축력이 전이된다. 이 두 공법을 결합시킨 하이브리드 공법은 프리스트레스를 가할 때에는 앵커공법과 같이 선단에서 압축력이 발생하지만 동시인발 시에는 선단에서는 압축력이 전면에서는 인장력이 발생하게 된다. 따라서 하이브리드 공법의 하중전이 메커니즘은 쏘일네일링의 거동과 앵커의 거동이 모두 나타난다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.540-543
• /
• 2004

In this study, the validity of the grid softened strut-tie model method suggested for concrete member analysis is examined through the ultimate strength evaluation of the reinforced concrete beams. The evaluated results of ultimate strength by the grid softened strut-tie model method were compared with those by the ACI 318-02 and the modified compression field theory, and European codes.