• Geomechanics and Engineering
• /
• 제16권6호
• /
• pp.599-608
• /
• 2018

This study investigates the feasibility of adopting the results of the UC (unconfined compression) test to assess the total cohesion of the unsaturated soil. A series of laboratory tests were conducted on samples of unsaturated lateritic soils of northern Taiwan. Specifically, the unconfined compression test was combined with the pressure plate test to obtain the unconfined compression strength and its matric suction of the samples. Soil samples were first compacted at designated water content and then subjected to the wetting process for saturation and the subsequent drying process to its target suction using the apparatus developed by the authors. The correlations among the matric suction, the unconfined compression strength and the total cohesion were studied. As a result, a simplified method to estimate the total cohesion using the unconfined compressive strength is suggested. The calculated results compare reasonably with the unsaturated triaxial test results. Current results show good performance; however, further study is warranted.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.315-320
• /
• 2003

Two different strength types of plain concrete plate specimens (200$\times$200$\times$60mm) were tested under different biaxial load combinations. The specimens were subjected to biaxial combinations covering the three regions of compression-compression, compression-tension, and tension-tension. The loading platens with Teflon pads were used to reduce a confining effect in boundary surface between the concrete specimen and the solid platen. The principal deformations in the specimens were recorded, and the failure modes along with each stress ratio were examined. Based on the strength data, the failure envelops were developed for each type of plain concrete. The biaxial stress-strain responses of concrete plate specimens for three biaxial loading regions were also plotted. The test data indicated that the strength of concrete under biaxial compression ($f_2 / f_1$$_1$=-1/-1) is about 17 percent larger than under uniaxial compression.

• 콘크리트학회논문집
• /
• 제21권4호
• /
• pp.401-408
• /
• 2009

초고강도콘크리트의 개발에 따라 철근 압축이음에 대한 연구 필요성이 높아지고 있다. 40여년 전의 연구를 바탕으로 한 현재의 압축이음 설계기준으로는 향상된 강도를 제대로 활용할 수 없으며, 특히 압축이음길이가 인장이음 길이보다 길어지는 기현상(奇現象)이 발생되어 실무의 혼란을 초래하기도 한다. 이러한 현상은 현행 설계기준에서 콘크 리트 강도와 횡보강근의 영향을 고려하지 않기 때문이다. 본 연구에서는 51개 실험체의 결과를 바탕으로 40부터 70MPa 까지 콘크리트에 대한 압축이음길이 설계식을 제안하였다. 실험 결과를 통해 도출된 압축이음의 영향 인자들을 분석하 여 이음강도식의 기본형을 만들었다. 실험 결과에 대한 비선형 회귀분석을 통해 압축이음강도 평가식을 마련하고, 5% 분위수 개념을 통해 설계기준이음강도를 설정하고 압축이음길이 설계식을 도출하였다. 이 연구에서 제안된 압축이음길 이 설계식을 이용하여 고강도콘크리트에서 압축이음길이가 인장이음길이보다 길어지는 이상 현상을 해소할 수 있다. 더 불어 제안된 압축이음길이 설계식은 통계적 기법에 기반을 두어 재료강도와 동일한 수준의 신뢰성을 확보할 수 있다.

• 한국건축시공학회지
• /
• 제4권2호
• /
• pp.113-118
• /
• 2004

This study is a basic experiment on quality management of the compression strength of high strength concrete, aiming. at quality management of high strength mass concrete by giving the temperature hysteresis of the mass test pieces to managerial test pieces. Different from ordinary concrete, high strength concrete generally shows the temperature high rising caused by hydration heat inside the concrete. It is known that, in mass concrete, thermal stress occurs due to the difference in temperature between the inside and the outside, which causes a significant difference in compression strength between structure beams and managerial test pieces. It is also reported that there is a large difference between the compression strength of cylindrical managerial test pieces of standard underwater curing and the strength of structure beam concrete. Thus, this study made concrete test pieces in an optimal mix ratio for each strength level, and also created thermal insulation curing box and managerial test pieces. Then it carried out comparative analysis in relation to core strength and suggested equipment and a technique that can control the strength of high strength concrete mass more conveniently and accurately.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.410-413
• /
• 2008

In this study, we compare the mechanical properties of forged and machined bushings for an excavator track chain. The manufacturing process is explained in detail together with the procedure of making the specimens. The longitudinal tensile strength and elongation and the radial ring compression strength are measured for this comparison. It has been shown that the forged is much better than the machined with regard to both longitudinal tensile strength and radial ring compression strength but that both are the same in terms of longitudinal elongation.

• Structural Engineering and Mechanics
• /
• 제12권1호
• /
• pp.71-84
• /
• 2001

The objective of this paper is to develop a simplified method that could predict the strength of concrete filled steel tube (CFT) columns applicable to high strength material under combined axial compression and flexure. The simplified method for determining the strength of CFT columns is based on the interaction curve of the section approached by a polygonal connection of the points. These points are determined by using symmetrical properties of the CFT section. For each point, a simple equation is proposed to determine the strength of the slender columns under compression and flexure. The simple equation was adjusted with results of elasto-plastic analysis results. Validation of the simplified method is undertaken by comparison with data from the test conducted at Kyushu University. These results confirm the fact that the simplified method could accurately and reliably predict the strength of CFT columns under combined axial compression and flexure.

• 한국해양공학회지
• /
• 제15권1호
• /
• pp.85-91
• /
• 2001

A study for the structural strength analysis on the doubler plate subjected biaxial in-plane compression and shear load has been performed through the systematic evaluation process. In order to estimate the proper static strength of the doubler plate, non-linear elasto-plastic analysis is introduced. Gap element modeling for contact effect between the main plate and the doubler is prepared and nonlinear analysis procedures are illustrated based on MSC/N4W. In addition, some design guides are suggested through the consideration of several important effects such as corrosion of main plate, doubler width, doubler length and doubler thickness. Finally, theses result are compared with a developed design formula based on the buckling strength and general trends. The design guides, according to the variation of design parameters are discussed.

• 한국포장학회지
• /
• 제7권1호
• /
• pp.16-20
• /
• 2001

In order to optimize designing process of corrugated fiberboard boxes for agricultural products, first of all, compression strength of each liner were experimentally evaluated on the various conditions of relative humidity and analyzed by liner regression analysis. At the 66 percents of relative humidity, IK(imported kraft liner) liner board lost little of its compression strength compared to others. At the relative humidity 93 percents, KA liner board lost its compression strength only 40 percents while SK liner board lost up to 56 percents. From the result of prediction modeling of ring crush strength in various humidity conditions, R square values were ranged from 0.59 to 0.97. At 56 percents of RH or below, R square values were relatively low, but at 66 percents of RH or higher, the values were 0.85 or higher. The significance values were lower than 0.001 at every RH condition. Level of significance of experimented values was about 80 percents of predicted values and R square values were between 0.89 to 0.95.

• 터널과지하공간
• /
• 제7권2호
• /
• pp.91-99
• /
• 1997

To stabilize the energy price, the more storage facilities of energy are required and among the storage methods of LPG and LNG, the method of storage at low temperature under normal confining pressure is considered. It is needed to understand the mechanical and thermal characteristics of rock under temperature variation so that the behaviors of rock can be predicted. In this paper, the variation of the rock charateristics of the Hwangdeung granite and the Boryung sandstone is studied at low temperature. The mechanical characteristics of rock under low temperatures are that as temperature decreased, unaxial compression strength and Young's modulus increased for Hwangdeung granite; strength and Young's modulus in wet condition were greater than those in dry condition. In the case of Boryung sandstone, as temperature decreases unaxial compression strength and Young's modulus increase but decrease below -10$0^{\circ}C$ in dry condition and below -16$0^{\circ}C$ in wet condtion. The mechanical characteristics of rock after cooling to previous temperature and thawing are that uniaxial compression strength and Young's modulus decrease as temperature decreases. Uniaxial compression strength and Young's modulus in wet conditon decrease more than those in dry condition. Brazilian tension strength decreases as temperature decreases.

• 한국강구조학회 논문집
• /
• 제13권3호
• /
• pp.223-232
• /
• 2001

본 연구에서는 높은 축력을 받는 기둥재에 사용 가능성이 큰 고장력 용접구조용 압연강재인 SM570의 압축좌굴내력을 평가하기 위해서 중심압축실험을 실시하였다. 단 주압축 실험결과 강구조 계산규준이 정하고 있는 판폭두께비의 제한치를 만족시키는 기둥부재의 최대내력은 국부좌굴에 의해 결정되며, 판폭두께비의 제한치를 만족시키지는 못하는 경우에는 최대내력이 도달하기 전에 국부좌굴에 의해서 급격히 저하하였다. 또한 압축 좌굴내력이 SM570 강재의 설계기준값인 $4.1tonf/cm^2$보다 높게 나타났다.