• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.634-637
• /
• 2008

Ground source heat pumps are clean, energy-efficient and environment-friendly systems cooling and heating. Although the initial cost of ground source heat pump system is higher than that of air source heat pump, it is now widely accepted as an economical system since the installation cost can be returned within an short period of time due to its high efficiency. In the present study, performances of ground source compound hybrid heat pump system applied to a large community building are simulated. The system design and operation process appropriate for the surrounding circumstance guarantee the high benefit of the heat pump system applied to a large community building. If among several renewable energy sources, ground, river, sea, waste water source are chosen as available alternative energies are combined, COP of the system can be increased largely and hybrid heat pump system can reduced the fuel cost.

• 한국정밀공학회지
• /
• 제21권10호
• /
• pp.162-169
• /
• 2004

High temperature uniaxial compression tests in the alpha single phase region were carried out on the Ti -43mo1%Al intermetallic compound, in order to obtain oriented lamellar microstructure. The compression deformation temperatures and strain rates are from 1573k to 1623k and 1.0x10$^{-4}$ s to 5.0x10$^{-3}$ s, respectively. Fully lamellar microstructure was observed after the uniaxial compression deformation in a single phase region followed by cooling to room temperature. Lamellar colony diameter depended on strain rates and test temperatures. The diameter varied between 8601m and 300fm. Stress-strain curve showed a work softening and the size of lamellar colony diameter varied depending on peak stresses. This shows the occurrence of dynamic recrystallization. Texture measurements after the uniaxial compression deformation, showed the development of fiber during dynamic recrystallization. It is seen that the area for the maximum pole density existed in 35 degrees away from the compression plane. The texture sharpens with a decrease in strain rate

• Annals of Clinical Neurophysiology
• /
• 제8권2호
• /
• pp.125-134
• /
• 2006

Among the various physiological factors that affect nerve conduction velocity (NCV), temperature is the most important. Because the influence of temperature is the most important source of error. It is known from animal experiments that conduction is eventually completely blocked at low temperatures, the myelinated A fibers being the first affected and the thin fibers of group C the last. Many studies showed that the NCV decreases linearly with lowering temperature within the physiological range. The distal motor latency increased by $0.2msec/^{\circ}C$ drop in temperature between $25^{\circ}C$and $35^{\circ}C$ in the median, ulnar and peroneal nerves. The temperature affect the neuromuscular transmission; The miniature endplate potential (MEPP) and endplate potential (EPP) are increase with increasing temperature. In myasthenia gravis, the reduction in the decremental response is observed following cooling. The lowering temperature make increase the amplitude of sensory compound action potential; make enlarge the surface area of compound muscle action potential with very little increase in amplitude; make diminish the fibrillation potential and increase the myotonia in needle electromyography (EMG). Because of these findings mentioned above, the skin temperature should be routinely monitored and controlled during nerve conduction tests and needle EMG and should be taken into account when interpreting the findings.

• Current Applied Physics
• /
• 제18권11호
• /
• pp.1205-1211
• /
• 2018

The frustrated magnet has been regarded as a system that could be a promising host material for the quantum spin liquid (QSL). However, it is difficult to determine the spin configuration and the corresponding mechanism in this system, because of its geometrical frustration (i.e., crystal structure and symmetry). Herein, we systematically investigate one of the geometrically frustrated magnets, the $TbB_4$ compound. Using resonant soft x-ray scattering (RSXS), we explored its spin configuration, as well as Tb's quadrupole. Comprehensive evaluations of the temperature and photon energy/polarization dependences of the RSXS signals reveal the mechanism of spin reorientation upon cooling down, which is the sophisticated interplay between the Tb spin and the crystal symmetry rather than its orbit (quadrupole). Our results and their implications would further shed a light on the search for possible realization of QSL.

• Bulletin of the Korean Chemical Society
• /
• 제11권3호
• /
• pp.209-214
• /
• 1990

A series of compounds consisting of 4'-oxybenzylidene-4-n-butylaniline, a mesogen, and a p-substituted phenoxyterephthaloyl structure a non-mesogen, interconnected through a central hexamethylene spacer were synthesized and their thermal behavior and liquid crystallinity were studied. p-Substituents included in this study are H, Cl, CN, $NO_2,\;n-C_4H_9O$ and phenyl groups. The compounds having phenyl and $n-C_4H_9O$ substituents are enantiotropic and form smectic-A(SA) and nematic (N) phases. The compound with $NO_2$ substituent is monotropic and forms only a nematic phase on heating the solid, whereas it forms nematic as well as $S_A$ phases on cooling the isotropic liquid. The rest compounds were found to be non-liquid crystalline. This is in great contrast to the fact that the monomesogenic model compound 4'-n-hexyloxybenzylidine-4-n-butylaniline forms $S_B,\;S_C,\;S_A$ and N phases enantiotropically.

• 대한기계학회논문집B
• /
• 제21권11호
• /
• pp.1485-1495
• /
• 1997

The present study investigates heat/mass transfer around film cooling jets and circular cylinders to compare the characteristics of each other. Experiments are conducted to obtain the detailed heat/mass transfer coefficients of flat plate with injections through an array of holes and for flows around an array of protruding circular cylinders using the naphthalene sublimation technique. The inclination angles of cylinders are set to the same ones of jets; a, the angle between the jet and the surface is fixed at 30 deg. through the whole experiments and .betha., the angle between the projection of the jet on the surface and the direction of main stream is adjusted to 0 deg., 45 deg. and 90 deg. to investigate the effect of variation of injection angles. The influence of blowing rates of jets and those of cylinder length to diameter ratios are also investigated. The results indicate that the increase of angle .betha. influences the spanwise uniformity of heat/mass transfer remarkably for both jets and cylinders, but that variation of cylinder length to diameter ratios has weaker effects on heat/mass transfer coefficients than that of blowing rates.

• 한국수정란이식학회지
• /
• 제4권1호
• /
• pp.1-13
• /
• 1989

This paper reviews the most important steps that have generated consistent progress in principles and developmental progress of embryo cryopreservation, and also study on freezing procedure and its application by conventional method and current improved method for freezing procedure and its appilcation of embryo cryopreservation in farm animals. Four were of particular interest: 1.The transport of water across the ccli membrane (zona pellucida) during freezing and thawing accordinglyplays a role in determing whether the celi survives. This movement of water is controlied mainly by extracellular phase changes and by the nature and concentration of any cryoprotective agent present. Therates of cooling, freezing and warming, and the intervals over which they are applied are further decisi've factors in determining whether a cryopreservation procedure allows survival after thawing. 2.The first successful deep freezing experiments with sheep morula and blastocysts during the seventies were based on the early procedures used for mouse embryos.Current research during the eighties is developed with the aim of simplifying and improving current procedures such as one-step dilution and rapid or ultra-rapid cooling by using the model of laboratory animals. 3.The conventional method for the embryo cryopreservation is described. An alternative to this method which may result in high survival and also in reducing of the freezing and thawing time is done by combing a permeable cryoprotectant such as glycerol, DMSO or propanediol and a non-permeable compound such as sucrose, trehalose, raffinose or lactose. 4.Finally a different approach to the preservation of embryos, named vitrification, is introduced. This procedure depends upon the ability of concentrated solutions of cryoprotective agents such as glycerol and propanediol to supercool to very low temperature (-196$^{\circ}C$) during rapid cooling before solidifying without formation of ice. However, more complete data are necessary for successful vitrification of blastocysts.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1999년도 PROCEEDINGS OF 99 INTERNATIONAL CONFERENCE OF THE KACG AND 6TH KOREA·JAPAN EMG SYMPOSIUM (ELECTRONIC MATERIALS GROWTH SYMPOSIUM), HANYANG UNIVERSITY, SEOUL, 06월 09일 JUNE 1999
• /
• pp.419-431
• /
• 1999

InP, III-V binary compound semiconductor, single crystal was grown by VGF (vertical gradient freeze) method using quartz ampoule and its electrical optical properties were investigated. Phosphorous powders were put in the bottom of quartz ampoule and Indium metal changed in conical quartz crucible hat was attached at the upper side position inside the quartz ampoule. It was vacuous under the pressure of 10-5 Torr and sealed up. In metal in the quartz crucible was melted at 1070$^{\circ}C$ and phophorous sublimated at 450$^{\circ}C$, there after it was diffused in In melt and so InP composition was formed. By cooling the InP composition melt (2$^{\circ}C$∼5$^{\circ}C$/hr of cooling rate) in range of 1070$^{\circ}C$∼900$^{\circ}C$, InP crystal was grown. the grown InP single crystals were investigated by X-ray analysis and polarized optical microscopy. Electrical properties of them were measured by Van der Pauw method. At the cooling rate of 2$^{\circ}C$/hr, its direction was (111), quality of the ingot ws better upper side of the ingot than lower. It was found that the InP crystals were n-type semiconductor and the carrier concentration, electron mobility and relative resistivity were 1015∼1016/㎤, 2x103∼3x104$\textrm{cm}^2$/Vsec and 2x10-1∼2x10-3Ωcm in the range of 150K∼300K, respectively.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1746-1750
• /
• 2004

The objective of this study is to investigate the effect of supercooling repression on the clathrate compound by adding additives. For this purpose, phase change temperature and supercooling were measured when additives added to TMA30wt% clathrate for heat source temperature of $-6^{\circ}C$. The experimental results show that the phase change temperature with the chloroform of 0.1wt% is higher by $0.3^{\circ}C$ than TMA30wt% and the supercooling with the surfactant 0.1wt% is reduced by $9.2^{\circ}C$.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.635-640
• /
• 1996

A thermo-elastic system in the production machine has highly nonlinear dynamic characteristics. In general, the finite element method is utilized for accurate analysis. However, it requires large computing time. Thus, thermo-elastic systems are usuallymodeled as electric and fluid system using lumped para,eter. In this paper. we propose the bondgraph model and transient simulation methodology of thermo-elastic system in consideration of various boundary and joint contact conditions. Consequently, the proposed method ensures a possibility of its on-line compensation about undesirable phenomena by using real time estimate process and electronic cooling device for thermal appropriate behavior. Thermo-elastic model consisting of bush and shaft including contact condition is presented.