• Journal of Mechanical Science and Technology
• /
• v.16 no.9
• /
• pp.1137-1146
• /
• 2002

An experiment has been conducted on the flow and heat transfer characteristics of film coolant injected from a row of five holes with compound angle orientations of 35$^{\circ}$ inclination angle and 45$^{\circ}$ orientation angle. The Reynolds number based on the mainstream velocity and injection hole diameter 3.58${\times}$10$^4$. Three-dimensional velocity, film cooling effectiveness and heat transfer coefficient data are presented at three different mass flux ratios of 0.5, 1.0 and 2.0. Flow entrainment has been found between the vortices generated by adjacent injectants. The injectant with compound angle orientation entrains not only the mainstream boundary layer flow but also the adjacent injectant. Because of the flow entrainment, the injectant. With compound angle orientation is characterized by a single vortex while two bound vortices are usually observed in the case of simple angle injection. The strength of the secondary flow depends strongly on the mass flux ratio, which shows significant influence on the film cooling effectiveness and heat transfer coefficient.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.5
• /
• pp.577-586
• /
• 1999

Two problems with jet injection through the cylindrical film cooling hole are 1) penetration of jet into mainstream rather than covering the surface at high blowing rates and 2) nonuniformity of the film cooling effectiveness in the lateral direction. Compound angle injection is employed to reduce those two problems. Compound angle injection increases the film cooling effectiveness and spreads more widely. However, there is still lift off at high blowing rates. Shaped film cooling hole is a possible means to reduce those two problems. Film cooling with the shaped hole is investigated in this study experimentally. Film cooling hole used in present study is a shaped hole with conically enlarged exit and Inlet-to-exit area ratio is 2.55. Naphthalene sublimation method has been employed to study the local heat/mass transfer coefficient and film cooling effectiveness for compound injection angles and various blowing rates around the shaped film cooling hole. Enlarged hole exit area reduces the momentum of the jet at the hole exit and prevents the penetration of injected jet into the mainstream effectively. Hence, higher and more uniform film cooling effectiveness values are obtained even at relatively high blowing rates and the film cooling jet spreads more widely with the shaped film cooling hole. And the injected jet protects the surface effectively at low blowing rates and spreads more widely with the compound angle injections than the axial injection.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1215-1222
• /
• 1989

본 논문의 목적은 공기 유동장내에 가스분류의 거동을 조사하고 실용 가스 기관의 설계시에 필요한 기초적 데이타를 제공하고자 하는데 있다.본 연구와 관련 된 후래의 연구를 보면 자문등은 열선농도프로브를 사용하여 정상분류중의 농도측정을 행하였고, 분류내의 내부구조를 상세히 조사하였다. 특히, 종래에는 일정하게 보였 던 분류코아 부의 농도변동값의 경향을 구체적으로 나타내었다.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.4
• /
• pp.46-52
• /
• 1997

In this paper th use of compensation based on a combination of active plus reactive power at distribution model system is proposed. The basic voltage-power relationships for the linearized case on an infinite bus are used and the compensation angle is defined based on the voltage magnitude response to small power injection. Compensation is supplied at several locations, and the system is subjected to varying fault scenarios, with its response observed under different system conditions. As number of control issues for a storage-based active/reactive power compensator as a bus voltage regulator are explored to compare the effectiveness of active/reactive again reactive-only compensation.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.11
• /
• pp.1485-1495
• /
• 1997

The present study investigates heat/mass transfer around film cooling jets and circular cylinders to compare the characteristics of each other. Experiments are conducted to obtain the detailed heat/mass transfer coefficients of flat plate with injections through an array of holes and for flows around an array of protruding circular cylinders using the naphthalene sublimation technique. The inclination angles of cylinders are set to the same ones of jets; a, the angle between the jet and the surface is fixed at 30 deg. through the whole experiments and .betha., the angle between the projection of the jet on the surface and the direction of main stream is adjusted to 0 deg., 45 deg. and 90 deg. to investigate the effect of variation of injection angles. The influence of blowing rates of jets and those of cylinder length to diameter ratios are also investigated. The results indicate that the increase of angle .betha. influences the spanwise uniformity of heat/mass transfer remarkably for both jets and cylinders, but that variation of cylinder length to diameter ratios has weaker effects on heat/mass transfer coefficients than that of blowing rates.

• Archives of Plastic Surgery
• /
• v.32 no.3
• /
• pp.311-313
• /
• 2005

Generally, many Asian women tend to dislike the square jaw, as they believe it makes the face look wider, giving a stubborn and strong impression. Contouring of the mandible is therefore a relatively common aesthetic procedure among Asians. These days, the use of botulinum toxin for contouring of the lower face offer simple alternative to surgery. Motor point, which is the site over a muscle where its contraction may be elicited by a minimal intensity short duration electrical stimulus, is the optimal injection point of botulinum toxin. Study was undertaken to identify the location of motor point of the masseter muscle and the skin surface landmark. First, the thickest point of the masseter muscle was inspected through palpation and inspection by 3 different individual plastic surgeons and then compound muscle action potentials(CMAPs) of masseter muscle in 15 health volunteers were recorded using EMG. For the localization of the measured points, line between lateral canthus to the mandibular angle was used. Location of motor points were mapped to skin surface from lateral canthus in a percentage of the distance along the landmark line and in distance in millimeters. The clinical injection point was located at 71.69 percentile and 7.3 mm of the landmark line. The motor point test was located at 72.54 percentile and 7.1 mm of the landmark line. The depth of motor point was 16mm. There was no statistically significant difference between the clinical injection point and the motor point. We conclude that surface mapping of motor point of the masseter muscle would increase accessibility and accuracy in botulinum toxin injection for contouring of the lower face.

• Journal of the Korean Society of Safety
• /
• v.9 no.1
• /
• pp.100-109
• /
• 1994

In this study, it is investigated that the possibility of the numerical simulation for the incineration of the hazardous material, crbon tetrachloride($CCl_4$). A 3-dimensional numerical technology is applied for turbulent reacting flows of the full-scale Dow Chemical incinerator. The calculations are made by a CRAY-2S, super computer. The major parameters considered in this study are kiln revolution rate (rpm), filling ratio of the solid waste(f), burner Injection velocity and angle, and turbulent air jets for swirl. And the employed turbulent reaction model is the eddy break-up model which is a kind of fast chemistry model assuming general equilibrium and used for a premixed flame. The calculated flow fields are presented and discussed. 1) The presence of turbulent air nozzles for swirl gives rise to visible increase of the convective motion over the region of the solid waste. This implies the possibility to enhance the mixing of the waste with the surrounding all and thereby to reduce thermal and species stratification, which were reported in a large rotary kiln operation. 2) Considering that the location of the recirculation region has a strong relation with the heating rate of the solid waste, the control of the recirculation region by the burner injection angle Is quite desirable in the sense of the flexible design of the rotary kiln incinerator for a carbon tetrachloride. 3) Finally, it is found that the eddy break-up model Is not suitable for carbon tetrachloride($CCl_4$) because this model is not incorporated the flame inhibition trend due to the presence $CCl_4$compound.