• 한국강구조학회 논문집
• /
• 제19권4호
• /
• pp.413-423
• /
• 2007

기존의 층고절감형 합성보 시스템은 철골보의 웨브면에 바닥판을 삽입하여 시공하기 때문에 상대적으로 기존 합성보 형식과 비교하여 층고를 대폭적으로 줄일 수 있지만, 적용되는 철골보 춤이 제한되기 때문에 적용 가능한 스팬이 한정되어 있어 여러 가지 다양한 건축구조의 수요에 능동적으로 대처하기가 어려운 단점이 있다. 따라서, 본 연구에서는 기존의 층고절감형 합성보의 단점을 해결하기 위하여 합성보의 춤을 자유로이 조절할 수 있는 층고절감형 매입형 합성보를 개발하였다. 본 연구는 콘크리트에 매입된 강팡성형 철골보를 가지는 불완전 합성보의 휨거동에 관한 것이다. 총 5개의 실대형 실험체를 전단연결재 및 보강근의 사용유무, 슬래브 형식을 주요변수로 하여 실험을 수행하였다. 실험결과, 별도의 전단연결재를 설치하지 않은 실험체는 자체가 가지고 있는 기계적 화학적 부착응력으로 인해 $0.20{\sim}0.76N/mm^2$의 부착응력을 나타내었다.

• 전산구조공학
• /
• 제12권4호
• /
• pp.69-69
• /
• 1999

Design of Dangsan Steel Railway Bridge(a part of Seoul Subway Line NO. 2), which is supposed to be replaced after its 15years survice, was done, and the reconstruction has begun in Dec. 1997. The design include new superstruc-ture and bridge piers, retrofitting of the foun-dation, rail system, electric and signal, etc. In this paper, design of the structure is mainly summarized. The main span superstructure, across Han river, is composite section which is com-posed of steel box and reinforced concrete deck slab with 9 span continuous. The superstructure for the approaches is bottom througth type 2-cell steel box girder with steel floor system and concrete deck slab with 3 or 4 span continuous. The bridge piers was planned to be reconstructed based upon the result from the various investi-gations, while the foundation(cassion and pile foundation) was planned to be retrofitted. For superstructure erection, the method of combination of barge bent and heavy lifting and the launching truss method was investigated for the main span and approach spans, respectively.

• Earthquakes and Structures
• /
• 제18권3호
• /
• pp.367-377
• /
• 2020

Incremental dynamic analysis (IDA) widely uses for the collapse risk assessment procedures of buildings. In this study, an IDA-based collapse risk assessment methodology is proposed, which employs a novel approach for detecting the near-collapse (NC) limit state. The proposed approach uses the modal pushover analysis results to calculate the maximum inter-story drift ratio of the structure. This value, which is used as the upper-bound limit in the IDA process, depends on the structural characteristics and global seismic responses of the structure. In this paper, steel midrise intermediate moment resisting frames (IMRFs) have selected as case studies, and their collapse risk parameters are evaluated by the suggested methodology. The composite action of a concrete floor slab and steel beams, and the interaction between the infill walls and the frames could change the collapse mechanism of the structure. In this study, the influences of the metal deck floor and autoclaved aerated concrete (AAC) masonry infill walls with uniform distribution are investigated on the seismic collapse risk of the IMRFs using the proposed methodology. The results demonstrate that the suggested modified IDA method can accurately discover the near-collapse limit state. Also, this method leads to much fewer steps and lower calculation costs rather than the current IDA method. Moreover, the results show that the concrete slab and the AAC infill walls can change the collapse parameters of the structure and should be considered in the analytical modeling and the collapse assessment process of the steel mid-rise intermediate moment resisting frames.

• KIEAE Journal
• /
• 제7권6호
• /
• pp.113-118
• /
• 2007

The composite beam adopted in the study was designed to reduce the floor height as well as to embed the top flange of steel frame into the slab that will enable to avoid applying the fire-resistant coating and to unify the joint method with a steel frame-type. As the steel frame and bottom concrete of the beam is pre-fabricated at the factory it could reduce the overall schedule at the jobsite. Applying such composite beam system to the work is expected to provide the efficient and enhanced performance, given the current tendency of the building construction that tends to be getting higher, larger and dense. The study focused on combining the composite beam with various column systems in a bid to propose the details thereof. A desirable composite girder can be adopted depending on site conditions through the evaluation of various beam and jointing approaches. Among the column systems applied to the study are steel column, SRC column, RC-PC column and RC column. The ways of combining with the columns addressed in the study were categorized into the rigid joint, pin joint, steel frame joint and bracket type joint. Besides, the instruction for site fabrication of beam-column was added in an effort to help set up the site fabrication procedures.

• Steel and Composite Structures
• /
• 제26권4호
• /
• pp.485-499
• /
• 2018

In this paper, a hollow steel tube (HST) shear connector is proposed for use in a slim-floor system. The HST welded to a perforated steel beam web and embedded in concrete slab. A total of 10 push-out tests were conducted under static loading to investigate the mechanical behavior of the proposed HST connector. The variables were the shapes (circular, square and rectangular) and sizes of hollow steel tubes, and the compressive strength of the concrete. The failure mode was recorded as: concrete slab compressive failure under the steel tube and concrete tensile splitting failure, where no failure occurred in the HST. Test results show that the square shape HST in filled via concrete strength 40 MPa carried the highest shear load value, showing three times more than the reference specimens. It also recorded less slip behavior, and less compressive failure mode in concrete underneath the square hollow connector in comparison with the circular and rectangular HST connectors in both concrete strengths. The rectangular HST shows a 20% higher shear resistance with a longer width in the load direction in comparison with that in the smaller dimension. The energy absorption capacity values showed 23% and 18% improvements with the square HST rather than a headed shear stud when embedded in concrete strengths of 25 MPa and 40 MPa, respectively. Moreover, an analytical method was proposed and predicts the shear resistance of the HST shear connectors with a standard deviation of 0.14 considering the shape and size of the connectors.

• International Journal of Concrete Structures and Materials
• /
• 제7권1호
• /
• pp.51-59
• /
• 2013

The use of light-gauge steel framing in low-rise commercial and industrial building construction has experienced a significant increase in recent years. In such construction, the wall framing is an assembly of cold-formed steel (CFS) studs held between top and bottom CFS tracks. Current construction methods utilize heavy hot-rolled steel sections, such as steel angles or hollow structural section tubes, to transfer the load from the end seats of the floor joist and/or from the load-bearing wall studs of the stories above to the supporting load-bearing wall below. The use of hot rolled steel elements results in significant increase in construction cost and time. Such heavy steel elements would be unnecessary if the concrete slab thickening on top of the CFS wall can be made to act compositely with the CFS track. Composite action can be achieved by attaching stand-off screws to the track and encapsulating the screw shank in the deck concrete. A series of experimental studies were performed on full-scale test specimens representing concrete/CFS flexural elements under gravity loads. The studies were designed to investigate the structural performance of concrete/CFS simple beams and concrete/CFS continuous headers. The results indicate that concrete/CFS composite flexural elements are feasible and their structural behavior can be modeled with reasonable accuracy.

• Steel and Composite Structures
• /
• 제9권4호
• /
• pp.349-366
• /
• 2009

The composite slim beam has become popular throughout Europe in recent years and has also been used on some projects in China. With its steel section encased in a concrete slab, the steel-concrete composite slim beam can provide the floor construction with minimum depth and high fire resistance. However, the design method of the T-shape steel-concrete composite beam is no longer applicable to the composite slim beam with deep deck for its special construction, of which the present design models are not available but mainly depend on experiences. The elevation of the flexural stiffness and bending capacity of composite slim beams with deep deck is rather complicated, because the influences of many factors should be taken into account, such as the variable section dimensions, development of cracks and non-linear characteristics of concrete, etc. In this paper, experimental investigations have been conducted into the flexural behavior of two specimens of simply supported composite slim beam with deep deck. The emphases were laid on the bonding force on the interface between steel beam and concrete, the stress distribution of beam section, the flexural stiffness and bending capacity of the composite beams. Based on the experimental results, the reduction factor of equivalent stress distribution in concrete flange is suggested, and the calculation method of flexural stiffness and bending capacity of simply supported slim beams are proposed.

• 콘크리트학회논문집
• /
• 제26권6호
• /
• pp.741-749
• /
• 2014

프리스트레스트 중공(PHC) 슬래브는 장경간에 적합하도록 경량화된 효율적인 프리캐스트 부재이며, 국내 외에서 많이 사용되고 있다. 특히, 국내에서는 현장타설콘크리트와 같이 사용되는 합성슬래브 형태로 주로 적용되고 있다. 그러나, 압출성형방식으로 제작되는 PHC 슬래브 부재는 매우 낮은 슬럼프의 콘크리트로 제작되어 타설 직후에도 표면경도가 높기 때문에 계면의 거친면 처리 및 전단연결재 배치가 어려운 단점이 있다. 이 연구에서는 PHC slab 부재와 토핑콘크리트 사이의 합성성능을 고찰하기 위하여 다양한 계면상태를 변수로 직접전단실험을 수행하였으며, 기존 실험결과를 수집하여 국내 외 수평전단강도 설계기준을 평가하였다.

• 한국산학기술학회논문지
• /
• 제19권3호
• /
• pp.130-140
• /
• 2018

U형 강재보를 근간으로 콘크리트 슬래브와 합성을 위하여 A형의 덮개형 강재앵커를 검토하여 AU합성보를 연구하였다. 이는 노출형의 H형강 강재보에 비해 내부 평면의 자율성을 높일 수 있고 공기 단축과 더불어 층고 절감이 가능하며 튜브구조로서 내부에 콘크리틀 충전하여 휨 강도과 휨 강성를 높였다. 본 연구에서는 AU합성보의 휨실험을 통해 성능을 평가하였다. 실험 결과, 하중 초기에 선형적으로 하중이 증가하면서 콘크리트 슬래브의 파괴에 의해 최대 강도에 도달하고 최대 내력의 85% 이상을 발휘하며 연성적 거동을 하였다. 또한, 덮개형 강재앵커를 통해 합성효과를 발휘하였으며 모든 실험체가 최대 내력에 도달할 때까지 완전 합성거동으로 안정적이었다. 그리고 U형 단면의 강판 두께를 증가시켰을 경우에도 휨 강도와 휨 강성이 증가하였고, U형 단면의 하부에 고강도 강판을 용접 부착하였을 경우에도 성능이 개선되었다. AU합성보의 휨강도는 건축구조기준에 따라 제안된 휨 강도식을 적용할 수 있을 것으로 판단되었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제24권5호
• /
• pp.111-118
• /
• 2020

본 연구에 사용된 U-형 복합보는 슬래브는 철근콘크리트구조로 되어 있고, 슬래브를 지지해 주는 보는 철골구조와 철근콘크리트구조, 그리고 U-형 강판으로 이루어져 있다. U-형 복합보는 시공성이 우수하고 낮은 층고와 장경간이 가능하기 때문에 공작물 주차장으로 사용하기 위한 목적으로 개발되었다. 시공성 향상을 위해 U-형 복합보 단부는 규격화된 H형강으로 계획하여 기둥에 직접 접합시키고, 강재 물량을 감소시키기 위해 U-형 복합보의 중간 부분에는 H형강 대신 얇은 강판(t=6)을 사용하여 U자형 형태로 접은 U-형 강판으로 구성되어 있다. U형 강판이 위치하는 복합보 중앙부에는 보의 춤을 작게 계획함으로서 공작물 주차장의 제한 높이에 만족하도록 계획할 수 있다. 낮은 보의 춤은 층고 단축에는 유리하지만 휨성능에는 저해 요인이 되기 때문에 춤 변화에 따른 구조성능을 파악하는 것이 중요하다. 또한, U-형 복합보는 철골구조와 철근콘크리트구조 및 U-형 강판이 혼합되어 있기 때문에 일체성 확보가 구조성능을 확보하는데 큰 영향을 준다. 따라서 본 연구에서는 U-형 복합보의 춤을 변화에 따른 구조성능을 파악하기 위한 구조실험을 실시하였다. 실험체는 일반주차장용으로 계획된 실험체를 기준실험체로 하여 춤을 변화시킨 2개의 실험체를 포함하여 총 3개를 계획하였다. 실험결과 춤을 크게 계획한 실험체가 기준실험체보다 항복강도, 최대강도, 에너지 등 구조성능이 우수하게 나타났다.