• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1414-1417
• /
• 1996

The purpose of this study Is to research and develop $V_{6}O_{13}$ composite cathode for lithium thin film battery. $V_{6}O_{13}$ represents a class of cathode active material used in Li rechargeable batteries. In this study, we investigated cyclic voltammetry and charge/discharge characteristics of $V_6O_{13}$/SPE/Li cells. Cyclic voltammogram of $V_{6}O_{13}$/SPE/Li cell at scan rate 1mV/sec showed reduction peaks of 2.25V and 2.4V and oxidation peaks of 2.4V and 2.2V. The discharge curve of $V_{6}O_{13}$/SPE/Li cell showed 4 potential plateaus. The discharge capacity was decreased in the beginning of charge/discharge cycling. After 8th cycling, the discharge capacity was stable. The discharge capacity of 1st cycle and 15th cycle was 290mAh/g and 147mAh/g at $25^{\circ}C$, respectively.

• 전기화학회지
• /
• 제13권3호
• /
• pp.181-185
• /
• 2010

전도성 고분자로 널리 알려진 폴리아닐린과 액체전해질의 핵심 재료인 이온성 액체와의 복합체를 형성시키고 이들의 물리적, 전기화학적인 특성을 조사되었다. 이미다졸늄 이온성 액체 (1-methyl-3-propylimidazolium iodide, PMI-I)에 비전도성 폴리아닐린 (Emeraldine Base)을 30 wt%이상 첨가하였을 때 준고형화 현상이 나타났고, 이온성 액체의 이미다졸늄 양이온의 방향족 고리와 폴리아닐린의 벤족기와의 ${\pi}-{\pi}$ 자기상호조립에 의한 약한 도핑작용을 통해 섬유상 구조를 나타내었으며, 전도도의 변화율은 80%이상 유지하였다.

• 센서학회지
• /
• 제17권5호
• /
• pp.329-337
• /
• 2008

Simple, small and portable oxygen sensors were fabricated by tape casting technique. Yttria stabilized zirconia containing cordierite ceramics (YSZC) were used as a porous diffused layer of oxygen in pumping cell. Yttria stabilized zirconia (YSZ) solid electrolyte, YSZC porous diffusion layer and heater-patterned ceramic sheets were prepared by co- firing method. Limit current characteristics and the linear relationship of current to oxygen concentration were observed. Viscosity variation of the slurries both YSZ and YSZC showed a similar behavior, but micro pores in the fired sheet were increased with increasing of the cordierite amount. Molecular diffusion was dominated due to the formation of large pores in porous diffusion layer. The plateau range of limit current in porous-type oxygen sensor was narrow than the one of aperture-type oxygen sensor. However limit current curve was appeared in porous-type oxygen sensor even at the lower applied voltage. The plateau range of limit-current was widen as increasing the thickness of porous diffusion layer of the YSZ containing cordierite. Measuring temperature of $600{\sim}650^{\circ}C$ was recommended for limit-current oxygen sensor. Porous diffusion layer-type oxygen sensor showed faster response than the aperture-type one and was stable up to 30 days running without any crack at interface between the layers.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.56.1-56.1
• /
• 2009

The intermediate operating temperature of solid oxide fuel cells (IT-SOFCs) have achieved considerable importance in the area of power fabrication. This is because to improve materials compatibility, their long-term stability and cost saving potential. However, to conserve rational cell performance at reduced-temperature regime, cathode performance should be obtained without negotiating the internal resistance and the electrode kinetics of the cell. Recently, double perovskite structure cathodes have been studied with great attention as a potential material for IT-SOFCs. In this study, double-perovskite structured cathodes of $GdBaCoCuO_{5+\delta}$, $GdBaCo_{2/3}Cu_{2/3}Fe_{2/3}O_{5+\delta}$ compositions and $(1-x)GdBaCo_2O_{5+\delta}+xCe_{0.9}Gd_{0.1}O_{1.95}$ (x = 10, 20, 30 and 40 wt.%) composites were evaluated as the cathode for intermediate temperature solid oxide fuel cells(IT-SOFCs). Electrical conductivity of the cathodes were measured by DC 4-probe method, and the thermal expansion coefficient of each sample was measured up to $900^{\circ}C$ by a dilatometer study. Area specific resistances(ASR) of the $GdBaCo_{2/3}Cu_{2/3}Fe_{2/3}O_{5+\delta}$ cathode and 70 wt.% $GdBaCo_2O5+\delta$ + 30wt.% Ce0.9Gd0.1O1.95 composite cathode on CGO electrolyte substrate were analyzed using AC 3-probe impedance study. The obtained results demonstrate that double perovskite-based compositions are promising cathode materials for IT-SOFCs.

• 한국수소및신에너지학회논문집
• /
• 제17권2호
• /
• pp.149-157
• /
• 2006

Hydrogen as new energy sources is highly efficient and have very low environmental emissions. The proton exchange membrane fuel cell (PEMFC) is an emerging technology that can meet these demands. Therefore, the preparation of stable polymeric membranes with good proton conductivity and durability are very important for hydrogen production via water electrolysis with PEM at medium temperature above $80^{\circ}C$. Currently Nafion of Dupont and Aciflex of Asahi, etc., solid polymer electrolytes of perfluorosulfonic acid membrane, are the best performing commercially available polymer electrolytes. However, these membrane have several flaws including its high cost, and its limited operational temperature above $80^{\circ}C$. Because of this, significant research efforts have been devoted to the development of newer and cheaper membranes. In order to make up for the weak points and to improve the mechanical characteristics with cross -linking, acid-base complexes were prepared by the combination PSf-co-PPSS-$NH_2$ with PEEK-$SO_3H$. The results showed that the proton conductivity decreased in 17.6% and 40% but tensile strength increased in 78% and 98%, about $20.65\;{\times}\;10^6N/m^2$, in comparison with SBPSf/HPA and SPEEK/HPA complex membrane.

• 한국전기전자재료학회논문지
• /
• 제32권6호
• /
• pp.501-506
• /
• 2019

To overcome the limitations of the conventional Ni anode-supported SOFCs, various types of ceramic anodes have been studied. However, these ceramic anodes are difficult to commercialize because of their low cell performances and difficulty in manufacturing anode-support typed SOFCs. Therefore, in this study, to use these ceramic anodes and take advantage of anode-supported SOFC, which can minimize ohmic loss from the thin electrolyte, we fabricated cathode support-typed SOFC. The cathode-support of LSCF-YSZ was prepared by the acid treatment of conventional Ni-YSZ (Yttria-stabilized Zirconia) anode-support, followed by the infiltration of LSCF to YSZ scaffold. The composite of $La(Sr)Ti(Ni)O_3$ and $Ce(Mn,Fe)O_2$ was used as the ceramic anode. The fabricated cathode-supported button cell showed a relatively low power density of $0.207Wcm^{-2}$ at $850^{\circ}C$; however, it is expected to show better performance through the optimization of the infiltration rate and thickness of LSCF-YSZ cathode-support layer.

• 전기화학회지
• /
• 제2권4호
• /
• pp.202-208
• /
• 1999

[ $50/50 vol\%$ ] LSM-YSZ의 양극은 콜로이드 증착법에 의해 YSZ 전해질상에 증착하였다. 양극 특성은 주사전자현미경과 임피던스 분석기에 의해 고찰하였다. LSM-YSZ양극의 제조 조건에 따른 영향을 관찰하였으며, 그 영향에 대한 개선책이 고체산화물 연료전지의 성능향상을 위해 제시되었다. 임피던스에 대한 온도, YSZ전해질로의 양극 접착에 대한 표면 오염, 사용하는 Pt 페이스트, 미세구조에 대한 곡표면에 가해진 연무질 분사기술과 셀과 셀의 변동성에 대한 영향들은 각각 $900^{\circ}C$ 측정, YSZ표면 연마, 일단의 Pt페이스트 사용, 평편한 YSZ판의 사용과 일관된 절차와 기술의 사용에 의해 해결되었다. 이때 재현성 있는 임피던스 스펙트럼들이 향상된 셀을 사용함으로써 얻어졌고, $900^{\circ}C$에서 (공기)LSM-YSZ/YSZ/LSM-YSZ(공기) 셀에 대해 측정된 전형적인 임피던스 스펙트럼들은 2개의 불완전한 호로 구성되었다. 또한 LSM-YSZ 양극의 임피던스 특성은 촉매층, 양극 조성, 인가 전류 등과 같은 실험 조건들에 의해서도 영향을 받았다.

• Advances in materials Research
• /
• 제8권1호
• /
• pp.37-46
• /
• 2019

Electrochemical double layer capacitors (EDLCs) which are fabricated using carbon based electrodes have been emerging at an alarming rate to fulfill the energy demand in the present day world. Activated charcoal has been accepted as a very suitable candidate for electrodes but its cost is higher than natural graphite. Present study is about fabrication of EDLCs using composite electrodes with activated charcoal and Sri Lankan natural graphite as well as a gel polymer electrolyte which is identified as a suitable substitute for liquid electrolytes. Electrochemical Impedance Spectroscopy, Cyclic Voltammetry and Galvanostatic Charge Discharge test were done to evaluate the performance of the fabricated EDLCs. Amount of activated charcoal and natural graphite plays a noticeable role on the capacity. 50 graphite : 40 AC : 10 PVdF showed the optimum single electrode specific capacity value of 15 F/g. Capacity is determined by the cycling rate as well as the potential window within which cycling is being done. Continuous cycling resulted an average single electrode specific capacity variation of 48 F/g - 16 F/g. Capacity fading was higher at the beginning. Later, it dropped noticeably. Initial discharge capacity drop under Galvanostatic Charge Discharge test was slightly fast but reached near stable upon continuous charge discharge process. It can be concluded that initially some agitation is required to reach the maturity. However, the results can be considered as encouraging to initiate studies on EDLCs using Sri Lankan natural graphite.

• Composites Research
• /
• 제30권1호
• /
• pp.46-51
• /
• 2017

질량 및 부피 증가없이 전지와 구조물기능을 복합재에 결합시키는 구조전지 연구가 광범위하게 진행되고 있다. 탄소섬유 및 유리섬유를 하중지지 및 음극, 분리막 용도로 사용하고, 하중전달이 가능한 고체전해질을 모재로 쓰는 것이 현재 아이디어 이지만, 고체전해질이 두 성능을 충분히 만족시키지 못하는 수준이라 구조전지를 구현하지 못하고 있는 실정이다. 그래서, 본 연구는 유리섬유 분리막 및 액체전해질을 사용하여 하중지지 및 전지의 기능을 동시에 수행하는 실험을 구성하여 액체전해액을 사용한 구조전지의 가능성 및 전기적 물성 변화를 관찰하였다. 인장된 분리막은 안정성을 떨어트리는 영향을 미치는데, 이는 양극의 미세입자들이 늘어난 유리섬유의 틈새로 침투하는 것을 분리막이 막지 못하기 때문이라 예상하였고, 상용 분리막을 추가로 사용 하여 그 예상되는 원인을 확인해 보았다. 그리고, 이러한 구조전지 시스템을 구현하기 위해서는 유리섬유 특성의 연구와 전극과 분리막의 계면에 대한 연구가 필요하다.

• 전기화학회지
• /
• 제7권2호
• /
• pp.94-99
• /
• 2004

연료극 지지체 평관형 고체산화물 연료전지(SOFC)의 셀 전력밀도를 증가시키기 위하여 압출법에 의하여 제조하고 그 특성을 연구하였다. 연료극 지지체로써 Ni/YSZ($8mol\%$ yttria stabilized zirconia) cermet는 기공율 $50.6\%,\;0.23{\mu}m$의 기공크기를 나타내었다. 지지체에서의 Ni의 분포는 균일하였으며 전자전도 경로로써의 Ni의 연결성은 양호하였다. 지지체에 YSZ전해질과 복합 공기극층인 $LSM((La_{0.85}Sr_{0.15})_{0.9}MnO_3)/YSZ$ 복합층, LSM, LSCF $(La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3)$층이 슬러리 디핑법에 의하여 코팅 및 소결된 연료극 지지체식 평관형 고체산화물 연료전지 단위전지의 성능은 $800^{\circ}C$에서 $300mW/cm^2(0.6V,\;500mA/cm^2)$의 성능을 나타내었다. 임피던스 분석에 의하여 평관형 셀의 전기화학적 분극저항을 평가하고 연료측의 가습에 따라 분극저항이 감소되어 성능이 향상됨을 알 수 있었다 슬러리 디핑법으로 LSM이 코팅된 SUS430 금속연결재를 $Ar+10\%\;H_2$에서 소결하였으며, $750^{\circ}C$에서 면저항의 측정할 결과, 초기에는 $148m{\Omega}cm^2$를 나타내었으며, 450시간 경과 후에 $43m{\Omega}cm^2$의 낮은 면저항을 유지하였다. 반면에 동일한 조건으로 LSM이 코팅된 Fecralloy는 높은 면저항을 나타내었다.