• Progress in Medical Physics
• /
• v.19 no.1
• /
• pp.63-72
• /
• 2008

With recent advancement of the medical imaging systems and picture archiving and communication system (PACS), installation of digital radiography has been accelerated over past few years. Moreover, Computed Radiography (CR) which was well established for the foundation of digital x-ray imaging systems at low cost was widely used for clinical applications. This study analyzes imaging characteristics for two systems with different pixel sizes through the Modulation Transfer Function (MTF), Noise Power Spectrum (NPS) and Detective Quantum Efficiency (DQE). In addition, influence of radiation dose to the imaging characteristics was also measured by quantitative assessment. A standard beam quality RQA5 based on an international electro-technical commission (IEC) standard was used to perform the x-ray imaging studies. For the results, the spatial resolution based on MTF at 10% for Agfa CR system with I.P size of $8{\times}10$ inches and $14{\times}17$ inches was measured as 3.9 cycles/mm and 2.8 cycles/mm, respectively. The spatial resolution based on MTF at 10% for Fuji CR system with I.P size of $8{\times}10$ inches and $14{\times}17$ inches was measured as 3.4 cycles/mm and 3.2 cycles/mm, respectively. There was difference in the spatial resolution for $14{\times}17$ inches, although radiation dose does not effect to the MTF. The NPS of the Agfa CR system shows similar results for different pixel size between $100{\mu}m$ for $8{\times}10$ inch I.P and $150{\mu}m$ for $14{\times}17$ inch I.P. For both systems, the results show better NPS for increased radiation dose due to increasing number of photons. DQE of the Agfa CR system for $8{\times}10$ inch I.P and $14{\times}17$ inch I.P resulted in 11% and 8.8% at 1.5 cycles/mm, respectively. Both systems show that the higher level of radiation dose would lead to the worse DQE efficiency. Measuring DQE for multiple factors of imaging characteristics plays very important role in determining efficiency of equipment and reducing radiation dose for the patients. In conclusion, the results of this study could be used as a baseline to optimize imaging systems and their imaging characteristics by measuring MTF, NPS, and DQE for different level of radiation dose.

• Journal of The Korean Association For Science Education
• /
• v.37 no.2
• /
• pp.347-358
• /
• 2017

The purpose of this study is to research on the professional development of pre-service chemistry teachers in terms of personal practical knowledge(PPK), and draw a discussion for pre-chemistry teacher education. A reflective discussion through a Community of Practice(CoP) activity has been conducted with 5 pre-service chemistry teachers studying in a college of education located in Seoul. The analysis of the results reveals that 'Subject-matter knowledge' is leaning toward massive chemical contents, 'Curriculum knowledge' is below the level of selecting, analyzing, and applying curriculum materials. 'Instruction knowledge', especially the knowledge of chemistry experiment and research, is not enough to lead secondary students' scientific experiment. 'Milieu of school knowledge' is stunted in growth for the reason of communication-deficiency between a college of education and a community, and among education- related groups. 'Self-knowledge' has been diminished not only because there is a bad influence from college classmates not wanting to be a teacher, but also a lack of communication in the chemistry-education department which can make pre-teachers' belief strong. In conclusion, it is especially needed for the chemistry-education department to strengthen pre-teachers' 'Self-knowledge' in order to develop PPK. This study suggests operating 'a professional community' that has a periodic meeting with pre-service teachers, teachers, professors, community people, education practitioners, and researchers. In addition, it would be effective for increasing pre-teachers' PPK to reconsider depth and direction of 'Subject-matter knowledge', to give an opportunity to examine curriculum materials critically and reorganize them, to improve the course of chemistry experimental subject to the way of improving pre-teachers' leadership in chemistry inquiry experiment, and to raise the quality of educational service activities.

• Korean Journal of Social Welfare
• /
• v.54
• /
• pp.5-33
• /
• 2003

This study is about the re-validation evaluation of the family Relationship Scale (FRS), developed to measure the family relationship in the social work practice. This study aims at re-validating the FRS, developed and validated in by Yang in 2001 for more general utilization. The sample was married mates and females residing in Seoul. For Face Validity, the content analysis was performed, and the FRS was re-validated in the dimensions of Love & Caring, Acceptance, and Recognition, positive affection, empathy, and autonomy and flexibility for each area. Internal reliability was .93, and internal consistency among three dimensions was 93%. For Empirical Validity, the Construct validity, the Criterion validity, and the Discriminant validity were performed. Construct Validity was validated through factor analyses. Commonalities for the factor analysis was 54%, and the factor loading for each factor was over .45. The confirmative factor analysis also confirmed the fitness of the scale. For Predictive Validity of Criterion Validity, regression analysis showed that the family stress scores became lower as the scores of the family relationship became higher; the discriminant analysis revealed that the family stress turned low ill tile group of high scores of family relationship. The Correlation analysis for Concurrent Validity was performed and the results showed the positive and significant relationship with a couple communication level (r=54) and a parent-child communication level (r=64). Life satisfaction and mental health level also revealed significantly positive correlation to prove Convergent Validity. Physical health level revealed a weak relationship with family relationship providing the evidence of Discriminant Validity. Discriminance was also proved by the analysis of variance with demographics. Thus, Cross Validation was confirmed the validation of the FRS through the various analyses with the married population. This study result improved the validity generalization of the Scale and verify the generalized usage of this sociometric scale in the field of social work practice.

• Journal of Korean Academy of Nursing Administration
• /
• v.1 no.1
• /
• pp.132-146
• /
• 1995

Even though Korean medical law stipulates that number of patients attended by a nurse is 2.5 for hospitalization and 30 for ambulatory care, the number of patients cared by a nurse per day is much greater than the standard prescribed by the medical law. Current productivity of nurses is not desirable unless the quality of care is considered. And nursing manpower staffing based on neither current nurses' productivity nor standard of medical law cannot respond properly to dynamic situation of the medical services. Under this background, the necessity of more efficient management of nursing manpower occupying 1/3 of total hospital workers has been recognized by many nursing administrators. Many nursing researchers have studied to foretell the nursing manpower objectively on the basis of measured nursing workload according to patient classification as well. Most of These researches, however, have been conducted in the tertiary hospitals, so it is imperative to conduct other researches to predict necessary nursing manpower in the secondary and the primary hospitals. The study was performed to measure nursing workload and predict pertinent nursing manpower to a secondary hospital with 400beds. Nursing workload was surveyed using measuring tool for direct and indirect care hours in a surgical unit and a medical unit. Survey was conducted from Sep.10 to Sep.16 and from Oct.5 to Oct.11, 1994 respectively by two skilled nurses, Subjects were patients, patients' family members and nursing personnels. Results are follows : 1. Patient classification distributed as 22% of class I (mildly ill patient), 57% of class II (moderately ill patient), and 21% of class III (acutely ill patient) in the medical nursing unit, while 23% of class I, 29% of class II, 12% of class III, and 36% of classIV (critically ill patient) in the surgical nursing unit. There was no difference of inpatient number between weekday and weekend. Bed circulation rate was 89% in both units and average patients number per day was 37.4 (total 42beds) in the medical nursing unit, 32.9 (total 37beds) in the medical nursing unit. 2. Direct care hours per day measured as 2.8hrs for class I, 3.3hrs for class II, and 3.5hrs for class III in the medical nursing unit, while 3.1hrs for class I, 3hrs for class II, 2.7hrs for class III, and 2.2hrs for classIV in the surgical nursing unit. Meanwhile, hours for nursing assistant activities per patient by patients' family members were 11mins and 200mins respectively. Direct care hour rate by shift was day 36%, evening 25%, and night 39% in the medical nursing unit, while 40%, 29%, and and 31% respectively in the surgical nursing unit. 3. Measurement and observation activity held 44.2% of direct care activities of nurses and medication 36.7%, communication 11.7%, exercise 1.8%, treatment 1.3%, hygiene 1.3%, elimination and irrigation 1.1%, suction 1%, nutrition 0.5%, thermotherapy 0.3%, oxygen therapy 0.1% in order. 4. Indirect care hours per day were 294.2mins in the medical nursing unit, and 273.9mins in the surgical nursing unit. By shift, evening was the highest in both units. Indirect care hours for each patient were 44.5mins in the medical nursing unit and 46mins in the surgical nursing unit. 5. checking activities including doctor's order, medication, and delivering patients to the next shift occupied 39.7% of indirect care activities, and preparation 26%, recording 23.8%, communication and conference 6.7%, managing equipments 2.1%, messenger activity 1.7% in order. 6. On the ground of these results, nursing manpower needed in a secondary hospital was estimated ; 27 nursing personnels for the medical nursing unit of 37beds, and 20 nursing personnels for the surgical nursing unit of 33beds.

• Korean Chemical Engineering Research
• /
• v.60 no.2
• /
• pp.249-254
• /
• 2022

With the rapid advance of the semiconductor and Information and communication technologies, remote environment monitoring technology, which can detect and analyze surrounding environmental conditions with various types of sensors and wireless communication technologies, is also drawing attention. However, since the conventional remote environmental monitoring systems require external power supplies, it causes time and space limitations on comfortable usage. In this study, we proposed the concept of the self-powered remote environmental monitoring system by supplying the power with the levitation-electromagnetic generator (L-EMG), which is rationally designed to effectively harvest biomechanical energy in consideration of the mechanical characteristics of biomechanical energy. In this regard, the proposed L-EMG is designed to effectively respond to the external vibration with the movable center magnet considering the mechanical characteristics of the biomechanical energy, such as relatively low-frequency and high amplitude of vibration. Hence the L-EMG based on the fragile force equilibrium can generate high-quality electrical energy to supply power. Additionally, the environmental detective sensor and wireless transmission module are composed of the micro control unit (MCU) to minimize the required power for electronic device operation by applying the sleep mode, resulting in the extension of operation time. Finally, in order to maximize user convenience, a mobile phone application was built to enable easy monitoring of the surrounding environment. Thus, the proposed concept not only verifies the possibility of establishing the self-powered remote environmental monitoring system using biomechanical energy but further suggests a design guideline.

• Journal of Digital Convergence
• /
• v.20 no.4
• /
• pp.147-157
• /
• 2022

This study tried to propose a smart farm technology strategy suitable for the domestic situation, focusing on the differentiation suitable for the domestic situation of ICT technology. In the case of advanced countries in the overseas agricultural industry, it was confirmed that they focused on the development of a specific stage that reflected the geographical characteristics of each country, the characteristics of the agricultural industry, and the characteristics of the people's demand. Confirmed that no enemy development is being performed. Therefore, in response to problems such as a rapid decrease in the domestic rural population, aging population, loss of agricultural price competitiveness, increase in fallow land, and decrease in use rate of arable land, this study aims to develop smart farm ICT technology in the future to create quality agricultural products and have price competitiveness. It was suggested that the smart farm should be promoted by paying attention to the excellent performance, ease of use due to the aging of the labor force, and economic feasibility suitable for a small business scale. First, in terms of economic feasibility, the ICT technology is configured by selecting only the functions necessary for the small farm household (primary) business environment, and the smooth communication system with these is applied to the ICT technology to gradually update the functions required by the actual farmhouse. suggested that it may contribute to the reduction. Second, in terms of performance, it is suggested that the operation accuracy can be increased if attention is paid to improving the communication function of ICT, such as adjusting the difficulty of big data suitable for the aging population in Korea, using a language suitable for them, and setting an algorithm that reflects their prediction tendencies. Third, the level of ease of use. Smart farms based on ICT technology for the development of the Industry6.0 (1.0(Agriculture, Forestry) + 2.0(Agricultural and Water & Water Processing) + 3.0 (Service, Rural Experience, SCM)) perform operations according to specific commands, finally suggested that ease of use can be promoted by presetting and standardizing devices based on big data configuration customized for each regional environment.

• Journal of the Korean Society of Radiology
• /
• v.16 no.1
• /
• pp.35-43
• /
• 2022

In this study, a survey was conducted and analyzed to find out the satisfaction of online classes among students enrolled in the radiology department of a university located in Busan city. As a result, in terms of satisfaction with online classes, male scores were higher, but there was no statistically significant difference. In the interdisciplinary system, the satisfaction score of the students enrolled in Bachelor's degree was high, and there was a statistically significant difference except for the satisfaction of learning participation (p<0.001, p<0.05). For class satisfaction by grade level, Senior had higher scores, and there were statistically significant differences except for learning participation satisfaction (p<0.001, p<0.01, p<0.05). In the satisfaction survey according to the number of lectures, the scores of the students who took 4-7 lectures were found to be high except for the satisfaction of learning participation, and there was a statistically significant difference (p<0.01, p<0.05). In the method of communication with the instructor, students who used e-mail showed high scores, and there was a statistically significant difference in lecture satisfaction (p<0.05). In the correlation analysis between sub-variables for online classes, statistically significant correlations were established in all areas. Most of the students preferred class methods such as recorded classes and classes using external content such as YouTube, and when asked about the merits of online classes, many students answered that the advantages of online classes were repetitive classes and no restrictions on time and place. When asked about the shortcomings of online classes, many students answered that it was a lack of concentration and lack of communication with the instructor. This study was conducted to provide basic data to improve the satisfaction of online classes that will increase in the future. Therefore, based on the results of this study, it is expected that more quality online classes will be produced so that students' satisfaction with online classes can be improved.

• (The) Research of the performance art and culture
• /
• no.22
• /
• pp.253-285
• /
• 2011

The number of "Performing Arts Festivals" is growing increasingly in South Korea. This trend is mainly held in large cities which are difficult to communicate closely among residents. South Korea, while the pace of city life and speed of development are very fast, increasing number of "Performing Arts Festivals" with communal characteristics is in the natural process of festival evolution in large cities. In the evolution of the contemporary festival, it is natural to see some increase of modern festival after the development of traditional and folk festivals. It is important that the "Performing Arts Festivals" express the two elements, artistic character and festivity, not only in distinctively but also in harmony. The "Performing Arts Festivals" should consider the process of the organization, human resources, networking systems of the human communication process, resource use, etc. For the success of the festival, we must obtain the complementary effects between two attributes:festival characteristics and artistic senses. Therefore, we chose the 'Festival d'Avignon' as the reference of the total representation of artistic characteristics and festivity. From the case of the Festival d'Avignon, we get the implications of the development of performing arts festival in South Korea. To explain the festival value and artistic significance of the Festival d'Avignon, we explained the spontaneity and openness to public participation, the relationship between spectators and works, the representation of memory and communicative image, etc. To explain the artistic attributes of the 'Festival d'Avignon', we explained the mission to reconcile the artistic and the popular, to promote the artistic know-how, understanding how to communicate with the public, to consider more artistic quality than commercial benefits. Essentially, this study shows the meaning and the vision to forecast the future as well as the recent proliferation in various fields of Performing Arts Festivals. This study may help to improve analytical precision of Performing Arts Festivals.

• Journal of radiological science and technology
• /
• v.31 no.2
• /
• pp.109-114
• /
• 2008

There is a standard shoulder oblique method (Grashey method) available to view the shoulder joint. This method projects AP view of the shoulder joint so that the Humerus head's subuxation or joint degeneration can be easily visualized. However, in this view, the patients, with supine or sitting or erect position, have to keep their body obliquely. Whereas, the patients who are not well or operated, usually feel very uncomfortable to keep their body in this position and hence, we need other persons' help and much efforts will be needed to get the good quality shoulder joint view. Therefore, we thought of examining a method which shows the joint well by angling the tube to Medio-Lateral direction and without keeping the patients' one side upward in supine position. For this study, total 15 subjects with no history of neurological or psychiatric illness, were recruited for examinations. They consisted of 9 males and 6 females. Statistic group analysis was performed with ANOVA test. Scores of the evaluation of the experts were $1.10{\pm}0.54$ at $25^{\circ}$, $2.50{\pm}0.50$ at 30^{\circ}$, $2.85{\pm}0.36$ at $35^{\circ}$ and $2.33{\pm}0.47$ at $40^{\circ}$, respectively, and they were significant(p<0.05, Table 1). Joint space of the Humerus head and Scapula were well distinguished at $35^{\circ}$, $30^{\circ}$ and $40^{\circ}$ with the almost same score. However, the degree of distortion at $40^{\circ}$ was more severe than that at $30^{\circ}$. Ultimately, $30-35^{\circ}$ views were shown to yield good quality shoulder oblique images. In conclusion, this method may be very useful for the patients who are uncomfortable and for the emergency patients. In order to get similar or comparable view, the same X-tube angle is recommended to be used before and after the operation. Therefore, we hope that this new angled method seems to be efficient.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.143-148
• /
• 2001

PbWO$_4$ can be densified at 85$0^{\circ}C$ and it shows fairy good microwave dielectric properties; dielectric constant($\varepsilon$$_{r}$) of 21.5, quality factor(Q $\times$f$_{0}$) of 37,224 GHz, and temperature coefficient of resonant frequency($\tau$/suf f/) of -31ppm/$^{\circ}C$. Due to its low sintering temperature, PbWO$_4$ can be used as a multilayered chip component at microwave frequency with high electrical performance by using high conductive electrode metals such as Ag and Cu. However, in order to use this material for microwave communication devices, the $\tau$$_{f}$ of PbWO$_4$ must be stabilized to near zero with high Q$\times$f$_{0}$. In present study, PbWO$_4$ was modified by adding TiO$_2$, B$_2$O$_3$, and CuO in order to improve the microwave dielectric properties without increasing the sintering temperature. The addition of TiO$_2$ increased the $\tau$$_{f}$ and $\varepsilon$$_{r}$, due to its high rr(200ppm/$^{\circ}C$) and $\varepsilon$$_{r}$(100). However, the addition of TiO$_2$ reduced the Q$\times$f$_{0}$ value. When the mot ratio of PbWO$_4$ and TiO$_2$ was 0.913:7.087, near zero $\tau$$_{f}$(0.2ppm/$^{\circ}C$) was obtaibed with $\varepsilon$$_{r}$=22.3, and Q$\times$f/$_{0}$=21,443GHz. With this composition, various amount of B$_2$O$_3$ and CuO were added in order to improve the quality factor. The addition, of B$_2$O$_3$ decreased the $\varepsilon$$_{r}$. However, increased Q$\times$f$_{0}$ and $\tau$$_{f}$. When 2.5 wt% of B$_2$O$_3$ was added to the 0.913PbWO$_4$-0.087TiO$_2$ ceramic, $\tau$$_{f}$ =8.2, $\varepsilon$$_{r}$=20.3, Q$\times$f$_{0}$=54784 GHz. When CuO added to the 0.913PbWO$_4$-0.087TiO$_2$ ceramic, $\tau$$_{f}$ was continuously decreased. And $\varepsilon$$_{r}$ . and Q$\times$f$_{0}$ were increased up to 1.0 wt% then decreased. At 0.1 wt% of CuO addition, the 0.913PbWO$_4$-7.087Ti0$_2$ Ceramic Showed $\varepsilon$$_{r}$=23.5, $\tau$$_{f}$=4.4ppm/$^{\circ}C$, and Q$\times$f$_{0}$=32,932 GHz.> 0/=32,932 GHz.X>=32,932 GHz.> 0/=32,932 GHz.