• 한국분무공학회지
• /
• 제9권1호
• /
• pp.8-14
• /
• 2004

future exhaust emission limits for diesel-driven passenger cars will force the automotive company to significantly develop of the new technologies of diesel engine respectively of the drive assemblies. As we know, the contributions of soot and nitrogen oxide is the main problems in diesel engine. Recently, as a result, the pilot injection of common-rail fuel injection system recognizes an alternative function to solve an environmental problem. This study describes the effect of the nozzle structure and driven characteristic of injector on pilot injection fur a passenger car common-rail system. The pilot spray structure such as spray tip penetration, spray speed and spray angle were obtained by high speed images, which is measured by the Mie scattering method with optical system fur high-speed temporal photography. Also the CFD analysis was carried out for fuel behavior under high pressure in between needle and nozzle of injector for common-rail system to know the condition of initial injection at experiment test. It was found that solenoid-driven injector with 5-hole was faster than 6-hole injector in spray speed at same conditions and piezo-driven injector showed faster response than solenoid injector.

• 대한기계학회논문집B
• /
• 제38권2호
• /
• pp.107-114
• /
• 2014

이 연구에서는 Quantitative Feedback Theory(QFT) 기법을 이용한 승용디젤엔진의 커먼레일 압력제어 알고리즘을 제안하였다. 커먼레일 압력모델의 입력과 출력은 각각 Pressure Control Valve(PCV) 구동전류와 커먼레일 압력으로 정의하였고, Metering Unit(MeUn)이 커먼레일 압력에 미치는 영향은 모델 파라미터 불확실성으로 정의하였다. QFT 기법은 이러한 모델의 불확실성에 대하여 강건하면서도 정량적 요구사항을 만족할 수 있는 제어알고리즘 설계방법을 제시한다. 제안된 커먼레일 압력제어기는 목표 레일압력 추종성능과 안정성능이 확보되었으며, 인젝터에 의한 연료분사가 커먼레일 압력에 미치는 영향을 줄이기 위하여 외란제거성능(Disturbance Rejection)이 고려되었다. 설계된 제어 알고리즘은 엔진 동력계 실험을 통하여 검증하였으며, MeUn 구동전류와 연료분사량의 급격한 변화에 따른 제어알고리즘의 강건성과 외란제거성능을 검증하였다.

• 한국연소학회:학술대회논문집
• /
• 대한연소학회 2003년도 제27회 KOSCO SYMPOSIUM 논문집
• /
• pp.251-256
• /
• 2003

The capability of pilot injection with small fuel quantity at all engine operating conditions is one of the main feature of the common rail system. The purpose of the pilot injection is to lower the engine noise and to reduce the NOx emissions. This study describes the pilot spray structure characteristics of the common-rail diesel injectors, solenoid-driven and piezo-driven type, with different electric driving characteristics So, three common-rail injectors with different electric current wave were used in this study. The pilot spray characteristics such as spray speed, spray tip penetration, and spray angle were obtained by spray images, which is measured by the back diffusion light illumination method with optical system for high-speed temporal photography. Also the CFD analysis was carried out for fuel behavior under high pressure in between needle and nozzle of solenoid-driven injector to know the condition of initial injection at experiment test. It was found that pilot injection of common-rail system was effected by rate of injection and temperature of injected fuel and electrical characteristic of the driven injector.

• 한국가스학회지
• /
• 제20권4호
• /
• pp.44-49
• /
• 2016

본 연구는 연소실 형상 변화에 따른 디젤연소와 배출가스의 특성에 대해 살펴보았다. 발전용 커먼레일 디젤엔진의 최적화 설계를 위한 연소실형상을 제시하기 위해 5가지 타입형상을 연비 측면에서 계산하였다. 연소실 형상은 연소 시 분무면적을 변화시킴으로서 연소특성에 영향을 주었으며 이러한 주요요소는 연소실 형상 비였다. 이러한 수치해석의 결과는 연소실 형상의 변화는 발전기의 연비 개선을 가능하도록 한다고 판단되었다.

• 한국자동차공학회논문집
• /
• 제11권5호
• /
• pp.43-49
• /
• 2003

The common-rail fuel injection system is becoming a common technology for High Speed Direct Injection(HSDI) diesel engines. The injection timing and rate are important factors for combustion control and pollutants formation mechanisms during engine operation. This paper introduces an estimation methodology of the injection timing and rate of a common-rail injector for HSDI diesel engines. A sliding mode observer that is based on the nonlinear mathematical model of the common-rail injector is designed to overcome the model uncertainties. The injector model and the estimator we verified by relevant injection experiments in an injector test bench. The simulation and the experimental results show that the proposed sliding mode observer can effectively estimate the injection rate of the common-rail injector.

• 한국자동차공학회논문집
• /
• 제11권2호
• /
• pp.69-74
• /
• 2003

An experimental feasibility study of the E3.9 engine with CP3.3 and EDC7C was conducted to understand the initial performance and the possibility for EURO-III regulation. ID cycle simulation for concept study was conducted using the BOOST. Also, some basic investigations through such various parameters as injection timing and rail pressure have been carried out to find the feasibility on EURO-III ESC mode. Based on the results, the feasibility of the E3.9 engine for EURO-III characteristics such as performance, emissions, and fuel economy was demonstrated.

• 한국분무공학회지
• /
• 제17권1호
• /
• pp.1-8
• /
• 2012

This study described the effect of the multiple injections and diesel-ethanol on the NVH, combustion and emission characteristics of 4 cylinder common rail diesel engine. In order to investigate the influence of diesel-ethanol blended fuel in a light-duty common rail diesel engine, the injection strategy was varied with pilot injection, double pilot injections, and one main injection at various operating conditions. The results showed that diesel-ethanol blended fuel had longer ignition delay than that of the ultra low diesel fuel(ULSD). Also, in the case of multiple injections, the combustion pressure is increased smoothly near the TDC and the NVH are decreased. In the emission characteristics, diesel-ethanol blended fuel produced lower indicated specific nitrogen oxides(IS-NOX) and indicated specific Soot(IS-soot) emissions, however, indicated specific unburned hydrocarbon(IS-HC) and indicated specific carbon monoxide(IS-CO) emissions are slightly increased.

• 한국자동차공학회논문집
• /
• 제15권6호
• /
• pp.137-143
• /
• 2007

An object of this study is to understand the application characteristics in accordance with changes of EGR rate, applying BD20 reformed by ultrasonic energy irradiation to common-rail diesel engine. BD containing about 10% oxygen has attracted attention due to soaring crude oil prices and environmental pollution. This oxygen decreases soot by promoting combustion, but it also increases NOx. To make up for this problem, an EGR system is applied so that NOx might be decreased. In that case, engine power is lowered and exhaust gas is raised. However, the reformed fuel by ultrasonic energy irradiation is changed physically and chemically, promotes combustion, and thus solves such a problem. As the results of the experimemt, we could identify the optimum EGR rate by investigating the engine performance and the characteristics of exhaust materials in accordance with the EGR rate after ultrasonic energy irradiation to BD20 and applying it to common-rail diesel engine. The optimum EGR rate that can satisfy both engine performance and characteristics of exhaust materials was in the range of 15%.

• 한국산업융합학회 논문집
• /
• 제19권1호
• /
• pp.31-38
• /
• 2016

Since the oil shock of 1970's there was a strong upward tendency for the use of the high viscosity and poorer quality fuels. Therefore the misfiring engine occurs due to the decrease of quantity injected for lean burn and emission control in Compression Ignition Common Rail Direct Injection diesel engine. In this study, it is designed and used the test bed which is installed with fuel injector controller. In addition to equipped engine using CRDI by controlling the injection timing with mapping modulator, it has tested and analyzed the engine performance and combustion characteristics, as it is varied that they are the operating parameters: fuel injected quantity, engine speed and injection timing.

• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.26-31
• /
• 2006

An experimental investigation of an early injection strategy was conducted on a small single cylinder common-rail DI diesel engine to reduce the oxides of nitrogen($NO_x$) emission. The main objectives of this study were to investigate the emissions, performance and combustion characteristics in a diesel engine with early and two-stage injections. The two- stage injection was conducted to reduce the wall-wetting of early injected fuels on the cylinder wall or to promote the ignition of premixed charge. The engine test was performed at conditions of 1500rpm, injection timing ranging from TDC to BTDC $80^{\circ}$. The experimental results show that $NO_x$ emissions were decreased in both cases of early injection and two stage injection compared to the conventional diesel combustion by the near TDC injection. However, soot and products of incomplete products (i.e. HC and CO) are slightly increased. Also, the second injection near TDC promoted the ignition of premixed fuel, therefore, IMEP was increased.