• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.2573-2578
• /
• 2014

An experimental study was performed to investigate the characteristics of combustion pressure and exhaust emissions when the pilot injection timing and EGR rate were changed in a CRDI 4-cylinder diesel engine using bio-diesel blended fuel. The pilot injection timing and EGR rate have a significant impact on the combustion and emission characteristics of diesel engine. In this study, the pilot injection timing and EGR rate variation were conducted to 2000rpm of engine speed with fuel of bio-diesel blended rate 20%. In these experimental results, IMEP was shown maximum pressure at pilot injection timing BTDC$10^{\circ}$ combustion pressure and heat release rate were decreased in proportion to increase of EGR rate under the same pilot injection timing conditions. The NOx emission was decreased with increasing the EGR rate without influence on pilot injection timing. However, soot emission was reduced to a minimum at pilot injection timing BTDC$20^{\circ}$.

• Journal of Hydrogen and New Energy
• /
• v.34 no.1
• /
• pp.59-68
• /
• 2023

In this study, the performance of high-pressure fuel pumps was compared to find a high-pressure pump suitable for dimethyl ether (DME) fuel, and to establish a database of basic data on flow rates. The use of DME in compression ignition engines can reduce pollutant emissions. The cetane value of DME is higher than that of diesel fuel. The physical properties of DME are similar to liquefied gasoline gas (LPG), and when pressurized at a pressure of 6 bar or more, it changes from gas to liquid. Two types of high pressure pumps used in this study were independent injection type pump and a wobble plate type pump. Two high-pressure pumps with different injection types were compared. By measuring and comparing the performance changes of the two high-pressure pumps, a pump suitable for DME was selected and performance improvement measures were proposed. The changed experimental conditions to measure the performance change of the high pressure pump were increased in the units of 100 to 1,000 rpm and 100 rpm, and the experiment was performed at common rail pressures 300 and 400 bar. it was confirmed that the DME inside the fuel supply system remained in a liquid state through temperature sensors, pressure sensors, and pressure gauges. As a result of the experiment, it was confirmed that the flow rate discharged from the high-pressure fuel pump increased as the motor rotational speed increased, and the flow rate of the high-pressure fuel pump

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.2_2
• /
• pp.341-347
• /
• 2023

The subway is one of the most common and important means of transportation in modern society. In order to use the subway safely, tracks are necessary, but trains are prone to derailment and collisions. In order for the train to run safely on the track, the fishplate that connects the line connection is used. The damaged railway was a fishplate for connecting subway lines used for 11 years, and damage analysis and countermeasures were presented. Beach marks were observed on both fracture surfaces, and striations appeared at the range of crack propagation. The damaged part is Cr carbide, which has a higher hardness than the base metal, and is judged to be embrittled and destroyed by fatigue. The SM50C fishplate was subjected to a cyclic stress of about 59% of the upper limit of tensile-compression fatigue limit, but inclusions were the cause of failure. In order to prevent fatigue failure of the SM50C steel fishplate, the occurrence of inclusions should be minimized and processed to have a homogeneous structure when manufacturing the fishplate. In addition, compressive residual stress is given through surface modification such as peening to control crack generation. It is necessary to minimize the change in shape that can become a stress concentration part along with accurate fastening of the bolt, and to design the stress distribution to be as uniform as possible.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.2
• /
• pp.129-137
• /
• 2014

In this study, the characteristics of exhaust gas as a function of the biodiesel mixing ratio were investigated. Diesel and waste oil were used for preparing mixed fuel, and the ratios of the mixed fuel were varied in the BD3~BD100 range. The injection pressures(${\Delta}p_{inj}$) was considered as an experimental variable and was set to 400 bar, 600 bar, 800 bar, 1000 bar, and 1200 bar. Furthermore, for quantitatively analyzing the characteristics of exhaust gas(NOx and Soot), the concepts of Pearson correlation coefficient and Spearman rank-order correlation coefficient based on statistics were introduced. Consequently, it was found that the correlation of the emission of NOx and Soot is linear, and the Pearson and Spearman coefficients are -0.732 and -0.724, respectively, under all analysis conditions. Especially, for the injection pressure of 800 bar, a simultaneous reduction in NOx and Soot emission is possible by controlling the biodiesel mixing ratio. This is because the correlation coefficients of NOx and Soot emissions were nearly 0, as the Pearson correlation coefficient was -0.089.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.7
• /
• pp.224-236
• /
• 2017

This study analyzed the characteristics of traffic accidents among elderly drivers according to area type in Gyeonggido(urban areas, urban-rural complex areas, and rural areas). Traffic accidents caused by unsafe driving are common in all three types of areas. In urban areas and urban-rural complex areas, traffic accidents were more frequent due to traffic violations and intersection accidents, while rural areas were more affected by central lines. Urban areas and urban-rural complex areas require simpler signal exposures, such as a simple straight line, left turn, or straight line and left turn signal rather than complex signal operations, such as overlaps in a signal operation. Improvement of non-signal intersections and unprotected traffic signal processing is also needed. In order to prevent the intrusion of the central line in rural areas, the center line guard rail should be prevented from penetrating the center line, and the influence of the vehicle headlamp should be reduced in the opposite direction. It is necessary to improve the visibility by using fluorescent letters to enlarge the font size of traffic signs and road signs, particularly to increase visibility at night and prevent traffic accidents at sunset. Minimal, simplified should be provided rather than complex phrases and information.

• International Commerce and Information Review
• /
• v.15 no.2
• /
• pp.261-283
• /
• 2013

ISBP745 has new provisions about sea waybill, road, rail or inland waterway transport documents which ISBP681 did not have provisions about. The main revisions of ISBP745 which were not existent or different from ICC Opinion are as follows: First, where B/L is required when multimodal transport is used as a modes of transport, the revisions stipulates that it is subject to UCP600 article19. this differs from previous ICC Opinion. Second, when a credit requires a transport document to indicate the name, address and contact details of a delivery agent, for the place of final destination or port of discharge, the address need not be one that is located at the place of destination or port of discharge or within the same country as that of the place of destination or port of discharge. Third, in case there exist a number of shippers and a consignee, multiple transport documents are issued. This rule has a clear stipulation on this case. Transport industry regards the indication of "LCL/FCL" or "CFS/CY" common in this case as that requiring multiple transport documents. However, ISBP745 does not regard it the case as that requiring multiple transport documents. This may cause some confusion in examination of documents. Forth, when partial shipment is allowed, and more than one set of original transport documents are presented as part of a single presentation made under one covering schedule and incorporate different dates of shipment, the earliest of these dates is to be used of the calculation of an presentation period.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.2
• /
• pp.217-224
• /
• 2012

In general, transportation sources include both on-road vehicles and off-road equipment. Off-road vehicles have usually used diesel engines, which have the disadvantage of high NOx emission. Common rail direct injection (CRDI) and after-treatment systems have been applied to meet the exhaust gas emission regulations for diesel vehicles. In the present, agricultural machinery has satisfied the Tier 3 emission regulations by using waste gate turbocharger (WGT) and internal exhaust gas recirculation (EGR). In this paper, the combustion and emission characteristics of an EGR system applied to a 56kW off-road vehicle in non-road transient cycle (NRTC) mode have been investigated. The EGR map was made from foundation experiments determining the EGR duty for all engine operating conditions, and then this map was applied to the NRTC mode. Consequently, the NOx emission was reduced by the EGR system, and the Tier 4 interim emission regulations were satisfied by using both the EGR system and an after-treatment system.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.7
• /
• pp.745-752
• /
• 2012

Diesel engines are most suitable for biodiesel fuel because diesel fuel has a higher cetane number compared to gasoline and diesel engines have no spark ignition system; hence, engine conversion is easy and cost effective. For these reasons, in this study, the spray behavior characteristics of vegetable palm oil were analyzed by using a common-rail injection system of a commercial diesel engine, and the results were compared with those obtained for the diesel fuel. The injection pressures and blend ratios of palm oil and diesel fuel (BD3, BD5, BD20, BD30, BD50, and BD100) were the main parameters. The experiments were conducted for different injection pressures-500 bar, 1000 bar, 1500 bar, and 1600 bar-by setting the injection duration at $500{\mu}s$. We determined there is no significant difference in the macro characteristics of the spray behavior (spray penetration and spray angle) in response to any change in the blend ratio of palm oil and diesel fuel at a fixed injection pressure. In particular, all experiments showed a spray angle of approximately $15^{\circ}$.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1375-1381
• /
• 2011

Combustion processes in an optically-accessible single-cylinder heavy-duty diesel engine equipped with a highpressure common-rail injection system were investigated for JP-8 and diesel. Direct imaging and two-color thermometry were employed to verify the emission trend for both fuels. The combustion process was characterized by image analysis with focus on luminosity. The results of two-color thermometry were analyzed on the basis of the flame temperature and KL factor distribution. Analysis of the combustion process by direct imaging showed that the ignition delay was longer for JP-8 than for diesel, while the flame was extinguished rapidly. Analysis of the flame luminosity showed that the combustion intensity was higher for diesel and that the flame lasted for a longer duration in this case. Two-color thermometry results showed that the high-temperature region extended over a large area during JP-8 combustion, implying the formation of a large amount of $NO_x$. In addition, the KL factor showed low level over a large area and relatively homogeneous in the case of JP-8 combustion, which implied that less smoke was produced when using this fuel.

• Journal of Distribution Science
• /
• v.13 no.12
• /
• pp.53-63
• /
• 2015

Purpose - Recently, creating shared value (CSV) has attracted attention through plan sustainability and the growth of corporate management. Porter and Kramer (2011) defined the core concept of CSV as social value, economic profits, improvements in the economic social condition, and reinforcing competitiveness. The purpose of CSV, which is to pursue economic profits through a social solution to the problem, agrees with managing the objective of a social enterprise that prioritizes the pursuit of profits through the realization of a social purpose. Today, CSV studies focus on CSR and sustainability and reinforce competitiveness. However, few studies focused on the social economy. Precedent studies examined CSV using a company example, and few studies exist from the perspective of consumers and the point of view of a market society. Research design, data, and methodology - Therefore, this study examines CSV in comparison to a background of the social economy. This study also investigates and analyzes the concept of social value from the point of view of consumers, social problems, consumption value, corporate value, and the influence of consumers. This article develops three hypotheses. Hypothesis 1 investigates the correlation with social innovation that consumers thought as being necessary for social innovation by a company. Hypothesis 2 is used to confirm the influence of consumers in CSV. Therefore, this article investigates the influence of consumers on consumption action for companies that are indifferent to social problems. Hypothesis 3 is used to verify the correlation between the value that consumers demand through consumption and the corporate value that companies pursue other than profits. The three hypotheses were adopted and met the standard for suitability. Results - The importance of the CSV study from the consumer perspective was confirmed using the influence of consumers on CSV. Because the objective of company activities is either the consumer or the market, the influence that extends to interactions between the company and consumers to ensure the success of a business is significant. Regarding the CSV study, because it was an initial study, various approaches are subsequently developed. However, conceptual and practical case studies on CSV currently exist that may be used to verify the factors that comprise CSV. Therefore, the company example may enable verification of the factors that influence the composition of CSV through identification from the consumer perspective. In addition, studying CSV as an action result (of consumer satisfaction, of a company's profits and competitiveness, and of society's cancellation of a social problem) may enable the realization of a practice paradigm as opposed to simply thought and faith. Conclusions - First, this study confirms the social value of a business through the feasible and common pursuit of consumers by corporations. Second, customer influence accounts for an important part of CSV. Third, shared value commonly provides a necessary advantage to consumers, corporates, and society, and contributes to the economy and healthy social development. Fourth, corporates can conduct a business, generate profits, and realize value through improvements in social problems and by addressing their competitive strengths and weaknesses.