• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2005년도 제31회 KOSCO SYMPOSIUM 논문집
• /
• pp.104-109
• /
• 2005

This paper describes the effect of the split injection on combustion and emission characteristics in a common rail diesel engine at various operating conditions. The combustion pressures and exhaust emissions such as $NO_x$ and soot were measured at various split injection timings. The experimental apparatus of this study is composed of 4 cylinder engine installed with piezoelectric pressure sensor, EC dynamometer, and exhaust gas analyzer for the measurement of $NO_x$, CO, HC and soot emissions. Results show that the split injection has a great effect on reducing the rapid premixed combustion and $NO_x$ emissions.

• 한국안전학회지
• /
• 제2권1호
• /
• pp.11-16
• /
• 1987

A study was performed on combustion rates of three kinds of combustible substances under a few different combustion conditions. To measure the combustion rates by weight method, I contrived an apparatus using a sensitive load cell. The experimental results by the combustion tests of various combustible substances shows that the combustion circumstances, eg., air supply condition and the existence of flammable oil. And it is found that the time constant T in case of oil absence is smaller than that in case of oil existence, and the time constant T in case of enforced air-entrained condition is greater that in case of natural air-entrained condition.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권6호
• /
• pp.128-139
• /
• 2000

Environmental concerns and shortage of petroleum have promoted considerable interest in the use of alternate fuels in stationary diesel engine. In this study, a heavy-duty, intercooler-turbocharged 6-cylinder stationary diesel engine was converted into stationary gas engine fueled with propane or natural gas for the cogeneration plants. One of the most important factors in the combustion features of a stationary gas engine is the fuel composition and operating parameters in terms of compression ratio, spark advance, and engine loads. Experiments with different fuel gas and load conditions were carried out with combustion pressure analysis and NOx measurement. Combustion analysis based on P-$\theta$ diagrams was also investigated by means of combustion duration and cycle variation. Compression ratio is 10.0 and ignition timing is set by using the gasoline setting as a base line and advanced toward BTDC. The results show that fuel composition and spark advance have dominant effects on combustion and NOx characteristics at operating conditions.

• 오토저널
• /
• 제9권4호
• /
• pp.50-60
• /
• 1987

Combustion characteristics of opposed-jet-flames spouting out from dual prechambers of a divided combustion chamber were investigated by using high speed schilieren photography and chamber pressure measurement. Result shows that opposed-jet-flames are characterized by the parameter ( $A_{ori}$/ $V_{p}$) and there exists a certain critical value of ( $A_{ori}$/ $V_{p}$)c which distinguishes flame propagation patterns in the main chamber. Also higher chamber pressure and shorter total burning time can be derived by adopting this dual prechamber divided combustion chamber, which would lead a possibility of an appropriate combustion method of high load and low emissions.ons.ons.

• 한국연소학회지
• /
• 제11권1호
• /
• pp.27-33
• /
• 2006

Radiant burners are applicable to drying, preheating and curing in materials manufacturing processes. Radiation efficiency is one of the important performance criteria for these burners. The wide variation in reported radiation efficiencies are partly due to the differences in the measurement techniques. In the present work, water cooled radiant heat flux meter was used to measure radiant heat flux from a metal fiber mat burner. Non-contact type thermometer was also utilized to measure the surface temperature of the burner. Combustion gas was measured by gas analyzers. According to the thermal loads and stoichiometric ratios, radiant heat transfer ratio and combustion performance were discussed here in.

• 한국안전학회지
• /
• 제7권3호
• /
• pp.14-21
• /
• 1992

The smouldering combustion of cellulose insulation treated with boric acid-borax-alum as combustion retardants are examined by Candle type combustibility tester. This sequence was examined quantitatively for longitudinal cylinder bed of cellulose insulation. Two configuration are possible, downward and upward smoulder spread ; both were investigated exprimentally. The smoulder spread velocity of cellulose insulation was 2.5cm/s -5.0cm/s in smoulder region. As results of critical oxygen content measurement, the effectiveness of alum as third combustion retardant are acceptable for flaming retardant effect. The phenomena of combustion transition are governed by quantity of commbustible gas generation In heating zone of cellulose insulation. The critial oxygen content are decreased with the increase of gas flow rate.

• 한국연소학회지
• /
• 제1권2호
• /
• pp.9-20
• /
• 1996

We construct a mobile broadband coherent anti-Stokes Raman spectroscopy system to measure the temperature of combustion gases. To improve the accuracy of CARS temperatures due to Stokes lasers, a modeless dye laser is constructed. A monochromator to disperse CARS spectra is also constructed in the spectrometer for easy portability. The accuracy of CARS temperature, measured in graphite tube furnace in reference to a radiation pyrometer, is better than 2 % from 1000 K to 2400 K. The CARS temperature error due to the variation of the spectral distribution of the modeless laser is measured to be less than 1.5 % during five hours operation. As a demonstration of combustion diagnosis, we applied the spectrometer to measure the temperature distribution of the propane air premixed flame.

• 한국화재소방학회논문지
• /
• 제21권4호
• /
• pp.25-31
• /
• 2007

본 연구에서는 샌드위치 패널 심재에 대한 연소열과 일정한 외부 복사열에 의한 연소특성을 분석하였다. 일정한 외부 복사열원에 노출된 샌드위치 패널 심재의 착화시간, 임계열유속, 착화온도, 시료 표면 온도의 변화를 측정하기 위해 3가지 Type의 시료를 사용하였으며, 연소열을 측정하기 위해 Oxygen bomb calorimeter를, 연소특성을 측정하기 위해 Mass loss calorimeter를 사용하였다. 연소특성을 측정하기 위해 $100\;mm{\times}100\;mm{\times}50\;mm$ 크기의 시료를 사용하였다. 연구결과, 연소열과 착화온도에 있어서 가장 좋은 특성을 갖는 것은 Type B인 반면 임계열유속과 시료 표면온도 변화에 있어서는 Type C에서 가장 좋은 특성을 나타내었다. 모든 연구 데이터를 종합한 결과 Type C가 가장 좋은 화재안정성을 나타낸다는 것을 알 수 있었다. 향후, 샌드위치 패널 심재에 대한 열방출률 특성과 질량감소속도에 대한 실험연구가 필요할 것으로 판단된다.

• 대한기계학회논문집B
• /
• 제30권10호
• /
• pp.973-981
• /
• 2006

Recently there is an increasing interest in particulate matter emission because of new emission regulations, health awareness and environmental problems. It requires to improve particulate measurement techniques as well as to reduce soot emissions from combustion systems. As mentioned above, it is demanded that reduction techniques together with measurement techniques of exhausted particulate matters in combustion systems such as vehicles. However, measurement techniques of particulate matters should be prior to reduction techniques of that because it is able to know an increase and a decrease of exhausted particulate matters when measured particulate matters. Therefore, in this study, we report the measurement of soot primary-particle size using time-resolved laser induced incandescence (TIRE-LII) technique in laminar ethylene diffusion flame. As an optical method, laser induced incandescence is one of well known methods to get information for spatial and temporal soot volume fraction and soot primary particle size. Furthermore, TIRE-LII is able to measure soot primary particle size that is decided to solve the decay ate of signal S $(t_1)$ and S $(t_2)$ at two detection time. In laminar ethylene diffusion flame, visual flame height is 40 mm from burner tip and measurement points are height of 15, 20, 27.5, 30 mm above burner tip along radial direction. As increasing the height of the flame from burne. tip, primary particle size was increased to HAB(Height Above Burner tip)=20mm, and then decreased from HAB=27.5 mm to 30 mm. This results show the growth and oxidation processes for soot particles formed by combustion.

• 한국자동차공학회논문집
• /
• 제12권5호
• /
• pp.58-65
• /
• 2004

A cylindrical constant volume combustion chamber was used to investigate the combustion characteristics of stratified methane-air mixture under several initial charge conditions in the author's previous reports. The results showed that the improvement of thermal efficiency and reduction of heat loss was realized simultaneously by using 2-stage injection method. This paper deals with the reason why the stratified combustion has showed better combustion rate through the measurement and analysis of chemiluminescence of C $H^{*}$ and $C_{2}$$^{*}$ radicals. An optic fiber bundle is used to measure the local emission of C $H^{*}$ and $C_{2}$$^{*}$ radicals to map the relationship between the excess air ratio and local radical intensity ratio in the combustion vessel at 5 mm apart form the geometric center. The results show that there exist a relationship between the intensity ratio and the air-fuel ratio. It is revealed that the improvement of combustion rate in a lean-stratified mixture is realized through the 2-stage injection method. method.