• International Journal of Automotive Technology
• /
• v.8 no.1
• /
• pp.1-7
• /
• 2007

The effect of the di-tertiary butyl peroxide (DTBP) additive on the heat release rate and emissions of a homogeneous charge compression ignition (HCCI) engine fueled with high Research Octane Number (RON) fuels were investigated. The experiments were performed using 0%, 1%, 2%, 3%, and 4% (by volume) DTBP-RON90 blends. The RON90 Fuel was obtained by blending 90% iso-octane with 10% n-heptane. The experimental results show that the operation range was remarkably expanded to lower temperature and lower engine load with the DTBP additive in RON90 fuel. The first ignition phase of HCCI combustion was observed at 850 K and ended at 950 K while the hot ignition occurred at 1125 K for all fuels at different engine working conditions. The chemical reaction scale time decreases with the DTBP addition. As a result, the ignition timing advances, the combustion duration shortens, and heat release rates were increased at overall engine loads. Meanwhile, the unburned hydrocarbon (UHC) and CO emissions decrease sharply with the DTBP addition while the NOx emissions maintain at a lower level.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.96-104
• /
• 2000

It is well known that combustion stability under idle and part-load conditions directly affect fuel economy and exhaust emission. In practice, there have been a lot of studies so that a significant improvement in combustion stability has been achieved in this research field. However, applying published results to the development process of mass production engine, there are still many problems which are solved previously. In this study, initial flame behavior and flame propagation characteristic were investigated statistically in order to optimize combustion chamber shapes in the development stage of mass production S.I. engine. To the purpose, the authors applied the flame image capturing system to single cylinder optical engine. The captured flame images were effectively analyzed by using the image processing program which was developed by the authors and adopted new threshold algorithm instead of conventional histogram analysis. In addition, the cylinder pressure was also measured simultaneously to compare evaluated flame results with cylinder pressure data in terms of the combustion characteristics, combustion stability, and cycle-to-cycle combustion variability.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.25 no.2
• /
• pp.82-86
• /
• 1989

This paper is concerned with the effects of temperature of diesel fuel on combustion characteristics and engine performance in a home-made precombustion diesel engine for small-sized fishing boat. The results may be summarized as follows: 1. The fuel injection timing was delayed with increase in temperature for diesel fuel, and remarkably delayed at low load. 2. The point of maximum pressure was delayed with increase in temperature for diesel fuel, the maximum pressure decreased with increase in temperature for diesel fuel but increased with increase in load. 3. The brake specific fuel comsumption (BSFC) decreased with increase in load, the optimum temperature of the heated fuel was about 15$0^{\circ}C$. 4. The smoke emissions increased with increase in load and temperature for diesel fuel.

• Journal of the Korean Society of Combustion
• /
• v.15 no.3
• /
• pp.57-66
• /
• 2010

The purpose of this paper is to investigate the effects of fuel injection strategy and engine load on the structure and emissions characteristics of a DI diesel engine with 1.6L of piston displacement. In order to analyze the particulate matter (PM) and exhaust emissions characteristics in a direct injection diesel engine, the quantity of PM and exhaust emissions (including HC, CO and $NO_X$) were investigated under various injection strategies and engine loads. Two different injection strategies (one pilot/main injection and two pilots/main injection) was investigated under the various engine loads. A thermophoretic sampling method with a scanning electron microscope (SEM) were used to obtain the PM morphology (including primary particles, the size of the agglomerates, the number of agglomerates, the fractal dimension). The quantity of soot gradually increased with increasing engine load at both injection strategies. The primary particles in the PM agglomerates indicate that the average of the primary particle and radius of gyration increased as the engine load increased.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.41-42
• /
• 2006

A study on the combustion characteristics by using Emulsion Fuel in Diesel Engine is performed experimentally. In this paper, the experiments are performed at engine speed 1800rpm, emulsion fuel ratio is 0%, 10%, 20%, and main measured items are specific fuel consumption, pressure, ratio of pressure rise, rate of heat release etc. The obtained conclusions are as follows. 1) Specific fuel consumption increase maximum 19.8% at low load, but is not effected at full load. 2) Ratio of pressure rise and rate of heat release are about the same in the case of 10% and 20% of emulsion fuel ratio. 3) Cylinder Pressure increase 11.7%, ratio of pressure rise increase 60.4% in case of emulsion fuel ratio 20% at full load. 4) Rate of heat release increase 76.9% in case of emulsion fuel ratio 20% at full load.

• Journal of Power System Engineering
• /
• v.14 no.3
• /
• pp.13-18
• /
• 2010

HCCI engines fueled DME and natural gas have been studied on single-cylinder engine due to availability of reducing on $NO_X$ and PM simultaneously without deteriorating into high thermal efficiency, and thus it is clarified that higher maximum engine load is achieved as DME equivalence is smaller. In this study, combustion tests were accomplished on multi-cylinder engine for practical use of it. When minimum DME equivalence achieved maximum engine load on single-cylinder engine was applied to 4-cylinders engine, there was in unstable running condition that engine revolution fluctuated greatly and cyclically. It is the reason what misfire occurred intermittently with one the same as minimum DME equivalence on single-cylinder due to increase in energy for ignition at No. 1 cylinder with lower cylinder liner temperature. Maximum engine load was achieved by adopting EGR, though it decreased because of knocking at smaller engine load than single-cylinder due to increase in minimum DME equivalence.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.6
• /
• pp.416-426
• /
• 2008

The boiler tube failure often experienced in the superheater of a utility boiler can seriously affect the economic and safe operation of the power plant. It has been known that this failure is mainly caused by the thermal load deviation in the superheater tube system, and deeply intensified by the non-uniform distribution of steam flow rates. The nonuniform steam flow is distinctively prominent at low power load rather than at full power load. In this paper, we analyze the steam flow distribution in the superheater tube system by using one dimensional flow network model. At 30% power load, the deviation of steam flow rate is predicted to be within 0.8% of the averaged flow rate. This deviation can be reduced to 0.1% and 0.07% by assuming two cases, that is, the removal of 13th tube at each tube rows and the installation of intermediate header, respectively. The assumed two cases would be effective for the uniform steam flow distribution across 85 superheater tube rows.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.3
• /
• pp.206-215
• /
• 2013

A linear engine has advantages in terms of volume and weight, because there are no rotating parts. Thus, it is considered that linear engines might be suitable in hybrid vehicles. However, the linear engine has challenges in terms of the engine ignition timing and efficiency, so the engine has not been commercialized yet. In this study, the dynamic and combustion characteristics of the linear engine might be specified by various loads which are changed by conductance. The engine used in this experiment consists of two combustion chambers, four compressors, two linear alternators and a mover with a piston head and magnets. The way fuel is supplied in the experiment is by propane fuel being mixed with air in the carburetor, then being delivered into combustion cylinders via compressors. In the experiment, conductance is altered from 0.04 to 0.16mho, and the ignition timing is ahead by just 5.0mm from the maximum stroke. As a result of the experiment, frequency, stroke, input calories and maximum pressure are decreased when the conductance is increased. Meanwhile, IMEP, generation efficiency and electric power are increased when the conductance is increased. Therefore, it might confirm that high conductance generates more efficient electric power, but that thermal efficiency is the highest in the state of 0.08mho.

• Journal of Energy Engineering
• /
• v.22 no.2
• /
• pp.169-174
• /
• 2013

An experimental study has been conducted for the design of the regenerative oxy-fuel combustion system with ceramic ball. Various design parameters are considered such as ball size, regenerator weight, and combustion load. Regenerative system with a pair of oxygen burners and regenerators is set up and the temperature of oxygen and exhaust gas passing through ball regenerator is measured. It is shown that the temperature distributions with time are affected by ball diameter and regenerator weight, and the significant temperature change is observed by combustion load. As the ball size decreases and the regenerator weight increases, the regenerating temperature efficiency increases. It is found that the heat recovery ratio is low despites of high regeneration temperature efficiency.

• Journal of ILASS-Korea
• /
• v.24 no.1
• /
• pp.35-42
• /
• 2019

Syngas is widely produced by incomplete combustion of coal, water vapor, and air (oxygen) in a high-temperature/high-pressure gasifier through a coal-gasification process for power generation. In this study, a simulation syngas which was mainly composed of $H_2$, CO, $CO_2$, and $N_2$ was fueled with diesel. A modified single cylinder compression ignition (CI) engine is equipped with intake port syngas supply system and mechanical diesel direct injection system for dual fuel combustion. Combustion and emission characteristics of the engine were investigated by applying various syngas composition ratios and compression ratios. Diesel fuel injection timing was optimized to increase indicated thermal efficiency (ITE) at the engine speed 1,800 rpm and part load net indicated mean effective pressure ($IMEP_{net}$) 2 to 5 bar. ITE of the engine increased with the $H_2$ concentration, compression ratio and engine load. With 45% of $H_2$ concentration, compression ratio 17.1 and $IMEP_{net}$ 5 bar, ITE of 41.5% was achieved, which is equivalent to that of only diesel fuel operation.