• The Korean Journal of Ceramics
• /
• v.6 no.2
• /
• pp.172-176
• /
• 2000

Solid solutions of Ti$_{0.5}$Zr$_{0.5}$B$_2$were successfully synthesized and densified simultaneously from elemental reactants by the use of a field-activated, pressure-assisted synthesis method. The method involves the application of an electric current and mechanical pressure across reactant compacts to achieve combustion synthesis. Dense solid solutions with relative densities of up to 99% were produced and characterized by XRD, SEM, and EPMA methods. With a maximum measured temperature of 145$0^{\circ}C$ under a load of 86 MPa for 30 min, the desired dense solid solution wad synthesized.

• Journal of the Korean Society of Combustion
• /
• v.18 no.1
• /
• pp.7-12
• /
• 2013

A quasidimensional program is developed for a four stroke cycle homogeneous GDI (Gasoline Direct Injection) engine. It includes models for spray, burning rate and chemistry to predict knock and emissions. With early injection a homogeneous GDI engine goes through spark ignited, turbulent premixed combustion as in PFI (Port Fuel Injection) engines. The cylinder charge is divided into unburned and burned zone with the latter divided into multiple zones of equal mass to resolve temperature stratification. Validation is performed against measured pressure traces, NOx and CO emissions at different load and RPM conditions. Comparison is made between an empirical knock model and predictions by the chemistry model in this work.

• Journal of the Korean Society of Combustion
• /
• v.3 no.1
• /
• pp.31-39
• /
• 1998

The local instantaneous flame temperature and soot concentration in a D. I. diesel engine were measured using a two-color method. The proposed method based on the continuous spectra! radiation from the soot particles in the flame is applicable to industrial Diesel engines without major modifications of their main characteristics because of simplicity and relative ease of application. Measurements were performed at two locations inside the combustion chamber of a D. I. diesel engine. Effects of different engine speeds and loads, fuel injection timings, combustion chamber shapes on flame temperature and KL factor, which is qualitatively proportional to soot concentrations, were examined. Flame temperature change were observed with increasing engine speed and load. The higher the flame temperature is, the lower the KL factor is.

• 한국연소학회:학술대회논문집
• /
• 2000.12a
• /
• pp.59-66
• /
• 2000

In this study, We studied flow and combustion characteristics of a Flat Flame Burner(FFB) with swirler. As swirl number increase, the streamlines is proceed close to tile and velocity is large. Blow-off limit decrease when swirl number is 1.24, but blow-off limit increase when combustion load is 6500kcal/hr. Temperature distribution is uniform in front of tile and NO formation is small at S=1.24. We expect that the radiation can be transmitted to the object and NOx will reduce because of recirculation zone

• Journal of the Korean Society of Combustion
• /
• v.16 no.3
• /
• pp.27-32
• /
• 2011

This study has numerically investigated the flame structure and emission characteristics in the metal fiber burner. The one-dimensional premixed flame approach has been adopted to simulate the combustion processes of the metal fiber burner. Numerical results indicate that the present approach is capable of predicting the essential combustion characteristics of the metal fiber burner. Based on numerical results, the detailed discussion has been made for the effects of equivalence ratio and thermal load on the precise flame structure and the pollutant emission in the metal fiber burner.

• Journal of Mechanical Science and Technology
• /
• v.14 no.4
• /
• pp.426-432
• /
• 2000

The development of a low-pollution burner is important for saving energy and preserving the environment. A low-pollution burner can be produced by lean-mixture combustion and general combustion technology. The flammable limit of premixed flame is narrower than that of diffusion flame. Producing a lean mixture of fuel results in an effective combustion condition, which in turn produces high load and low pollution. In this study, it was found that the influx of $Q_2$ had an effect on extending the lean flammable limits and flame stabilization in a doubled jet burner. And the flame, consisting of small eddies, can be stabilized by the nozzle neck phenomena.

• Journal of Mechanical Science and Technology
• /
• v.17 no.10
• /
• pp.1563-1571
• /
• 2003

A fast response NO analyzer was applied to investigate the relation between cycle-by-cycle NO emissions and combustion chamber pressure. NO emissions were sampled at an isolated exhaust manifold of 4-stroke spark ignition engine to avoid the interference of exhaust gas from other cylinders. The linear correlation analysis was performed with collected data of NO emissions and combustion chamber pressure with respect to the various air-fuel mixture ratios and engine loads. The sampled data sets were obtained during 200 cycles at each operating condition. The results showed that there was a typical pattern in NO emissions from an exhaust port through a cycle. It was possible to set a block of crank angle in which the linear correlation coefficient between NO emissions and combustion chamber pressure was high. As the engine load increased, NO emissions were more dependent on combustion chamber pressure after TDC. It was also analyzed that the correlation between two parameters with respect to air-fuel mixture ratio tended to increase as mixture went leaner. Furthermore, this correlation coefficient for the mixture near the lean limit seemed to be kept high even though combustion was unstable.

• Journal of Power System Engineering
• /
• v.20 no.2
• /
• pp.32-42
• /
• 2016

Under part load condition of spark-ignition engine, pumping loss had great effect on engine efficiency. To reduce pumping loss, the study designed spark-ignited engines to make direct spray of gasoline to combustion chamber. In spark-ignited direct-injection engines, ignition probability is important for successful combustion and flame propagation characteristics are also different from pre-mixed combustion. This study designed a visualization testing device to study ignition probability of spark-ignited direct-injection LPG fuel and combustion flame characteristics. This visualization device consists of combustion chamber, fuel supply system, air supply system, electronic control system and data acquisition system. Ambient pressure, ambient temperature and ambient air flow velocity are important parameters on ignition probability of LPG-air mixture and flame propagation characteristics, and the study also found that sprayed LPG fuel can be directly ignited by spark-plug under proper ambient conditions. To all successful cases of ignition, the study recorded flame propagation image in digital method through ICCD camera and its flame propagation characteristics were analyzed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.54-66
• /
• 2000

A gasoline direct injection single cylinder engine has been developed to study operational characteristics for highly stratified conditions. Parameters related to design and experiment were also studied to understand the characteristics of combustion and emissions at some part load conditions. It was found that optimal timings between the end of fuel injection and spark ignition were existed for stable combustion under the stratified modes, In a low engine speed, fuel spray behavior around piston bowl was important for stable combustion. The in-cylinder air motion affecting fuel spray behavior was found to be a dominant factor at higher engine speed as fuel injection timing had to be advanced to secure enough time for fuel evaporation and mixing with surrounding air. As swirl ratio increased, spark timing could be advanced for stable combustion and a higher compression ratio could be used for improved fuel consumption and stable combustion at the stratified mode. It was also observed that electrode geometry and piston bowl shape played an important role for combustion and emission characteristics and some results were shown for comparison.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.48-55
• /
• 2003

The effects of pressure charge on combustion stability and emissions have been analyzed using a GDI single cylinder engine. A late injection mode of stratified condition at the air-fuel ratio of 40:1 for 1200∼2400 rpm was tested while the boosted pressure ratio was increased up to 1.5:1. In-cylinder CFD analysis was also performed for better understanding of in-cylinder flow and fuel spray behavior. With a higher boosted pressure ratio the IMEP was increased greatly due to the increased engine load, and the ISFC was improved by more than 10% at all engine speeds. The regime of stable stratified combustion was extended to a higher engine speed, but the spark ignition angle had to be more advanced for stable combustion. The emissions of ISHC and ISNOx did not show a particular trend for the increased engine speed but a general trend of lower ISHC and higher ISNOx for a gasoline engine.