• Journal of Environmental Science International
• /
• v.14 no.12
• /
• pp.1185-1194
• /
• 2005

The runoff characteristics of non-point source pollutions in the municipal area of Jeonju were investigated and analyzed by using the SWMM (Storm Water Management Model). The flow rates and water qualities of runoff from two types of drainage conduits were measured respectively. One was a conventional combined sewer system and the other was a separated sewer system constructed recently From August to November in 2004, investigations on two rainfall events were performed and flow rate, pH, BOD, COD, SS, T-N and T-P were measured. These data were also used for model calibration. On the basis of the measured data and the simulation results by SWMM, it is reported that $80-90\%$ of pollution load is discharged in the early-stage storm runoff. Therefore, initial 10-30 mm of rainfall should be controlled effectively for the optimal treatment of non-point source pollution in urban area. Also, it was shown that the SWMM model was suitable for the management of non-point source pollution in the urban area and for the analysis of runoff characteristics of pollutant loads.

• Journal of Korean Society of Transportation
• /
• v.22 no.2 s.73
• /
• pp.109-119
• /
• 2004

In COSMOS, an area for signal coordination is divided into subareas composed of several signalized intersections that share a common cycle time. Each subarea contains only one critical intersection having heavy traffic load. Subarea is a basic unit of control. The performance of COSMOS is highly dependent on the linkage rule between adjacent subareas. The purpose of this study is to provide an appropriate subarea linkage rule in COSMOS. This study developed a control strategy for Critical Intersection and Sub Area linkage. Critical Intersections calculate the Offset Pattern both East-West Axis and North-South Axis, and the coordination direction either East-West Axis or North-South Axis. Subarea can be combined with other one in all directions. The performance of the suggested linkage rule was evaluated on the real network in Gangnam-Gu. The result was that travel time was reduced by the suggested linkage rule.

• Tribology and Lubricants
• /
• v.32 no.1
• /
• pp.1-8
• /
• 2016

This paper focuses on the thermal deformation induced preload change in the tilting pad journal bearing, using a three-dimensional (3D) thermo-hydro-dynamic (THD) approach. Preload is considered as a critical factor in designing the tilting pad journal bearing. The initial preload measured under nil external load and nil thermal gradient is influenced by two factors, namely, the thermal deformation and elastic deformation. Thermal deformation is due to a temperature distribution in the bearing pads, whereas the elastic deformation is due to fluid forces acting on the pads. This study focuses on the changes induced in preload and film clearance due to thermal deformation. The generalized Reynolds equation is used to evaluate the force of the fluid and the 3D energy equation is used to calculate the temperature of the lubricant. The abovementioned equations are combined by establishing a relationship between viscosity and temperature. The heat transfer within the bearing pads, the lubricant, and the spinning journal is calculated using the heat flux boundary condition. The 3D Finite Element Method (FEM) is used in modeling the (1) heat conduction in the spinning journal and bearing pads, (2) thermal gradient induced thermal distortion of the spinning journal and pads, and (3) viscous shearing, and heat conduction and convection in a thin film. This evaluation method has an increased fidelity, and it can prove to be a cost-effective tool that can be used by designers to predict the dynamic behavior of a bearing.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.117-125
• /
• 2014

The temperature distribution of steady state rolling tires with detailed tread blocks is numerically predicted using the three dimensional full patterned tire model. A three dimensional periodic patterned tire model is constructed by copying 1-sector mesh in the circumferential direction. Using the static tire contact analysis, the strain cycles during one revolution are approximated with the strains at Guassian points of the elements which are sector-wise repeated within the same circular ring of elements, by neglecting the tire rolling effect. Based upon the multi-axial fatigue theory, the maximum principal strain is used to represent the combined effect of six strain components on the hysteretic loss. In the following, the deformation due to the inflation and vertical load is calculated using ABAQUS. Then heat generation rate in each element is calculated using an in-house code. Lastly, temperature distribution is calculated using ABAQUS again. Through the numerical experiments, the validity of the proposed prediction method is examined by comparing with the experiment and the temperature distribution of a patterned tire model is compared with those of the main-grooved simple tire model.

• The Journal of the Korea Contents Association
• /
• v.11 no.12
• /
• pp.560-569
• /
• 2011

In this paper, we propose a text processing method for Hindi characters, Devanagari scripts, in the Android. The key points of the text processing are to device automata, which define the combining rules of alphabets into a set of syllables, and to implement a font rendering engine, which retrieves and displays the glyph images corresponding to specific characters. In general, an automaton depends on the type and the number of characters. For the soft-keyboard, we designed the automata with 14 consonants and 34 vowels based on Unicode. Finally, a combined syllable is converted into a glyph index using the mapping table, used as a handle to load its glyph image. According to the multi-lingual framework of Freetype font engine, Dvanagari scripts can be supported in the system level by appending the implementation of our method to the font engine as the Hindi module. The proposed method is verified through a simple message system.

• Journal of Biosystems Engineering
• /
• v.39 no.4
• /
• pp.274-282
• /
• 2014

Purpose: In this study, a hybrid power system was developed for agricultural machines with a 20-KW output capacity, and it was attached to a multi-purpose cultivator to improve the performance of the cultivator, which was evaluated using output tests. Methods: The hybrid system combined heterogeneous sources: an internal-combustion engine and an electric power motor. In addition, a power splitter was developed to simplify the power transmission structure. The cultivator using the hybrid system was designed to have increased fuel efficiency and output power and reduced exhaust gas emissions, while maintaining the functions of existing cultivators. Results: The fuel consumption for driving the cultivator in the hybrid engine vehicle (HEV) mode was 341 g/KWh, which was 36% less than the consumption in the engine (ENG) mode for the same load. The maximum power take off output of the hybrid power system was 12.7 KW, which was 38% more than the output of the internal-combustion engine. In the HEV mode, harmful exhaust gas emissions were reduced; i.e., CO emissions were reduced by 36~41% and NOx emissions were reduced by 27~51% compared to the corresponding emissions in the ENG mode. Conclusions: The hybrid power system improved the fuel efficiency and reduced exhaust gas emissions in agricultural machinery. Lower exhaust gas emissions of the hybrid system have considerable advantages in closed work environments such as crop production facilities; therefore, agricultural machinery with less exhaust gas emissions should be commercialized. However, the high manufacturing cost and complexity of the proposed system are challenges which need to be solved in the future.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.12
• /
• pp.92-100
• /
• 2005

An aircraft wing or fuselage panel of skin-stringer assembly can fail in a variety of instable modes under compression loads. Instability modes can be buckling of the panel, local buckling of the stringer, flexure, torsion, wrinkle and combined flexural/torsional buckling of the panel assembly. Although researches on these buckling behaviors have been carried out for a long time, there are some difficulties to apply to the practice because of complex theoretical and empirical equations. Accordingly, It is well known that leading aerospace companies are using their own in-house programs for the convenience of practical usage, but our domestic situation is that no such program has been ever developed. In this study a comprehensive program has been developed, which can identify the instability modes and the magnitude of reserve factor of the modes for the skin/stringer panel assembly under compression load. The developed program is based on the theory manual of the Airbus program APA114. For the verification, calculation of the instable reserve factors for the A320 wing panel and A380 low wing panel sections were carried out and compared with results by APA114.

• Journal of KIISE:Information Networking
• /
• v.36 no.2
• /
• pp.118-129
• /
• 2009

The ISO 18000-7 Active RFID standard, a single channel system operating in the 433Mhz, faces technical difficulties in supporting some recently introduced application demands because of its low transmission rates and radio interference between readers. We propose a new multi-channel active RFID system operating in the 2.4Ghz. The special feature of the proposed system is that a reader makes use of multiple interfaces to improve its performance like a multi-core processor. However if only a small part of interfaces are actually used, the performance improvement would not meet the expectation. To overcome this problem, a new multi-channel multi-interface active RFID protocol, which balances communication loads among all available interfaces, is necessary. 3 protocols, named as "Aggregated", "LP-Combined", "AP-Balanced", are proposed. Through simulation, we compare them for various conditions by changing number of tags, number of interfaces, tag data size. AP-Balanced shows the best performance and its performance increases almost linearly as the number of interface increases, which meets our expectation.

• Structural Engineering and Mechanics
• /
• v.67 no.6
• /
• pp.579-585
• /
• 2018

Masonry walls are of a complex (anisotropic) structure in terms of their mechanical properties. The mechanical properties of the walls are affected by the properties of the materials used in wall construction, joint thickness and the type of masonry bond. The carried-out studies, particularly in the seismic zones, have revealed that the most of the conventional masonry walls were constructed without considering any engineering approach. Along with that, large-scale damages were detected on such structural elements after major earthquake(s), and such damages were commonly occurred at the brick-joint interfaces. The aim of this study was to investigate the effect of joint thickness and also type of mortar on the mechanical behavior of the masonry walls. For this aim, the brick masonry walls were constructed through examination of both the literature and the conventional masonry walls. In the construction process, a single-type of brick was combined with two different types of mortar: cement mortar and hydraulic lime mortar. Three different joint thicknesses were used for each mortar type; thus, a total of six masonry walls were constructed in the laboratory. The mechanical properties of brick and mortars, and also of the constructed walls were determined. As a conclusion, it can be stated that the failure mechanism of the brick masonry walls differed due to the mechanical properties of the mortars. The use of bed joint thickness not less than 20 mm is recommended in construction of conventional masonry walls in order to maintain the act of brick in conjunction with mortar under load.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.8
• /
• pp.113-120
• /
• 2007

This paper presents the electric shock hazards and solutions of loss of the combined protective and neutral (PEN) conductor in TN-C-S system. In order to mitigate the touch voltage on exposed-conductive-parts in a break in the PEN conductor, the touch voltages on exposed-conductive-parts in a break in the PEN conductor were experimentally investigated as a function of the ground resistances of the source grounding electrode and customer's additional grounding electrode. As a result, the equipotential bonding is one of important requirements for installations supplied by TN-C-S system. A solution of mitigating the touch voltages on exposed-conductor-parts caused by a loss of the PEN conductor would be the installation of the additional grounding electrode at the customer's service entrance. The ground resistance of additional grounding electrode necessary to limit the touch voltage to a safety voltage of less than 50[V] depends on the load and circuit parameters. In addition, the undervoltage sensing devices oner affordable solutions to detect a loss of the PEN conductor in TN-C-S system.