• Journal of information and communication convergence engineering
• /
• v.17 no.3
• /
• pp.205-212
• /
• 2019

Motion tracking and localization devices are an important building block of motion tracking systems in a virtual reality (VR) environment. This study is about improving the accuracy of motion and location for enhancing user immersion in experience type VR environment to position tracking technique. In this study, we propose and test a design of such a device. The module data test of the attitude and heading reference system shows that the implementation with the MPU-9250 sensor is successful and adequate to be used with short operation time. We consider various sensor hardware dependencies of VR, and compare various correction methods and filtering methods to lower the motion to photon (MTP) time that user movement is fully reflected on the display using sensor devices. The Kalman filter is used to combine the accelerometer with the gyroscope in the sensing unit.

• Journal of KIISE:Computing Practices and Letters
• /
• v.16 no.12
• /
• pp.1177-1187
• /
• 2010

Flash memory becomes popular storage for small devices due to its efficiency, portability, low power consumption and large capacity. Unlike on hard disks, however, write operation on flash memory is much more expensive than read operation, so that it is critical for performance enhancement to reduce the number of executions of write operation. This paper proposes static analysis to rewrite a program to reduce the total number of write operations by merging writable data in a minimum number of pages. To achieve this, we collect information about writable areas by static analysis, and about frequently executed paths by profiling for practicality, and combine both to rewrite the application program to reallocate data. The performance enhancement gained from the proposed methods is shown using a FAST simulator.

• Journal of the Korea Society of Computer and Information
• /
• v.10 no.5 s.37
• /
• pp.87-94
• /
• 2005

This paper describes the method of detecting the region of vehicle number plate in colored car image with number plate. Vehicle number plate region generally shows formula colors in accordance with type of car. According to this, we use the method to combine a color ingredient H of HSI color model and a color ingredient Q of YIQ color model. However, the defect which a total operation time takes much exists if it uses such method. Therefore, in this paper, the concurrent accomplishes a candidate area extraction operation as draw a color H and Q ingredient among steps of extracting a region of vehicle number Plate. After the above step, as a next step in combination with color H and Q we can accomplish an region extraction fast by comparing to candidate regions extracted from each steps not to do a comparison operation to all of image pixel information. We also show implementation results Processed at each steps and compare with extraction time according to image resolutions.

• Journal of Korea Water Resources Association
• /
• v.44 no.12
• /
• pp.1001-1013
• /
• 2011

Development of an optimal water supply system considering water quantity, quality, and economical efficiency is needed to decide optimal available area by combine water supply systems in overlapped area where are more than 2 water sources. The EPAnet and the KModSim were coupled to develop optimal network model. The developed network model was calibrated by measured data from water supply system in Geoje City, Korea in 2007 which have three water sources such as Sadeong booster pumping station, Guchun dam reservoir and Yoncho dam reservoir. The optimum network model was validated by operating results of 2011 to assess the economically optimized service area and optimal pump combination under the given hydraulic operating rules developed in this study. The developed model can be applied into designing water supply systems and operating rules for the conjunctive operation since the model can give the optimal solution satisfied with water quantity, economical efficiency and quality.

• Korean Journal of Agricultural Science
• /
• v.43 no.4
• /
• pp.688-703
• /
• 2016

The 6th industrialization, which is the policy strategy to combine the 1st, 2nd, 3rd agro-food industries in order to create synergy effects, is one of the most important policy strategies for the Korean government. Local governments as well as the central government, especially the Ministry of Agriculture, Food and Rural Affairs, have introduced various specific programs for the 6th industrialization. Among them, the 6th industry antenna shops located in Cheonan and Daejeon which were introduced by the Chungcheongnam-do Provincial Government to offer a better market place for 6th industry producers. However, few studies have been conducted to evaluate the performance of 6th industry antenna shops. The purpose of this paper is to analyze consumers' satisfaction of 6th industry antenna shops through survey and econometric modeling and to present some implications of the better operation of the 6th industry antenna shops. The results of the studies in this paper present some of the following findings: first, the overall level of satisfaction towards 6th industry antenna shops is high but consumers still claim some problems. Second, products which are sold at 6th industry antenna shops have important problems, including high prices and deficient product variety. Third, if these problems were fixed, the operation of 6th industry antenna shops would be successful and contribute to the development of 6th industrialization in Korea.

• International Journal of Quality Innovation
• /
• v.9 no.3
• /
• pp.29-56
• /
• 2008

Since the execution of National Health Insurance system in Taiwan, the competition of medical industry is becoming more and more severe. The ways the hospital operate knowledge management (KM) concept, combine current human resources and professional knowledge by information techniques and upgrade the competitiveness through reinvention of organizational culture have become the important issues. This research is based on the relationship between KM and organizational operation, integrates the characteristic of medical institutions and framework of medical knowledge cycle and starts the research subject by questionnaires from three dimensions: current situation of KM construction in medical organizations, executive effect of KM activities and the challenges faced by KM; subsequently, from qualitative interview, this research attempts to understand how a medical organization executes and adjusts in the consideration of theory and reality as well as quality and costs when actually operates the organization. This research accesses to KM system application of medical institutions and the empirical executive benefits and difficulties through questionnaires. The research results are as follows: (1) having initial understanding toward current KM establishment of medical institutions; (2) confirming the most important items of KM establishment of medical organizations; (3) understanding the most difficulty which the medical organizations encounter when executing KM; (4) establishing medical knowledge cycle figure of the hospitals receiving interviews. Through case interview, this research profoundly accessed to the actual operation of KM application of medical organizations. The target hospitals intended to try many medical KM measures; however, during to complicated hospital organizations and cultural characteristics, the promotion was not successful and the results were not apparent. The most difficulty was to change the employees’ behavior. The targets believed that only the continuous promotion of KM can allow it to be an important aspect of organizational culture and the competitiveness could constant be upgraded.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.493-496
• /
• 2005

The PMU (Payload Management Unit) in MSC (Multi-Spectral Camera) is the main subsystem for the management, control and power supply of the MSC payload operation. The PMU shall handle the communication with the BUS (Spacecraft) OBC (On Board Computer) for the command, the telemetry and the communications with the various MSC units. The PMU will perform that distributes power to the various MSC units, collects the telemetry reports from MSC units, performs thermal control of the EOS (Electro-Optical Subsystem), performs the NUC (Non-Uniformity Correction) function of the raw imagery data, and rearranges the pixel data and output it to the DCSU (Data Compression and Storage Unit). The BUS provides high voltage to the MSC. The PMU is connected to primary and redundant BUS power and distributes the high unregulated primary voltages for all MSC sub-units. The PSM (Power Supply Module) is an assembly in the PMU implements the interface between several channels on the input. The bus switches are used to prevent a single point system failure. Such a failure could need the PSS (Power Supply System) requirement to combine the two PSM boards' bus outputs in a wired-OR configuration. In such a configuration if one of the boards' output gets shorted to ground then the entire bus could fail thereby causing the entire MSC to fail. To prevent such a short from pulling down the system, the switch could be opened and disconnect the short from the bus. This switch operation is controlled by the BUS.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.40 no.6
• /
• pp.132-140
• /
• 2003

In this paper, we propose a new scheme for view-dependent transmission of three-dimensional (3-D) polygonal mesh models with hierarchial partitioning. In order to make a view-dependent representation of 3-D mesh models, we combine sequential and progressive mesh transmission techniques. By setting higher priorities to visible parts than invisible parts, we can obtain good qualify of 3-D models in a limited transmission bandwidth. In this paper, we use a multi -layer representation of 3-D mesh models based on hierarchical partitioning. After representing the 3-D mesh model in a hierarchical tree, we determine resolutions of partitioned submeshes in the last level. Then, we send 3-D model data by view-dependent selection using mesh merging and mesh splitting operations. By the partitioned mesh merging operation, we can reduce the joint boundary information coded redundantly in the partitioned submeshes. We may transmit additional mesh information adaptively through the mesh spritting operation.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.539-546
• /
• 1996

The physical condition of rapeseed delivered to fat industry plants plays a significant role in the formation of the qualitative features of the raw material for oil production and, consequently , of the oil itself. Rapeseed is stored in silos , frequently for months, before it is subjected to processing. During the long storage, the conditions of the seed cover is very important, as the seed cover provides natural protection of the seed against the effect of the environment. Seeds with damaged seed cover are more easily affected by mildew, and the rate of chemical processes. Deteriorating the quality of oil contained in the cotyledons is faster in such seeds. Cracked seed covers facilitates also the growth and development of microorgaism. So as rapeseed damage occurring inthe course of harvest and the post-harvest processing have a negative effect of the quality and quantity of oil the sees contain. The study presented here was aimed at examining the typical process of purcha ing and handling of rapeseed in fat industry plants, in the aspect of the occurrence of mechanical damage to the seeds. Special attention was paid to the condition of rapeseed immediately after combine harvesting : next , the successive stages of technological handling of the seed were examined. observing the operation parameters of the particular machinery and equipment in order to identify those operations which caused deterioration in the quality of the material (sees). Seed samples were taken successively from the following the hopper, prior to cleaning , after cleaning , prior to drying , after drying, from dry rape silo. The total level of damage increased through the handling. The content of unusable contaminants had the tendency to decrease in the successive operations. though the actual values still exceeded levels permitted by standards. The study allow to indicate the operation fo postharvest technological process, which cause the most seed damage as well as gave quantita ive description of the losses occurred.

• Journal of Biosystems Engineering
• /
• v.26 no.4
• /
• pp.323-330
• /
• 2001

The regular maintenance and repair status of major farm machinery such as power tiller, farm tractor, rice transplanter and combine harvester etc., were surveyed and analyzed for the full-time farmers in order to get basic information for promoting farm machinery productivity. The survey was carried out through 209 farmers from 9 provinces. The results of this study can be summarized as follows; 1. The regular maintenance of farm machinery was conducted at repair shop(49.5%) or dealer agency(12.0%), and also conducted by farmers at their house(34.9%). 2. For the status on the cleanness or exchange times of engine oil, fuel filter and air cleaner, most farmers conducted fewer times than the necessary times. And, 5.3%, 7.7%, and 2.9% of surveyed farmers experienced breakdowns due to the insufficient cleanness or exchange oil, fuel filer, and air cleaner, respectively. 3. Most farmers(76.1%) recognized the necessity of farm machinery training or education, and they preferred one week for the training period, simple or easy maintenance for the training level, agricultural technical center or farm machinery manufacturer for the training agency. 4. Complete recognition of operation manual and sufficient maintenance before-, during-, and after-operation for the farm machinery can minimize the breakdowns, enlarge the endurance prevent the safety accidents, and promote productivity of farm machinery. And, these can be accomplished by the thorough training or education for agricultural machinery.