• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.67-73
• /
• 1992

This paper describes Hyundai's research and development work on a flexible fuel vehicle (FFV). The work on FFV has been conducted to evaluate its potential as an alternative to the conventional gasoline vehicle. Hyundai FFV described here can be operated on M85, gasoline, or any of their combinations, in which the methanol concentration is measured by an electrostatic type fuel sensor. For that operation, a special FFV ECU(Eletronic Control Unit) has been developed and incorporated in the FFV. The characteristics affecting FFV operation, such as FFV ECU control strategy and injector flow rate, have been investigated and optimized through the experiment. And various development tests have been performed in view of engine performance, durability, cold startability, and exhaust emissions reduction. The exhaust gas aftertreatment system consisting of manifold type catalyst and secondary air injection system shows good emission reduction performance including formaldehyde, and finally, the possibility of the FFVs as the low emission vehicles is evaluated by presenting NMOG(Non-Methane Organic Gases) levels with respect to M0 and M85. With these results, it is concluded that FFV can be a candidate for the low emission vehicles, but more works on its durability improvement is required.

• International Journal of Automotive Technology
• /
• v.2 no.2
• /
• pp.63-75
• /
• 2001

This paper describes the development of THC reduction technologies compliant with SULEV regulations. Technologies embodied by the developmental work include improvement of fuel spray atomization, quick warm-up through coolant control shut of, and acceleration of fuel atomization for the fast rise of cylinder head temp inside the water jacket as well as the improvement of combustion state. The technologies likewise entail reduced HC while operating in lean A/F condition during engine warm-up with the cold lean burn technology, individual cylinder A/F control for improvement of catalytic converting efficiency, after-treatment such as thin-wall catalyst, HC-adsorber and EHC and etc, through vehicle application evaluation in cold start. We carried out an experimental as well as a practical study against SULEV regulations, and the feasibility of adopting these items in vehicle was likewise investigated.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.1
• /
• pp.61-65
• /
• 2011

Recently, LCD (liquid crystal display) industry is needed to goods of high reliability and wide range temperature condition and it is interested in products for extremely cold condition without failure of light-up. In this experiment, we made the LED backlight unit for Automotive-navigation under the extremely cold condition. And for making this backlight unit, we used to eight side emitting type white LEDs with 3W high power LED. We could know that this backlight unit releases to 18,000 nit in 24W power consumption and start up voltage time is under the 1ms in the ambient temperature at -40.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.74-79
• /
• 2006

Good cold start characteristics are essential for satisfactory operation of fuel cell vehicles. In this study, the melting process has been numerically investigated for a water tank frozen in cold weather The 2-D model of the tank containing ice and plate heaters was assumed and the unsteady melting process of the ice was calculated. The enthalpy method was used for the description of the melting process, and a FVM code was used to solve the problem. The feasibility study compared with other experiment showed that the developed program was able to describe the melting process well. From the numerical analysis carried out for different wall temperatures of the pate heaters, some important design factors could be found such as local overheating and pressurization in the tank.

• The Korea Journal of Herbology
• /
• v.38 no.2
• /
• pp.9-16
• /
• 2023

Objectives : Many people use natural soap instead of commercially available bar type general soap for skin care. They tend to prefer cp (cold process) type soaps that go through a sufficient maturation process in formulation. The purpose of this study was to investigate the efficacy of PCPS (placenta cp soap). Methods : The researcher selected 36 subjects, 28 as the experimental group and 8 as the control group. I asked participants to wash their face twice a day in the morning and evening, and the period was set for 6 weeks. The researcher had the people who were selected as the control group use a commercially available foam cleanser, meanwhile the experimental group use PCPS. They performed a skin test before the start of the test, and the change status was continuously investigated after 2 weeks, 4 weeks, and 6 weeks after using the soap. Results : In the case of U zone oil and pores, there was a significant decrease and in the case of skin tone, there was a significant increase in the group of using PCPS. In T zone oil change, there was no significant effect in both the experimental group and the control group. Conclusion : In the case of PCPS, it is recommended to use it in the effect of reducing the size of pores and increasing skin tone, but it can reduce u-zone oil content.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.73.1-73.1
• /
• 2010

For the successful cold starting of a fuel cell engine, either internal of external heat supply must be made to overcome the formation of ice from water below the freezing point of water. In the present study, switchable vanadium oxide compounds as variable temperature-electrical resistance materials onto the surface of flat metallic bipolar plates have been prepared by a dip-coating technique via an aqueous sol-gel method. Subsequently, the chemical composition and micro-structure of the polycrystalline solid thin films were analyzed by X-ray diffraction, X-ray fluorescence spectroscopy, and field emission scanning electron microscopy. In addition, it was carefully measured electrical resistance hysteresis loop over a temperature range from $-20^{\circ}C$ to $80^{\circ}C$ using the four-point probe method. The experimental results revealed that the thin films was mainly composed of Karelianite $V_2O_3$ which acts as negative temperature coefficient materials. Also, it was found that thermal dissipation rate of the vanadium oxide thin films partially satisfy about 50% saving of the substantial amount of energy required for ice melting at $-20^{\circ}C$. Moreover, electrical resistances of the vanadium-based materials converge on an extremely small value similar to that of pure flat metallic bipolar plates at higher temperature, i.e. $T{\geq}40^{\circ}C$. As a consequence, experimental studies proved that it is possible to apply the variable temperature-electrical resistance material based on vanadium oxides for the cold starting enhancement of a fuel cell vehicle and minimize parasitic power loss and eliminate any necessity for external equipment for heat supply in freezing conditions.

• Nuclear Engineering and Technology
• /
• v.41 no.10
• /
• pp.1263-1274
• /
• 2009

Several experimental tests to simulate a reflood phase of a cold-leg LBLOCA of the APR1400 have been performed using the ATLAS facility. This paper describes the related experimental results with respect to the thermal-hydraulic behavior in the core and the system-core interactions during the reflood phase of the cold-leg LBLOCA conditions. The present descriptions will be focused on the LB-CL-09, LB-CL-11, LB-CL-14, and LB-CL-15 tests performed using the ATLAS. The LB-CL-09 is an integral effect test with conservative boundary condition; the LB-CL-11 and -14 are integral effect tests with realistic boundary conditions, and the LB-CL-15 is a separated effect test. The objectives of these tests are to investigate the thermal-hydraulic behavior during an entire reflood phase and to provide reliable experimental data for validating the LBLOCA analysis methodology for the APR1400. The initial and boundary conditions were obtained by applying scaling ratios to the MARS simulation results for the LBLOCA scenario of the APR1400. The ECC water flow rate from the safety injection tanks and the decay heat were simulated from the start of the reflood phase. The simulated core power was controlled to be 1.2 times that of the ANS-73 decay heat curve for LB-CL-09 and 1.02 times that of the ANS-79 decay curve for LB-CL-11, -14, and -15. The simulated ECC water flow rate from the high pressure safety injection pump was 0.32 kg/s. The present experimental data showed that the cladding temperature behavior is closely related to the collapsed water level in the core and the downcomer.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3317-3322
• /
• 2007

THC(Total Hydrocarbon) emissions during cold start and warm-up phase constitute the majority of THC emissions during the FTP-75 mode. As the basic approach to improve the emission performance of Gasoline engine during transient phase, the effect of spark timing retard from MBT on THC emission characteristics is studied by engine test using a Fast response Flame Ionization Detector(FFID). A cyclic analysis of the combustion process shows that high THC emissions are produced first few cycles during the transient phase. This paper presents the results of engine performance and emission of Gasoline engine with various spark timing. consequently, This paper was focused on the combustion phenomena with various spark timing during transient phase which was analyzed by Fast response Flame Ionization Detector (FFID) equipment to measure the cyclic THC emission characteristics.

• Proceedings of the Korean Information Science Society Conference
• /
• 1999.10b
• /
• pp.69-71
• /
• 1999

정보의 양이 많아질수록 사용자가 자신이 원하는 정보를 찾는 작업은 많은 시간과 노력을 요구하게 된다. 이러한 시간과 노력을 줄이기 위해 정보 필터링 시스템이 제시되었고, 정보검색과 자연언어처리 등을 이용한 많은 방법들이 연구되었다. 그러나 이러한 접근방법들은 모두 사용자에게 새로운 정보요구가 생긴 경우 이를 지능적으로 대처하지 못하는 Cold-Start 문제를 안고 있다. 이를 극복하기 위해 협동 정보 필터링 시스템이 등장하였다. 이러한 협동 정보 필터링 시스템은 같은 관심도를 가지는 사람들로 공동체를 형성하기 위해 사용자로부터 관심도를 명시적으로 나타낼 것을 요구하는 등 사용자가 직접 필터링 시스템을 학습시켜야 하는 문제점을 가지고 있다. 본 논문에서는 이러한 문제를 해결하기 위해 사용자들의 선호도를 담고 있는 사용자 프로파일의 유사성을 기반으로 한 공동체 형성 방법을 제안한다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.115-124
• /
• 2002

The optimum design of auto-catalyst needs a good compromise between the pressure drop and flow distribution in the monolith. One of the effective methods to achieve this goal is to use the concept of radially variable cell density. However, there has been no study of evaluating the usefulness of this method on light-off catalyst. We have computationally investigated the effectiveness of variable cell density technique applied to the light-off catalyst using a three-dimensional integrated CFD model. in which transient chemical reacting calculations are involved. Computed results show that variable cell density technique can reduce the accumulated emissions of CO and HC during the early 100sec of FTP cycle by 86.78 and 80.87%, respectively, The effect of air-gap between the monoliths has been also examined. It is found that air-gap has a beneficial effect on reducing pressure drop and cold-start emissions.