• Journal of the Korean Society of Safety
• /
• v.29 no.3
• /
• pp.1-7
• /
• 2014

In this study, for the evaluation of the static and fatigue joining strength of the joint, the geometry of the cross-tension specimen was adopted. The specimens were produced with optimal joining force and fatigue life of the clinch joint specimens was evaluated. The material selected for use in this study was cold rolled mild steel (SPCC) with a thickness of 0.8 mm. The maximum tensile load was 708 N for the specimen with single point. The fatigue endurance limit (=42.6 N) per point approached to 6% of the maximum tensile strength at a load ratio of 0.1, suggesting that the joints are vulnerable to cross-tension loading during fatigue. Compared to equivalent stress and maximum principal stress, the SWT fatigue parameter and equivalent strain can properly predict the current experimental fatigue life. The SWT parameter can be expressed as $SWT=2497.5N^{-0.552)_f$.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.7
• /
• pp.36-43
• /
• 1998

Surface roughness of cold rolled steel sheet as well as the coating technique itself is quite important in obtaining high image clarity of electronic products and car outer panels. Especially, surface characteristics of steel sheet have acquired increasing attention from the steel and automotive industries. While the influence of such characteristics on paintability formability and painted surface appearance is important in defining steel surface requirements for automotive industries. Therefore this paper is dedicated primarily to the issue of paint appearance and reviews for improvement of roughness and peak count about the surface of work roll for the actual temper mill. The conclusions were obtained as follows ; 1) Roughness and peak count about the surface of steel sheet is strongly affected by surface condition of work roll. 2) The electro-discharge textured roll has more uniform roughness distribution than shot blasted roll and it's painted appearance of steel sheet has more improvement than that of the shot blasted because it has more harmonic wave roughness, and the higher peak count of surface roughness.

• Transactions of Materials Processing
• /
• v.10 no.2
• /
• pp.160-166
• /
• 2001

Uniaxial necking is studied for steel sheets with initial anisotropy. The state of anisotropy is continuously altered by subsequent tensile deformation at angles to the rolling direction. The orientations of orthotropy axes are changed before the onset of necking. A simple hardening rule which incorporates the rotations of orthtropy axes is proposed and the necking strains are predicted at angles to the rolling direction. Predicted results show good agreement with the experiments.

• Journal of the Korean Society of Safety
• /
• v.27 no.5
• /
• pp.42-48
• /
• 2012

Peel-tension fatigue experiments were conducted for investigating on fatigue strength of mechanical press joints of SPCC steel sheet used in the field of the automobile industry. In addition, finite element method analysis on the peel-tension specimen was conducted using HyperMesh and ABAQUS softwares. The cold rolled mild steel was used to join the T-shaped peel-tension specimen with a button diameter of 5.4 mm and a punch diameter of 8.3 mm. The fatigue limit load amplitude was found to be 112.4 N at the number of cycles 106, indicating that the ratio of fatigue limit load to static peel-tension strength was about 8%. This value suggests that the mechanical press joint is highly vulnerable to peel-tension load rather than to tensile-shear load, considering that the ratio of fatigue limit load to static tensile-shear strength was about 43%. Fatigue failure mode was found to be interface-failure mode.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.389-392
• /
• 2005

In the modern days, a galvannealed sheet steel(GA) instead of a cold rolled steel sheet has been widely used as an alternative to extend the life of automotive body. Accordingly, the mechanical properties of GA for automobiles were taken Into account and studied by comparing with the temperature variation on annealing in this study. To clarify the effect of surface features in the mechanical properties of GA, the several tests such as nanoindentation and FE-analysis were executed. For this goal use is made of the method of neural networks. The developed neural networks apply also to obtain reliable mechanical properties of the thin films. Load-displacement curve was computed by the analysis procedure and compared with experimental results.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.1807-1818
• /
• 1991

The frictional characteristic of Zn-Ni electrogalvanized steel sheet was investigated by experimental procedures. To clarify the effect of surface property on the frictional characteristic of Zn-Ni coated steel sheet, Micro-hardness test, SEM analysis and X-ray diffraction analysis were carried out. Coefficients of friction for various stamping lubricant and Ni content in coated layer were measured by a draw bead friction test. The results show that frictional characteristic is very sensitive to Ni content of coated layer and depends on stamping lubricant. For Ni content less than about 11%, selection of proper lubricant is necessary to obtain low coefficient of friction in Zn-Ni coated steel sheet such as in case of cold rolled steel sheet.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.2
• /
• pp.108-114
• /
• 1998

Development on the mechanical properties of steel sheet for the automobile body panel is very important in the BAF(Batch annealing furnace) annealing process. Because of the heat treatment method in the BAF, mechanical properties was decided on the heat treatment method of the coil. So, we tested on the development of mechanical properties according to heat treatment method at the annealing furnace using the Ax(H$_2$75%, $N_2$25%) atmospheric gas and the HNx(H$_2$4%, $N_2$96%) atmospheric gas. As a result of several investigations. We confirmed the following characteristics ; mechanical properties was changed under the influence of the annealing cycle, the heat treatment method and the atmospheric gas. And, elongation in the HNx BAF was better than the Ax BAF. Finally, most important thing in the BAF is using of proper annealing cycle in order to get a good quality.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1474-1486
• /
• 1990

The frictional characteristics of galvanized sheet steels(GA, EG, EGF, EGN) for automobiles were studied and compared with that of cold rolled sheet steel. A draw bead tester which simulates metal flow through a draw bead in stamping die face was used to measure coefficients of friction of galvanized sheet steels for four kinds of lubricants. Stamping formability of galvanized sheet steels for quarter outer panel was examined. The results show that stamping formability and friction characteristics were mainly influenced by the nature of zinc coating, surface roughness and micro hardness of coated layer, and proved to be very sensitive to the lubricant used.

• Journal of the Korean institute of surface engineering
• /
• v.28 no.5
• /
• pp.289-299
• /
• 1995

The effects of phosphate coating have been studied on physical properties and corrosion resistance of painted aluminum alloy sheet for automobile body. The physical properties (surface roughness, paint adhesion, impact resistance and pencil hardness) and corrosion resistance(cyclic corrosion and filiform corrosion) were investigated. Phosphate coatings enhanced the physical properties of painted Al alloy sheet, especially paint adhesion after the 240hours water immersion test. Phosphate coating also markedly improved the resistance for cyclic corrosion and filiform corrosion of painted cold rolled steel and Zn-Ni plated steel sheet as well as painted Al alloy sheet. The corrosion resistance of painted Al sheets was varied with the concentration of free fluoride ion and metal additives like Ni and Mn in the phosphating bath. A maximum corrosion resistance was obtained at about 300ppm of fluoride ion and additives of Ni and Mn obviously increased the corrosion resistance of painted specimens.

• Journal of Korean Institute of Industrial Engineers
• /
• v.25 no.4
• /
• pp.476-489
• /
• 1999

This paper is concerned with the deployment of core technologies for automotive steel sheets, based on the structural change of global market. The main tasks of automotive industry are to ensure the energy consumption, environmental regulations, and driving safety. With social and legal requirements, this study analyzes the market creation processes with technological innovations for hot rolled, cold rolled and galvanized steel sheets during the 20th century. It has been proven that the leading country in the steel industry was also that in the automotive. The purchaser-supplier relations of sheet materials are then patternized in the regional markets of the United States and Japan, who share nearly 50% of market in the world. According to the paradigm shift of globalization, the balance of power in Porter's 5 forces has been moved to the buyers', and both industries pursue Win-Win strategies such as the PNGV(Partnership for a New Generation of Vehicles ) and design-in system with the competition.