• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.3
• /
• pp.219-223
• /
• 2011

Rhenium-Iridium(Re-Ir) thin films were deposited onto the tungsten carbide(WC) molding core by sputtering system. The Re-Ir films were prepared by multi-target sputtering with iridium, rhenium and chromium as the sources. Argon and nitrogen were inlet into the chamber to be the plasma and reactive gases. The Re-Ir thin films were prepared with targets having atomic percent of 3:7 and the Re-Ir thin films were formed with 240 nm thickness. The Re-Ir thin films on tungsten carbide molding core were analyzed by scanning electron microscope(SEM) and surface roughness. Also, adhesion strength and coefficient friction of Re-Ir thin film were examined. The Re-Ir coating technique has been intensive efforts in the field of coating process because the coating technique and process have been their feature, like hardness, high elasticity, abrasion resistance and mechanical stability and also have been applied widely the industrial and biomedical areas. In this report, tungsten carbide(WC) molding core was manufactures using high performance precision machining and the efforts of Re-Ir coating on the surface roughness.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.11
• /
• pp.736-739
• /
• 2014

In this paper, we propose a enhanced anti-corrosion property of the ground system by coating the CNT/PVDF composite film on it. Polymer material used for preventing the corrosion of ground system is polyvinylidene fluoride (PVDF), and conducting filler for obtaining conductivity of the composite film is multi-walled carbon nanotubes (MWCNTs). The MWCNTs were dispersed in the organic solvent of methyl ethyl ketone 2-butanone (MEK) with different concentration ratios, and the PVDF was solved in the MEK solvent with constant concentration ratio of 1 wt%. The CNT/PVDF composite solution was perpared by mixing and re-dispersing the CNT solution and the PVDF solution. Finally, the CNT/PVDF composite films were fabricated by the spray coating method using the above composite solution. Electrical conductivity, surface states, and anti-corrosion property of the CNT/PVDF composite films coated on the Cu substrate were evaluated. We found that the CNT/PVDF composite film showed relatively low resistance, hydrophobic surface state, and chemical stability. Consequently, we could improve the anti-corrosion property and maintain the electrical conductivity of the ground system by coating the CNT/PVDF composite film on it.

• Journal of the Korean Society of Safety
• /
• v.20 no.1 s.69
• /
• pp.18-23
• /
• 2005

This study deals with the friction and wear characteristics of C-N coated SCM415 steel. The PSII(plasma source ion implantation) apparatus was built and a SCM415 test piece with steel substrate was treated with carbon nitrogen by this apparatus. The composition and structure of the surface layer were analyzed and compared with that of PVD(physical vapor decomposition) coated TiN layer. It was found that both of friction coefficient of C-N coating and TiN coating decreased with increasing load, however, C-N coating showed relatively lower faction coefficient than that of TiN coating. The micro-vickers hardness of C-N film is 3200 Hv, which is $32\~43\%$ higher than that of TiN film. The critical load of C-N film is 52N, which is $25\%$ higher than that of TiN film. The hardness of C-N film fabricated by Plasma ion implantation is $61\~70\%$ higher than that of base material, and faction coefficient is $14\~50\%$ lower than that of base material. It is also interesting to note that the friction was changed from adhesive wear mode to light oxidizing wear mode.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.5
• /
• pp.205-211
• /
• 2022

The Granule Spray in Vacuum (GSV) process is a method of forming a dense nanostructured ceramic coating film by spraying ceramic granules on a substrate at room temperature in a vacuum. In the Granule Spray, the granules made by agglomerating particles with the size from submicrometer to micrometer can be sprayed into the substrate. Once the granules were squashed upon collision with the substrate, they become several dozens of nanometer-sized crystals in vacuum process. The zirconia of the monoclinic phase transform into tetragonal phase at 1150℃. At this time, its volume is changed by about 6.5 %. For this reason, it is widely held that it is difficult to acquire a compact of monoclinic zirconia sinter. In this study, the effect of particle treatment temperature and standoff distance on the substrate of zirconia granules were investigated in GSV. Also, particle treatment temperature, standoff distance, coating efficiency, and microstructure of the film were considered in forming the monoclinic zirconia coating film in GSV without any heating process. The deposited films exhibited monoclinic zirconia phase without any other detectable phase by X-ray diffractometer (XRD).

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.31.2-31.2
• /
• 2009

In this research, single walled carbon nano-tube film was manufactured with spray coating method on glass for application as transparent heat element. SWNTs solution to be used for spraying is obtained by dispersion of 0.01 wt% purified SWNTs in dimethylformamide (DMF) solution through ultrasonification and centrifugation. The transmittance and sheet resistance of SWNTs film were determined by the number of spray injection. Manufactured SWNTs film will have sheet resistance range of $200\;\Omega/\square-900\;\Omega/\square$ at transmittance range of 70-90 %. Heat generation characteristic of SWNTs film was measured by applying constant DC voltage of 15V. The result confirmed that SWNTs film with sheet resistance of $200\;\Omega/\square$ reaches surface temperature of $80^{\circ}C$ within several seconds. In addition, PET coating film was coated on top of the SWNTs film by using laminator in order to solve weak adhesive property of the spray coated SWNTs film on the substrate as well as to maintain its electrical and optical properties.

• Korean Journal of Materials Research
• /
• v.17 no.8
• /
• pp.447-451
• /
• 2007

We investigated the dependence of the various annealing conditions and thickness ($6\sim45nm$) of the Ti-doped $Al_2O_3$ coating on the electrochemical properties and the capacity fading of Ti-doped $Al_2O_3$ coated $LiCoO_2$ films. The Ti-doped-$Al_2O_3$-coating layer and the cathode films were deposited on $Al_2O_3$ plate substrates by RF-magnetron sputter. Microstructural and electrochemical properties of Ti-doped-$Al_2O_3$-coated $LiCoO_2$ films were investigated by transmission electron microscopy (TEM) and a dc four-point probe method, respectively. The cycling performance of Ti-doped $Al_2O_3$ coated $LiCoO_2$ film was improved at higher cut-off voltage. But it has different electrochemical properties with various annealing conditions. They were related on the microstructure, surface morphology and the interface condition. Suppression of Li-ion migration is dominant at the coating thickness >24.nm during charge/discharge processes. It is due to the electrochemically passive nature of the Ti-doped $Al_2O_3$ films. The sample be made up of Ti-doped $Al_2O_3$ coated on annealed $LiCoO_2$ film with additional annealing at $400^{\circ}C$ had good adhesion between coating layer and cathode films. This sample showed the best capacity retention of $\sim92%$ with a charge cut off of 4.5 V after 50 cycles. The Ti-doped $Al_2O_3$ film was an amorphous phase and it has a higher electrical conductivity than that of the $Al_2O_3$ film. Therefore, the Ti-doped $Al_2O_3$ coated improved the cycle performance and the capacity retention at high voltage (4.5 V) of $LiCoO_2$ films.

• Korean Journal of Materials Research
• /
• v.21 no.1
• /
• pp.8-14
• /
• 2011

To improve the chemical stability of metal, the ceramic coatings on metallic materials have attracted interest from many researchers due to the chemical inertness of ceramic materials. To endure strong acids, SiOC coating on metal substrate was carried out by dip coating method using 20wt% polyphenylcarbosilane solution; SiC powder was added to the solution at 10wt% and 15wt% to improve the mechanical properties and to prevent cracks of the film. Thermal oxidation as a curing step was carried out at $200^{\circ}C$ for crosslinking of the polyphenylcarbosilane, and the coating samples were pyrolysized at $800^{\circ}C$ under argon to convert the polyphenylcarbosilane to SiOC film. The thicknesses of the SiOC coating films were $2.36{\mu}m$ and $3.16{\mu}m$. The quantities of each element were measured as $SiO_{1.07}C_{6.33}$ by EPMA, and it can be confirmed that the SiOC film from polyphenylcarbosilane was formed in a manner that was carbon rich. The hardness of the SiOC film was found to be 3.2Gpa through nanoindentor measurement. No defect including cracks appeared in the SiOC film. The weight loss of the SiOC coated stainless steel was within 2% after soaking in 10% HCl solution at $80^{\circ}C$ for one week. From these results, SiOC coating shows good potential for application to protect against severe chemical corrosion of stainless steel.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.22 no.2
• /
• pp.101-110
• /
• 2004

The local surface strength variation of coated papers were measured at various speeds on a number of coated paper samples to study the effects of speed and ink tack on coating pick. Coating pick phenomenon is observed in an ink transfer variation curve as a decrease in the slope of the curve. On the other hand, it causes an actual decrease in net ink transfer to paper with an increase in speed. The effect of speed on coating pick depends on ink tack, ink film thickness and surface properties of coating layer formation of paper. A novel device to measure the surface strength can rate the coating paper in a different order. Comparison are made between dry test of coating paper pick and wet coating pick test of printing in IGT printability tester. Coating formulation is the main key to prevent from coating pick. The binder level increases, the coating pick and the slop decrease. The piling on blanket in printing is a problem when the coating pick is occur on a local area rather than average surface strength of coated papers.

• Food Science and Preservation
• /
• v.12 no.4
• /
• pp.323-328
• /
• 2005

This study were investigated to analyzed an optimum preparation condition of coating film and its antimicrobial activity on pathogenic and deteriorative bacteria to obtain fundamental data for development of active packaging film using antimicrobial peptide, polysine. In the preparation conditions of coating film, antimicrobial activity was depending on the concentration of polylysine and polyamide respectively, and relatively high activity was obtained in the film prepared with more than $1.0\%$ (w/v) of polylysine, $40\%$ (w/v) polyamide, and more than $50\;{\mu}m$ of film thickness. Concentration of polylysine migrated from coated film to distilled water was reached at the maximum concentration, about 20 ppm after 3 days and in equilibrium after 7 days of soaking in sterilized water. An antimicrobial activity of coated film showed bactericidal effect of about $10^5\;CFU/mL$ comparing with the control against Bacillus cereus having $4.8{\times}10^5\;CFU/mL$ of initial viable cell numbers, and of about $10^2\;CFU/mL$ comparing with the control against Klebsiella pneumoniae having $6.8{\times}10^5\;CFU/mL$ of initial viable cell numbers. Consequently, it was revealed that polylysine coating film has a potential of applicable possibility as antimicrobial packaging film.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1340-1342
• /
• 1998

The diamond-like carbon(DLC) film, as an antireflection layer, is coated on a commerically used Ge window. DLC films are deposited by using an rf(13.56 MHz) plasma CVD. The optimal value of thickness and refractive index of DLC layer has been determined from the computer simulation. IR-transmittances of DLC-coated Ge windows are estimated by measuring FTIR spectra in the wavelength range of$ 2.5{\sim}25{\mu}m$. By coating the DLC film on one side of the Ge window, the transmittance measured at a wavelength of $10{\mu}m$ is about 60 %, while that of the bare Ge is lower than 50 %. Also, a higher transmittance up to about 90 % is obtained by coating the DLC film on both sides of the window. It may be suggested that the further improvement of the IR-transmittance can be achieved by more precisely controlling the thickness and the refractive index of DLC layer and also by adopting various muliti-layer antireflection structures.