• Journal of the Korean Wood Science and Technology
• /
• 제10권2호
• /
• pp.22-27
• /
• 1982

This experiment was carried out to evaluate the results of fire retardancy of sealer coated plywood by Building material combustibility tester and Inclined panel tester. At this study, weight loss percentage, flame exhausted time, burning point and smoke yield coefficient were examined. The findings of this study lead to conclusions as listed below. 1. It was obvious that weight loss percentage and flame exhausted time of Inclined panel tester had more remarkable tendency than those of Building material combustibility tester. 2. Burning point was determined by Inclined panel tester while smoke yield coefficient by Building material combustibility tester. 3. Weight loss percentage decreased remarkably with proportion to the increase of sealer coated amount during 5 minutes burning. 4. Flame exhausted time decreased with proportion to the increase of sealer coated amount during 3 minutes burning. 5. Burning point indicated increasing tendency with proportion to the increase of sealer coated amount. 6. Smoke yield coefficient of urea scaler showed definite inclination decreasing with the increase of sealer coated amount.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.176-179
• /
• 2000

In the recognition of the gases using the quartz crystal microbalance (QCM) coated with the film materials, it is important to obtain the recognition ability of gases, and the stability of film coated above the QCM. Especially, the thickness of film coated above the QCM is decreased according with the using circumstance and time of QCM gas sensor. Therefore, the sensing chararcteristics of film is changed with these. In this paper, we coated the lipid PC (Phosphatidyl Choline) materials varing with the blended amount of PVC(Poly Vinyl Chloride) and solution (Tetra Hydrofan:THF) above QCM to obtain the stability of lipid PC film. QCM gas sensors coated with film materials were measured the frequency change in the chamber of stationary gas sensing system injected 1-hexane, ethyl acetate, ethanol and benzene of $20{\mu}{\ell}$, respectively. We obtained the principal component analysis (PCA) from the frequency change due to the absorption of gas. Also, we measured the degradation characteristics of QCM gas sensor to show the properties of stability.

• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.81-86
• /
• 2010

This paper investigated into process characteristics of AlTiN coated layers for machining to the direction of upper and lower in plastic mold material (KP-4) with the cemented carbide ball endmill with the diameter of 8mm coated AlTiN layers (1~4) step by step using machining center. The material used in experiments was KP-4 that was machined by three types of inclined angles; $15^{\circ}$, $30^{\circ}$ and $45^{\circ}$ As estimated mechanical properties of AlTiN coated layers, it was shown the most result in the condition of three layered coating that the coating that the coating depth, the hardness of the coated layer and the surface roughness of the coated layer were $13{\mu}m$, Hv 3027.3 and $0.042{\mu}m$, respectively. The cutting component was better at the condition of upper direction than that of lower direction in all experimental conditions and indicated to be less which the bigger angle of the material was increased the effective diameter of the tool.

• 수산해양교육연구
• /
• 제22권4호
• /
• pp.501-507
• /
• 2010

The ceramic contained paint was made to replace the lead sinker for gill-net with coated lead sinker. The ceramic contained paints were coated in various conditions on the lead sinker with 19g of weight and the optimal coating condition was studied. The adaptability of the coated lead sinker was checked through the anti durability test and fishing operation with gill-net. The case of "Main material 70 wt% + Urethane thinner 30 wt% (Main material 700 $m{\ell}$ + Thinner 300 $m{\ell}$)" showed the best in the coating characteristics depending on the combination ratio of the ceramic paint contained. The coated lead sinker dried at $100^{\circ}C$ inside oven was superior to the drying in the room temperature in its surface glossiness and anti durability and faster drying time than the one dried in normal temperature. The quadruple layers of coating on lead sinker with 4 times of dipping and drying application showed the super anti durability in the coating characteristics depending on the frequency of dipping. When press is applied to the coated lead sinker, the coated layer is not detached from the sinker. In addition, the coated lead sinker was not damaged or peeled at the fishing operation about 2 months in various depths within 50m and by the materials at the bottom (sand, stone and gravel stone) and it was in good condition.

• Tribology and Lubricants
• /
• 제15권1호
• /
• pp.29-38
• /
• 1999

In recent years, the tribological behavior of coated ceramic material has been the issue of much interest. Particularly, the understanding of the tribological performance of thin film under light load is important for its potential in applications of MEMS. The friction and wear behavior of ceramic material that occur at light load depends on several factors such as surface roughness, contact area and material properties. In this work, the tribological behavior of coated silicon under light load and low speed was investigated. Particularly, the effects of coated materials, humidity and undulated surface were also studied. The results show that the effect of humidity on fiction was influenced by the apparent area of contact between the two surfaces. Also both adhesive and abrasive wear occurred depending on the sliding condition. Finally, undulations on the silicon wafer were found to be effective in trapping wear particles and resulted in the reduction of friction.

• 한국전기전자재료학회논문지
• /
• 제22권12호
• /
• pp.1067-1072
• /
• 2009

YBCO coated conductor is named by second generation superconductor tapes. It is different with first generation superconductor tapes. YBCO coated conductor's specific difference with Bi-2223/Ag tape is more strong mechanical durability. This is important role to apply to superconducting machines. For mechanical transforming of YBCO coated conductors, we are using the well designed former. The merit of transformation is several. First, we vary the superconducting characteristics according to mechanical stress. Second, we reduce the volume of superconductor, so we achieve reducing the volume of superconducting machines. On this study, we experiment the transporting current characteristics of one types YBCO coated conductor. YBCO coated conductor with Ie of 70 A and voltage grade of 0.6 V/cm were connected to spiral former to conduct current application test.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.82-85
• /
• 2003

In this paper, we present the analysis of electromagnetic scattering from arbitrarily shaped three-dimensional conducting objects coated with a dielectric material. The integral equation treated here is the combined field integral equation. Numerical results of radar cross section for coated conducting structure are presented and compared with other available solutions.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.211-211
• /
• 2009

YBCO coated conductor can change the stabilization layer for purpose and it leads advantages in Improvement of tape's critical properties and Application. Such properties rise possibility of using YBCO coated conductor for Superconductor Fault Current Limiter, therefore, we investigate changing properties under over current condition and limiting characteristics. In this study, YBCO coated conductor's current limiting characteristic stainless steel stabilization layer under condition of changing conductor's insulating layer. Consequently, the resistance followed insulating layer so we know that limiting characteristics.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 춘계학술대회 논문집
• /
• pp.12-12
• /
• 2010

The hall probe measurement system was used to measure the critical current distribution of superconducting coated conductor. The system consists of reel to reel moving apparatus, 7 array hall probe, a rotary encoder and permanent magnet. The magnetic field profile across the width of superconducting coated conductor using Bean's critical state model was calculated. The effect of various parameters of the formulas on the magnetic field distribution and the effect of shape and size of artificial defects, which were formed on the surface of SmBa2Cu3O7-d(SmBCO) coated conductor using laser marking system, on the hall probe magnetic field signal of the hall probe measurement system was investigated.

• 전기화학회지
• /
• 제6권2호
• /
• pp.103-112
• /
• 2003

리튬이차전지 음극활물질로 사용되는 합성흑연입자에 여러종류금속을 코팅하여 그 전기화학적특성을 조사하였으며, 구체적인 코팅방법으로는 가스분산스프레이 코팅법을 적용하였다. 본 연구범위내에서 금속을 코팅한 입자로 제조된 전극은 충방전시 형성되는 계면저항을 감소시킴으로서 결과적으로 원시료에 비해서 높은 방전용량을 나타내었다. CV실험을 통해서 은과 주석은 리튬과의 합금반응을 확인할 수 있었으나, 2.5 중량$\%$ 이하의 낮은 코팅량을 고려했을 때, 높은 분산도를 지닌 금속 물질의 코팅을 통한 전극 활물질 표면의 균일한 전도도의 증가가 주요원인인 것으로 사료되었다. 단일계 금속으로 코팅하였을 경우 은코팅한 전극활물질이 가장 높은 방전용량과 사이클특성을 나타내었고, 은을 기본으로 하는 이성분계에서는 은-니켈전극이 가장 높은 고율특성을 나타내었다.