• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.3
• /
• pp.31-37
• /
• 2011

The purpose of this study is to investigate cutting characteristics and wear behavior in SCM440 steel with different cutting tools, CBN(Cubic Boron Nitride) and coated CBN. During the test coated CBN tool especially with TiAlN showed better wear resistance behavior than orginal CBN tools. In the interrupted cutting condition, axial groove affected tool surface with impact force during the turning operation. For advantageous turning parameter in the interrupted process it is recommendable that lower speed. Also surface roughness showed better behavior in the coated CBN tool conditions than normal CBN conditions. Mainly this is caused by reduced friction between material and tool surface with coated layer.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.107-113
• /
• 1996

This paper presents the experimental results on the cutting performance and wear characteristics of CBN ball end-mill. The influence of cutting fluids and rake angles on the tool performance is reported. It i found that the neat cutting oil is beneficial to obtain good surface roughness and 30 .deg. of rake angle gives the minimum tool wear. The microscopic investigations reveal that the coated carbide endmills wear by fracture whereas the CBN endimills wear by attritious mode.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.8
• /
• pp.73-81
• /
• 1997

The hard turning process defined as a single point turning of materials harder than $H_{R}$C 58 differs from conventional turning because of hardness of the work materials and cutting toos needed in the process. In hard turning, tool life is very short, of the order of a few minutes, during which the cutting tool is subjected to the extremes of stress and temperature. In this regard, it is well known that CBN tool is proper for this process in spite of expensive cost. In this research, we studied the feasibility of the use of the low cost cutting tool such as a aTiN coated tool. To this end, a new cooling system was designed with an air-oil method for reducing tool temperature, which is based on the principle of air vortex flow. That is, the outlet temperature of the air becomes aver 20 .deg. C lower than atmosphere temperature by entering pressurized air of 5kgf/c $m^{2}$ into the inlet. This cooled air ejected to the top of the cutting tool lowered tool temperature, which reduced the wear of a TiN coated tool by the 30% of CBN tool life with respect to the same cutting length.h.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.1
• /
• pp.9-14
• /
• 2013

In recent years, high hardness steel is used for most of the material in many areas including aircraft, nuclear power, space exploration and automotive parts. Low CBN tools are widely used in industrial field which can effectively process high hardness steel of HRC 45 or harder. The results of this study demonstrated, when high hardness steel, SCM440 is turned with Low CBN tools coated with TiN and TiAlN coatings respectively, that both the thrust force and cutting force tends to increase with more increase in cutting force than thrust force, as the feed rate increases at constant cutting speed. In addition, the size of the cutting force and thrust force does not change with the increased cutting speed at the same feed rate, but the tool life is reduced if the cutting speed is increased to shorten the machining time. Therefore, it is recommended to limit the cutting speed at 250 m/min maximum or less. Furthermore, comparing the cutting force of the three tools at the same cutting condition, Tin coating tool showed the smallest cutting force and Low CBN was the next, and the TiAlN coating tools showed the largest cutting force.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.6
• /
• pp.312-324
• /
• 2008

In this study, the functional property as a super abrasive material was secured for CBN powder by the electroless Ni-P plating on the surface of the particle. The plating solution has been prepared to control the surface morphology by regulating surfactants and process conditions. The effects of processing parameters on the surface morphology of CBN powder was discussed. The results are summarized as follows; A stable plating tendency was achieved from 1 hour after quantitatively dropping reducing agent. It was observed that more than 50% of the weight gain was obtained by Ni-P coating on the surface of CBN super abrasive powder. The morphology of the Ni-P coating layer is consisted of botryoidal and spiky type and it could be controlled by regulating processing parameters. Superior characteristic in terms of surface morphology was found in the nonionic surfactant XL-80N. It was found that XL-80N considerably decreased surface tension of CBN powder and Ni-P alloy surface then enhance wettability as well as plating rate. Metal coated CBN powder as a raw material of resin bond wheel has been developed through this investigation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.5
• /
• pp.8-12
• /
• 2012

Recently, a wide range of industrial production area has a competitive advantage through cost reduction. Moreover with the development of industrial technology, base material and cutting tool help the machining technology. But most of the machining enterprises have not hold the R&D facilities and human resources. This mainly disturbs the industrial development and th increase of production efficiency. Especially in the interrupted machining process, it showed different behavior with continuous machining process. So it needs to research and develop the tool life and tool wear mechanism analysis.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.4
• /
• pp.27-35
• /
• 1998

Ni-based heat resisting alloys are commonly used for high temperature applications such as in aircraft engines and gas turbines. In this work, the machinability of Nimonic 263 alloy is investigated with respect to optimum tool type and cutting conditions for both continuous and discontinuous machining as well as weld region. Among the five types of tools tested, K25 tool experienced the least of damage in machining the weld region. Furthermore, despite their superior high temperature hardness, Si-Al-O-N and CBN tools peformed poorly in machining Nimonic 263.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.4 s.175
• /
• pp.900-906
• /
• 2000

Ceramic, PCD and CBN tools are available for the difficult-to-cut-materials such as hardened carbon tool steel, stainless steel, Inconel 718 and etc. Ceramic tools are likely to be chipped and abruptly broken before the appearance of normal wear in turning. Ceramic tools are suitable for continuous in turning, not for intermittent in milling. In this study, TiN/TiCN multi-layer coated ceramic tools were found to restrain the chipping, breaking and early fracture and to increase the critical cutting speed owing to TiN/TiCN multi-layer coating in Arc Ion Plating of PVD method.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.4
• /
• pp.123-129
• /
• 1998

Ceramic and CBN tools are available for the difficult-to -cut-materials such as hardened carbon tool steel. stainless steel and etc. Ceramic tools are suitable for continuous turning cut, not for intermittent milling cut. Ceramic tools are likely to be chipped and abruptly broken before the appearance of normal wear in turning. In this study, TiN coated ceramic tools were found to restrain the chipping, breaking and early fracture and to increase the critical cutting velocity owing to TiN coating in PVD method.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.1
• /
• pp.96-101
• /
• 2000

Ceramic, PCD and CBN tools are available for the difficult-to-cut-materials such as hardened carbon tool steel, stainless steel, Inconel 718 and etc.. Ceramic toolsare likely to be chipped and abruptly broken before the appearance of normal wear in turning. Ther2efore ceramic tools are suitable for continuous cut in turning not for intermittent in milling. In this study, TiN/TiCN multi-layer coated ceramic tools were found to restrain the chipping, breaking and early fracture and to increase the critical cutting speed owing to TiN/TiCN multi-layer coating in Arc Ion Plating of PVD method.