• 한국도로학회논문집
• /
• 제19권6호
• /
• pp.23-30
• /
• 2017

PURPOSES : In this paper, the applicability of DEM to a coarse graining method was evaluated by simulating a series of minicone tests for cement paste. METHODS : First, the fundamental physical quantities that are used in a static liquid bridge model were presented with three basic quantities based on the similarity principle and coarse graining method. Then, the scale factors and surface tensions for six different sizes of particles were determined using the relationship between the physical quantities and the basic quantities. Finally, the determined surface tensions and radii were utilized to simulate the fluidal behavior of cement paste under a minicone test condition, and the final shape of the cement paste with reference DEM particle radii was compared with the final shape of the others. RESULTS : The simulations with adjusted surface tensions for five different radii of particles and surface tension showed acceptable agreement with the simulation with regard to the reference size of the particle, although disagreement increases as the sizes of the particle radii increase. It seems reasonable to increase the particle radii by at least 0.196 cm considering the computational time reduction of 162 min. CONCLUSIONS : The coarse graining method based on the similarity principle is applicable for simulating the behavior of fluidal materials when the behavior of the materials can be described by a static liquid bridge model. However, the maximum particle radius should be suggested by considering not only the scale factor but also the relationship of the particle size and number with the radius of the curve of the boundary geometry.

• 한국대기환경학회지
• /
• 제20권6호
• /
• pp.833-838
• /
• 2004

The analysis of Pb in both PM$_{2.5}$ and PM$_{10}$ fraction of aerosols was made consecutively for every spring season during four year period of 2001 through 2004. To diagnose the impact of the Asian Dust (AD) on metal concentration levels, we compared our Pb measurement data after dividing the whole data sets into AD and NAD period. The results of our analysis indicated that the concentrations of coarse particles increased significantly during the AD period, whereas an increase in the fine counterpart was of moderate degree. However, when Pb concentrations between AD and NAD were compared, the patterns were quite different. From all particle fractions, the Pb concentrations of NAD were slightly or moderately higher than those of AD. The overall results of our study suggest that an increase in particle concentrations during the AD period can cause a rather slight reduction in Pb concentration levels; this can be explained by the dilution effect associated with the increase of Pb-depleted coarse particles.s.s.

• 열처리공학회지
• /
• 제26권6호
• /
• pp.306-316
• /
• 2013

Microstructure and fracture behavior of a multi-phase low-density steel were investigated. After hot-rolling and heat treatment, the microstructure of low-density steel was composed of coarse ferrite grains and elongated bands which include second phases such as austenite, martensite and ${\kappa}$-carbide depending on holding time during isothermal heat treatment. After tensile test, microcracks were observed at martensite or ${\kappa}$-carbide interface in the elongated bands. Coarse ferrite grains showed cleavage fracture behavior regardless of second phase. The cleavage fracture of ferrite could be attributed to their coarse grain size and solute atoms that increase ductile-to-brittle transition temperature of ferrite. Despite of the tendency of cleavage fracture in coarse ferrite grains, a specimen having coarse spheroidized ${\kappa}$-carbide particles in the elongated bands showed high total elongation of 30%. Thus, the easiness of plastic deformation in the elongated band seems to play an important role in retardation of cleavage crack formation in coarse ferrite grains.

• 한국대기환경학회지
• /
• 제12권5호
• /
• pp.523-528
• /
• 1996

Aerosol Particles were collected in a heaby traffic region in pusan. Samples were collected in two size fractions with a two-stage sampler during the day and the night. Elemental concentrations of these aerosol particles were determined by a PIXE(Proton Induced X-ray Emission) analysis method. The results suggest that the elements originating mainly from natural sources such as Si, Ca, Fe, Cl, and K are dominent in the coarse fraction, but the elements such as S, Pb, Br, and Zn are dominent in the fine fraction. Br/Pb ratio are evaluated in both coarse and fine size fraction, and which are mainly emitted automobile sources. The study further also discussed other Br/Pb ratio related works described elsewhere. Sulfur in the fine fraction was continuously increased during the sampling period without time variation.

• 한국농공학회지
• /
• 제43권2호
• /
• pp.132-139
• /
• 2001

This study deals with coal-mine waste (CMW) for use in concrete as a replacement of normal aggregates. The CMW was collected from Sabuk region. Ganwon-do. Fine and coarse aggregates from CMW were prepared by using a crusher and separating debris with #4 sieve. CMW aggregates showed good physical and mechanical properties with having specific gravity over 2.65, absorption less than 1%, and abrasion ratio below 20%. However, particle shape of CMW was poor because of non-isotropic nature of matrix which cause particles to be long or flat. Since irregular particles caused a poor workability, to make workability better, a 1/4 of coarse aggregate was replaced with normal aggregate together with a superplasticizer. Compressive strength and other mechanical properties of CMW concrete were very good. Color of the concrete was darker than normal concrete due to black color of CMW. In conclusion, characteristics of CMW concrete was acceptable for use as a structural concrete material.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.721-724
• /
• 2006

In this study, particle size distribution of cement powder system were adjusted using the blast furnace slag powder, Blaine $2250cm^2/g\;and\;8300cm^2/g$, which easy to adjust particle size distribution to examine how particle size distribution of the binder has an effect on rheological properties of the cement paste. In addition, the relationship between n-value of Rosin-Rammler function and plastic viscosity were discussed. All measured flow curves represented thixotropy behavior and the hysteresis area was smaller for the more added coarse particle. When the combination was based on a ratio of $20{\sim}25vol%$ fine particles, $30{\sim}40vol%$ OPC and $40{\sim}45vol%$ coarse particles of the total volume, a high fluidity and low yield strength was achieved.

• The Korean Journal of Ceramics
• /
• 제5권2호
• /
• pp.137-141
• /
• 1999

To increase the strength of high-purity porous mullite ceramics, ultra fine mullite precursor powders of about 10nm in diameter were deposited at point of contact between primary coarse mullite particles of about 60$\mu\textrm{m}$. The deposited and hetero coagulated structures of ultra fine mullite precursor powders were controlled by pH. The optimum pH condition to form a uniform deposition of mullite powders between coarse mullite particles was in the range from 7 to 8. Deposition of the ultra fine powders did not form at pH < 7 and pH > 10 irregular deposition was observed from pH 8 to 9.

• 한국대기환경학회지
• /
• 제29권5호
• /
• pp.656-667
• /
• 2013

The non-exhaust coarse, fine, and ultrafine particles were characterized by on-road driving measurements using a mobile sampling system. The on-road driving measurements under constant speed driving revealed that mass concentrations of roadway particles (RWPs) were distributed mainly in a size range of 2~3 ${\mu}m$ and slightly increased with increasing vehicle speed. Under braking conditions, the mode diameters of the particles were generally similar with those obtained under constant speed conditions. However, the PM concentrations emitted during braking condition were significantly higher than those produced under normal driving conditions. Higher number concentrations of ultrafine particles smaller than 70 nm were observed during braking conditions, and the number concentration of particles sampled 90 mm above the pavement was 6 times higher than that obtained 40 mm above the pavement. Under cornering conditions, the number concentrations of RWPs sampled 40 mm above the pavement surface were higher than those sampled 90 mm above the pavement. This might be explained that a nucleation burst of a lot of vapor evaporated from the interaction between the tire and the road pavement under braking conditions continuously occurred by cooling during the transport to the sampling height 90 mm, while, for the case of cornering situations, the ultrafine particle formation was completed before the transport to the sampling height of 40 mm.

• Asian Journal of Atmospheric Environment
• /
• 제4권3호
• /
• pp.141-149
• /
• 2010

Aerosol size and number concentration were observed in the atmospheric boundary layer over Beijing (from near the ground to 1,200 m) on March 15 (a clear day) and 16 (a dusty day), 2005. The results were further compared with lidar measurements in order to understand the dependency of extinction on the particle size distribution and their vertical changes. The boundary layer atmosphere was composed of several sub-layers, and a dry air layer appeared between 400 and 1,000 m under the influence of dust event. In this dry air layer, the concentration of the fine-mode particles (diameter smaller than $1.0\;{\mu}m$) was slightly lower than the value on the clear day, while the concentration of coarse-mode particles (diameter larger than $1.0\;{\mu}m$) was remarkably higher than that on the clear day. This situation was attributed to the inflow of an air mass containing large amounts of Asian dust particles and a smaller amount of fine-mode particles. The results strongly suggest that the fine-mode particles affect light extinction even in the dusty atmosphere. However, quantitatively the relation between extinction and particle concentration is not satisfied under the dusty atmospheric conditions since laser beam attenuates in the atmosphere with high concentration of particles. Laser beam attenuation effect becomes larger in the relation between extinction and coarse particle content comparing the relation between extinction and fine particle content. To clarify this problem technically, future in situ measurements such as balloon-borne lidar are suggested. Here extinction was measured at 532 nm wavelength. Measurements of extinction at other wavelengths are desired in the future.

• 한국세라믹학회지
• /
• 제44권1호
• /
• pp.6-11
• /
• 2007

The rheological properties of slag cement pastes by effect of particle size distribution of binder were investigated using a Rheostress 1 rheometer (Haake) with a cylindrical spindle and the relationship between fluidity particle size distribution using the Rosin-Rammler equation. Samples are combined the two types of slag powder and OPC, fine slag particles sized Elaine specific surface area $8,000cm^2/g$, coarse slag particles sized Elaine specific surface area $2,000cm^2/g$, intermediate OPC particles $3,450cm^2/g$, used to search for the combination that would yield the best quality product. The all flow curves which were measured by rheometer showed hysterisis and could be classified into 4 types. When the combination was based on a ratio of 15-20 vol% fine particles, 40-50 vol% intermediate particles, 30-40 vol% coarse particles of the total volume, a high fluidity and low yield-strength was achieved. The Rosin-Rammler function can explain aboved correlation flow curve types. On type 1, the n-value had a correlation with plastic viscosity however the blend of type 2 and 3 showed consistent n-value regardless of plastic viscosity. In addition, the blend in type 4 tended to a rise in fluidity according to the increase of the n-value.