• Restorative Dentistry and Endodontics
• /
• v.25 no.3
• /
• pp.474-482
• /
• 2000

Currently frequency-dependent type electronic apex locators have been widely used to determine the working length in endodontic treatment. But, accuracy of electronic apex locators is controversial. The purpose of this study was to evaluate the accuracy of Root-ZX(Morita Co., Japan) at different kinds of conditions of root canals compared with the radiographic working length. The 40 extracted human anterior teeth with fully formed apices and without any caries were used. The radiographs were taken for working length with the 0.5mm short of #15 K-file tip just visible at the foramen under the surgical microscope(Carl Zeiss Co. Germany) at 25X. Then the electronic working lengths were determined with Root-ZX at the different kinds of conditions of root canals according to the presence of electrolyte and Crown-down pressureless technique. The results were as follows ; 1. There was no significant statistical difference in working length between radiograph and Root-ZX. 2. There was no significant statistical difference in electronic working length between the canal with electrolyte and without electrolyte. 3. There was no significant statistical difference in electronic working length between the canal without any instrumentation and after Crown-dow pressureless technique. 4. Of the total 40 root canals, 85% in Group I, 92.5% in Group II, 95% in Group III and 95% in Group IV using Root-ZX showed coincidence within 0.5mm accuracy compaing with the radiographic working length. The results showed that the Root-ZX can be use effectively for measuring the working length of root canal after instrumentation with Crown-down pressureless technique regardless of the presence of electrolyte in root canal.

• Nuclear Engineering and Technology
• /
• v.55 no.8
• /
• pp.2812-2822
• /
• 2023

The supercritical carbon dioxide (sCO₂) Brayton power cycle is more effective than the conventional power cycle and is more widely applicable to heat sources. The inlet working conditions of the compressor have a higher influence on their operating performance because the thermophysical properties of the CO₂ vary dramatically close to the critical point. The flow in the sCO₂ compressor is simulated and the compressor performance is analyzed. The results show that the sCO₂ centrifugal compressor operates outside of its intended parameters due to the change in inlet temperature. The sCO₂ compressor requires more power as the inlet temperature increases. The compressor power is 582 kW when the inlet temperature is at 304 K. But the power is doubled when the inlet temperature increases to 314 K, and the change in the isentropic efficiency is within 5%. The increase in the inlet temperature significantly reduces the risk of condensation in centrifugal compressors. When the heat load of the sCO₂ power system changes, the inlet pressure to the turbine can be kept constant by regulating the rotational speed of compressors. With the increase in rotational speed, the incidence loss and condensation risk increase.

• Annals of Occupational and Environmental Medicine
• /
• v.35
• /
• pp.18.1-18.7
• /
• 2023

South Korea has the highest policy priority for working hour regulations because it has longer annual working hours than other Organization for Economic Development Co-operation and Development countries and has fewer holidays. According to the results of the Working Conditions Surveys between 2006 and 2020, in 2020, 6% of wage earners worked for > 52 hours weekly. The percentage of workers exceeding 52 hours weekly has decreased over time; however, disparities exist based on age, industry, occupation, company type, and company size, particularly in service-, arts-, and culture-related occupations and workplaces with fewer than 5 employees. South Korea's working hours system is greatly influenced by the 52-hour weekly maximum; sometimes, a maximum of 64-69 hours, including overtime, is theoretically possible. To ensure healthy working hours, it is important to actively protect workers who fall through the cracks, such as those in businesses with fewer than 5 employees.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.36 no.2
• /
• pp.63-73
• /
• 2013

Nowadays, the human resources of an organization are very important in order to survive in competitive business environment. This study investigates the influence of four decision-making styles in Myer-Briggs Type Indicator (MBTI) and working conditions on organizational effectiveness. Job satisfaction and immersion have been regarded as key conceptions of organizational effectiveness. The result of this study has shown that organizational effectiveness are influenced by personality types and working conditions. Based on the result, an enterprise must provide working conditions which are conducive and suitable for all decision-making styles. For ST-type, the composition of good relationship with superiors, clear organization's visions and goals and rewarding compensation on original idea contribution need to be provided. On the other hand, autonomic authority and job assistance in co-worker are more suitable for NT-type. Finally, in the case of SF-type, the organization must give job assistance in co-worker.

• Safety and Health at Work
• /
• v.14 no.4
• /
• pp.488-491
• /
• 2023

This study aims to ascertain occupations potentially at greatest risk of exposure to SARS-CoV-2 based on pre-lockdown working conditions in France. We combined two French population-based surveys documenting workplace exposures to infectious agents, face-to-face contact with the public, and working with colleagues just before the pandemic. Then, for each 87-level standard French occupational grouping, we estimated the number and percentage of the French working population reporting these occupational exposure factors, by gender, using survey weights. As much as 40% (11 million) of all workers reported at least two exposure factors. Most of the workers concerned were in the healthcare sector. However, army/police officers, firefighters, hairdressers, teachers, cultural/sports professionals, and some manual workers were also exposed. Women were overrepresented in certain occupations with potentially higher risks of exposure such as home caregivers, childminders, and hairdressers. Our gender-stratified matrix can be used to assign prelockdown work-related exposures to cohorts implemented during the pandemic.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.335-338
• /
• 1997

Platinum-Cobalt alloy thin films were deposited on A1$_2$O$_3$substrate by magnetron cosputtering for RTD temperature sensors with wide temperature ranges. We made Pt-Co alloy resistance patterns on the A1$_2$O$_3$substrate by lift-off method and fabricated Pt-Co alley RTD temperature sensors by using Pt-wire, Pt-paste. We investigated the physical and electrical characteristics of theme films under various conditions, input power, working vacuum, annealing temperature and time, and also after annealing these films. The resistivity and sheet resistivity of these films were decreased with increasing the annealing temperature. At input power of Pt : 4.4 W/cm$^2$, Co : 6.91 W/cm$^2$, working vacuum of 10 mTorr and annealing conditions of 800$^{\circ}C$ and 60 min, the resistivity and sheet resistivity of Pt-Co thin films was 15${\mu}$$\Omega$$.$cm and 0.5$\Omega$/ , respectively, and the TCR value of Pt-Co alloy thin films with thickness of 3000${\AA}$ was 3740ppm/$^{\circ}C$ in the temperature range of 25∼600$^{\circ}C$. These results indicate that Pt-Co alloy thin films hove potentiality for the RTD with wide temperature ranges.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.11
• /
• pp.1201-1206
• /
• 2014

This paper presents the development of an event-based operator model of a wheel loader for virtual V-pattern working. The objective of this study is to analyze the performance and dynamic behavior of the wheel loader for a typical V-pattern. The proposed typical V-pattern working is divided into four stages. The developed operator model is based on eight events, and the operator's inputs are occurred sequentially by event. A 3D dynamic simulation model of the wheel loader is developed and used to analyze the dynamic behavior during working, and the simulation results are compared with the experimental data of V-pattern working. The proposed 3D dynamic simulation model and operator model are constructed using MATLAB/Simulink. The proposed operator model for V-pattern working is expected to enable evaluation of the working performance and dynamic behavior of the wheel loader.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.2
• /
• pp.41-46
• /
• 2011

This study investigated the changes in performance and operating characteristics of an F-class gas turbine according to the change of working fluid from air to carbon dioxide. The revised gas turbine is the topping cycle of the semi-closed oxy-fuel combustion combined cycle. With the same turbine inlet temperature, the $CO_2$ gas turbine is expected to produce about 85% more power. The main contributor is the greater compressor mass flow and the added oxygen flow for the combustion. Compressor pressure ratio increases about 50%. However, the gas turbine efficiency reduces about 10 %. Modulation of inlet guide vane to reduce the compressor inlet mass flow, the major purpose of which is to reduce the compressor inlet Mach number, was also performed.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2008.09a
• /
• pp.112-117
• /
• 2008

The Insulation, which is consist of the glass wool, mineral wool or perforated SUS plate, installed on the wall or under ceiling for the protecting heat and the blocking the noise of engine room area. In our shipyard, designing the structure model of insulation is hard and difficult, Because designed the insulation model is considered of any factors which are hull model properties of panel shape, direction and thickness and service of area. In this paper, We issue the way to utilize shape and direction of the hull model information and specific character of working space in engine room.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.27 no.3
• /
• pp.187-192
• /
• 2017

Objectives: It is difficult to identify exposure factors in the semiconductor industry due to low exposure levels to hazardous substances and because various processes take place in fabrication (FAB). Furthermore, a single worker often experiences a variety of job histories, so it is difficult to classify similar exposure groups (SEG) in the semiconductor industry. Therefore, we intend to develop a new exposure index, the period of working in FAB, that is applicable to the semiconductor industry. Methods: First, in specifying the classification of jobs, we clearly distinguished whether they were FAB workers or non-FAB workers. We checked FAB working hours per week through questionnaires administered to FAB workers. We derived an exposure index called FAB-Year that can represent the period of working in FAB. FAB-Year is an index that can quantitatively indicate the period of working in FAB, and one FAB-Year is defined as working in FAB for 40 hours per week for one year. Results: A total of 8,453 persons were surveyed, and male engineers and female operators occupied 90% of the total. The average total years of service of the subjects was 9.7 years, and the average FAB-Year value was 6.8. This means that the FAB-working ratio occupies 70% of total years of service. The average FAB-Year value for female operators was 8.4, for male facility engineers it was 7.7, and for male process engineers it was 3.5. A FAB-Year standardization value according to personal information (gender, job group, entry year, retirement year) for the survey subjects can be calculated, and standardized estimation values can be applied to workers who are not participating in the survey, such as retirees and workers on a leave of absence (LOA). Conclusions: This study suggests an alternative method for overcoming the limitations on epidemiological study of the semiconductor industry where it is difficult to classify exposure groups by developing a new exposure index called FAB-Year. Since FAB-Year is a quantitative index, we expect that various approaches will be possible in future epidemiological studies.