• 설비공학논문집
• /
• 제11권6호
• /
• pp.716-724
• /
• 1999

In co-orbiting scroll compressor, the two scroll members are to orbit with independent radii, producing a relative orbit motion between them. One scroll member is driven by the crank mechanism while the motion of the other member is determined by geometrical constraints and reacting forces. This paper presents an analytical study on the performance of a co-orbiting scroll compressor. The following results have been obtained: Radial contact force between the scroll wraps is virtually free from the centrifugal force of the orbiting scroll member. The frictional losses are somewhat increased due to the complicated drive mechanism, yielding to a little lower EER compared to conventional radially compliant scroll compressors .

• 설비공학논문집
• /
• 제17권4호
• /
• pp.325-332
• /
• 2005

This paper addresses the development of a scroll expander for power generation from relatively low temperature steam source. It has a double-sided orbiting scroll member so that no thrust bearing is needed to support the base plate of the orbiting scroll. Three power transmission shafts are placed at the periphery of the orbiting scroll base plate, and these shafts can also function as anti-rotation devices. Final output is obtained from the main central shaft engaged with the three power transmission shafts through gear assembly. The clearance between the fixed and orbiting scroll elements was estimated by comparing measurement of the mass flow rate with calculation results of a computer simulation. Due to large clearance, the expander total and volumetric efficiencies were measured to be $34\%\;and\;43\%$, respectively. It has been shown through the computer simulation that the total and volumetric efficiencies could be improved to $65\%\;and\;83\%$, respectively, if the current clearance is reduced by half.

• 대한원격탐사학회지
• /
• 제39권2호
• /
• pp.169-181
• /
• 2023

최근 지구온난화의 주원인인 이산화탄소(carbon dioxide, CO₂)의 배출량을 줄이기 위하여 한국은 탄소 배출량 감축목표와 탄소 중립을 선언하였으며, 이에 따른 지역별 배출량과 대기 중 CO₂ 농도의 정확한 평가가 중요해지고 있다. 본 연구에서는 Orbiting Carbon Observatory-2 위성자료와 CO₂ 배출량 자료를 활용하여 위성기반 대기 중 CO₂ 농도와 배출량의 시공간적 차이를 확인하고, 이러한 차이를 식생 성장에 따른 광합성 반응지수인 태양유도 엽록소 형광(solar-induced fluorescence, SIF)을 이용하여 설명하고자 하였다. 2014년부터 2018년까지 한국 지역에서 환경부 온실가스종합정보센터(Greenhouse Gas Inventory and Research Center, GIR) 및 Emissions Database for Global Atmospheric Research (EDGAR) 배출량은 지속적으로 증가하였지만, 위성에서 관측된 CO₂ 농도는 2018년에 전년 대비 감소하는 것으로 나타났다. 지역적으로 살펴보면 경기도, 충청북도는 2018년에 GIR, EDGAR 배출량이 증가하였지만 CO₂ 농도는 감소하였다. 또한, 배출량과 위성관측 CO₂ 농도의 상관성분석에서 서울과 강원도 지역에서 각각 0.22 (GIR), 0.16 (EDGAR)으로 낮은 상관성을 보였다. 대기 중 CO₂ 농도는 SIF와 지역별로 상이한 상관관계를 보였는데, 5~9월의 CO₂-SIF 상관성분석에서 서울과 경기지역은 -0.26의 음의 상관계수를, 충청북도와 강원도는 0.46의 양의 상관계수를 보이며 CO₂ 흡수와 대기 중 농도의 관계성이 지역별로 차이가 있음을 밝혔다. 따라서 대기 중 CO₂ 농도와 배출량 사이의 관계성을 분석함에 있어 CO₂ 흡수 과정에 대한 고려가 필요하다는 것을 시사한다.

• Tribology and Lubricants
• /
• 제19권3호
• /
• pp.146-150
• /
• 2003

The natural refrigerant $CO_2$has attracted as an alternative refrigerant currently used in air conditioning system, which has high global warming potential. In this study, the tribological characteristics of the sliding surfaces between a fixed scroll and an orbiting scroll of the scroll compressor were investigated in $CO_2$/ POE mixed environment. The pin-on-disk type sliding tests were carried out under the various sliding speeds, normal loads. surface roughness, and pressures. During the test, friction forces, wear amount and surface temperature were monitored.

• 설비공학논문집
• /
• 제16권3호
• /
• pp.241-249
• /
• 2004

A parametric study on the scroll wrap configuration factors of a $CO_2$scroll compressor for heat pump water heater has been carried out. Since there are 7 scroll wrap design parameters and 5 equations relating them, two of the design parameters can be selected as independent parameters. In this study, the wrap thickness and orbiting radius are chosen as independent ones. Computer simulation program has been used to estimate the compressor performance at various combinations of the scroll wrap design parameters. It has been found that there exists optimum combination of the wrap parameters for the highest compressor performance over analyzed ranges of the design parameters.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2007년도 동계학술발표대회 논문집
• /
• pp.397-403
• /
• 2007

In this paper, conceptual design of scroll expander-compressor for Stirling engine utilizing solar energy as heat source has been carried out. Orbiting scroll member was designed to have a double-sided structure to reduce the overall scroll size and to cancel out the axial forces on the orbiting scroll base plate. Diameter of designed scroll base plate was about 251 mm for the expander, and it was about 218 mm for the compressor. With operating condition such as temperature range of $400^{\circ}C/20^{\circ}C$, pressure range of 6 MPa/2 MPa, and shaft speed of 2700 rpm, the shaft output of the designed scroll expander was calculated to be 49.8 kW, while input power for the scroll compressor was 38.6 kW, yielding 11.2 kW for the output power of the Stirling engine. Overall efficiencies of the scroll expander and compressor were 93.73% and 92.87%, respectively.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제17권4호
• /
• pp.115-122
• /
• 2009

Numerical simulations for scroll, two-stage twin rotary, and two-cylinder reciprocating compressors have been carried out to understand the effectiveness of each type compressor for heat pump water heater application using $CO_2$ as refrigerant. For suction pressure of 3.5 MPa and discharge pressure of 9 MPa, clearance volume ratio of the reciprocating compressor needs to be about 5% or less to have the volumetric efficiency comparable to that of the scroll compressor with tip clearance of $5\;{\mu}m$. Volumetric efficiency of the scroll compressor is quite sensitive to tip clearance. Adiabatic efficiency of the twin rotary compressor was calculated to be the lowest among the three types, and the most severe drawback of the $CO_2$ scroll compressor was a significant increase in the mechanical loss at the thrust surface supporting the orbiting scroll member. While the scroll compressor showed very smooth torque load variation, peak-to-peak torque variations of the twin rotary and two-cylinder reciprocating compressors were about 50% and 250%, respectively.

• 대한기계학회논문집A
• /
• 제24권5호
• /
• pp.1305-1313
• /
• 2000

In a co-rotating scroll compressor, both scrolls rotate on their fixed axes contrary to the conventional orbiting type scroll machine. This implies fixed locations and directions of the gas pressure force and sealing force. Because the tilting moment is mainly caused by interplay between the resultant force of above forces and bearing reaction force, the variation during one cycle is relatively small. Under real operation, this moment is balanced by the restoring moment created by the reaction between the baseplate and thrust bearing or between the scroll tip and baseplate. If these reactions become too large, greater torque is required due to increased friction in addition to the wear of mating parts. Consequently, appropriate study and minimization of tilting moment is important in the design of scroll machines. In this study, taking into account of the small variation of tilting moment during one cycle, we minimize the moment and thrust bearing reaction force by a properly designed back pressure chamber. As a result, for both the driving and driven scrolls, the tilting moment and the reaction force of thrust bearing can be minimized. And the stability is improved for all cases.

• 대한치과보철학회지
• /
• 제29권2호
• /
• pp.295-317
• /
• 1991

The discrepancy between centric relation and centric occlusion have a great role on the successful prosthodontic and occlusal treatment. This study was performed to investigate the effect of the discrepancy between centric relation and centric occlusion on condylar guidance inclination and Bennett shift (immediate and progressive side shift). Sixteen adults who have physiologically normal occlusion and are free of TMJ dysfunction were selected. The amount of the sagittal CR-CO discrepancy in lower anterior incisor was obtained by Saphon Visi-Trainer. The amount of the CR-CO discrepancy in condylar level was measured on the individualized corrected tomography. Pantronic survey was performed by using a arbitrary hinge axis according to manufacturer's direction. All subjects were divided into two groups, group I (small) and group II (large), according to the amount of CR-CO discrepancy. At first the amount of the CR-CO discrepancy in condylar level between two groups was compared and then the condylar guidance inclination and Bennett shift between two groups were compared and analyzed. The results were as follows; 1. The average CR-CO discrepancy in lower anterior incisors was 0.7mm superoinferiorly, 0.49mm anteroposteriorly, and 0.88 mm in total. The average CR-CO discrepancy in condylar level was 0.43mm. 2. The CR-CO discrepancy measured on teeth level and condylar level were highly correlated (p<0.01). 3. The correlation of the condylar position in the glenoid fossa between two groups was not statistically significant. 4. The large CR-CO discrepancy group showed greater amount of Bennett shift and condylar guidance inclination, but there is no statistical significancy. 5. It seems that the CR-CO discrepancy have greater effect on progressive side shift than other elements of mandibular movements.

• 대한원격탐사학회지
• /
• 제39권2호
• /
• pp.129-142
• /
• 2023

본 연구는 2018년 4월부터 2022년 4월까지 Orbiting Carbon Observatory-2/3의 건조공기 이산화탄소 몰분율(column-averaged carbon dioxide dry-air mole fraction, XCO₂) 자료와 TROPOspheric monitoring instrument의 일산화탄소(carbon monoxide, CO) 및 이산화질소(nitrogen dioxide, NO₂) 연직컬럼농도(본 연구에서 XCO, XNO₂로 명명) 자료를 활용하여 한국과 중국의 도시 및 권역에 대해 CO와 CO₂, CO와 NO₂의 비율을 분석하고, 사회경제적 지표(인구, 차량 등록 대수, 지역내총생산)와 비율의 관계, 한국과 중국에서의 특성 차이를 제시하였다. 먼저 CO₂, CO 그리고 NO₂ 세 기체상 물질의 대기 중 체류시간 차이로 CO₂, CO는 배경값과 추세선을 제거한 ΔXCO₂, ΔXCO로 분석하였다. 지역별로 세 값을 비교한 결과 ΔXCO, ΔXCO₂는 중국 지역이 XNO₂는 한국 지역이 상대적으로 높은 값을 보였으며, 두 값의 비율(ΔXCO/ΔXCO₂, ΔXCO/XNO₂) 모두 한국보다 중국에서 높은 것으로 나타났다. ΔXCO/ΔXCO₂, ΔXCO/XNO₂와 사회경제적 지표는 양의 상관관계를 보였으며, 이는 도시 규모가 크고 경제활동이 활발할수록 대기오염기체 및 온실기체의 농도가 높다는 점을 시사한다. 한국과 중국의 비율 특성 차이를 분석하기 위해 두 나라의 지역별로 분석한 ΔXCO와 ΔXCO₂ 관계는 한국은 음의 관계성을 중국은 양의 관계성을 나타냈다. ΔXCO와 XNO₂의 상관성을 여름과 겨울에 대해 각각 살펴본 결과, 한국은 계절에 따른 ΔXCO 증감이 크지 않은 것에 비해 중국은 북동부 지역을 중심으로 계절에 따른 ΔXCO와 XNO₂의 증감이 크게 나타나며 관계성의 차이를 보였다. 이는 온실기체와 대기오염기체의 비율을 분석할 때, 계절 변동성 및 국가별 배출 특성을 감안해야 함을 시사한다.