• 소성∙가공
• /
• 제18권1호
• /
• pp.80-86
• /
• 2009

This paper presents the plastic inhomogeneous deformation behavior of bimetal composite rods during the axisymmetric and steady-state extrusion process through a conical die. The rigid-plastic FE model considering frictional contact problem was used to analyze the co-extrusion process with material combinations of Cu/Al. Different cases of initial geometry shape for composite material were simulated under different conditions of co-extrusion process, which includes the interference and frictional conditions. From the simulation results, the sleeve cladding rate at the core/sleeve interface was recorded as a distribution of diameter ratio and interference conditions, which will be useful for the investigations of the bonding process during co-extrusion process. In addition, the results of the co-extrusion, connected with the results of the variations of diameter rate and average contact pressure, demonstrate a good agreement and present the possibility of describing the parameters of the plastic zones in non-uniform deformation of these type of composite materials.

• Design & Manufacturing
• /
• 제7권1호
• /
• pp.11-18
• /
• 2013

This paper presents the plastic inhomogeneous deformation behavior of bimetal composite rods during the axisymmetric and steady-state extrusion process through a conical die. The rigid-plastic FE model considering frictional contact problem was used to analyze the co-extrusion process with material combinations of Cu/Al. Different cases of initial geometry shape for composite material were simulated under different conditions of co-extrusion process, which includes the interference and frictional conditions. The main design parameters influencing on deformation pattern are diameter ratio of the composite components and semi-die angle. Efforts are focused on the deformation patterns, velocity gradient, predicted forming load and the end distance through the various simulations. Simulation results indicate that there is an obvious difference of forming pattern with various diameter ratio and semi-die angle. The analysis in this paper is concentrated on the evaluation of the design parameters on the deformation pattern of composite rod.

• 한국정밀공학회지
• /
• 제26권2호
• /
• pp.71-77
• /
• 2009

In the automotive industry, aluminum is widely used to reduce the vehicle weight. Aluminum curved extruded components are used for the design of frame parts. This study investigates the curvature extrusion process to produce the aluminum curved suspension arm. In the curvature extrusion process, the bending process is simultaneously carried out with the extrusion process. Firstly, porthole extrusion was investigated by using FE analysis to produce aluminum suspension arm. And then the bending process condition was determined to produce the final suspension arm with the required curvature. In this research, the guide roll movement causes the bending of extruded product. The moving distance and velocity of guide roll were controlled to meet the required curvature of suspension arm. Finally, the curved suspension arm was manufactured by the curvature extrusion experiment under the proposed curvature extrusion condition.

• Design & Manufacturing
• /
• 제10권1호
• /
• pp.12-18
• /
• 2016

Although magnesium alloy has received much attention to date for its lightweight and high specific strength, their applications are impeded by the low formability which is caused by the hexagonal crystal structure at room temperature. In general, equal-channel angular extrusion(ECAE) is recognized as one of the attractive severe plastic deformation techniques where the processed bulk metals generally achieve ultrafine-grained microstructure leading to improved physical characteristics and mechanical properties. ECAE process has several parameters such as angle of die, process temperature, process route and speed. During ECAE process of Mg alloy, these parameters has great influence on the extrudability and the mechanical properties of alloy. The aim of this study is to estimate the influences of process conditions on the formability of AZ31 and AZ31-CaO alloys. Mg alloys are processed through ECAE at elevated temperatures using three types of die with channel angle of $90^{\circ}$, $110^{\circ}$, $135^{\circ}$ using route $B_c$, respectively. This study discusses the feasibility of using ECAE to improve both formability and strength on magnesium alloys by comparative analyzing the mechanical properties and microstructural evolution in each condition.

• 소성∙가공
• /
• 제16권7호
• /
• pp.530-537
• /
• 2007

This paper is concerned with the analysis of plastic deformation of bimetal co-extrusion process. Two sets of material combination have been adopted for analysis, i.e. combinations of Cu/Al and Fe/Al. In the first set of material combination, the selected materials are AA 1100 aluminum alloy as hard material and CDA 110 as soft one. This type of material selection is to examine the effect of hard core and soft sleeve and vice versa on the deformation pattern in terms of plastic zone and velocity discontinuity along the contact surface between construction materials. Four different cases of co-extrusion process in terms of material combination and interference bonding were simulated to investigate the effect of material arrangement between core and sleeve, and of bonding on the plastic zones and velocity discontinuity. In the other set of material combination, model materials used as core and sleeve were AA 1100 and AISI 1010, which are relatively soft and hard, respectively. Process parameters except diameter ratio of core to sleeve material such as semi-die angle, reduction in area in global sense and die comer radius have been set constant throughout the simulation to concentrate our effort on the analysis of influence of diameter ratio on deformation behavior such as deformation zone, surface expansion, exit velocity discontinuity between composite materials, and extrusion forces.

• 한국산업보건학회지
• /
• 제3권1호
• /
• pp.91-98
• /
• 1993

This study was carried out to investigate characteristic of vinyl chloride emissioned from poly vinyl chloride extrusion process and to evaluate the efficiency of local exhaust ventilation system. Before local ventilation facility was constructed in poly vinyl chloride extrusion process, the average worker exposure to vinyl chloride was 3.15 ppm, which exceeded Threshold Limit Value of American Conference of Gorvernmental Industrial Hygienists (ACGIH-TLV), 1 ppm. lt is possible that vinyl chloride residues in the poly vinyl chloride resin was released or degased due to extrusion heat. The larger the width of vinyl tube become, the higher worker exposure to vinyl chloride was. It is estimated that vinyl chloride from vinyl chloride resin increased as amount of poly vinyl chloride resin extruded in the extrusion process increased. Canopy hood was an appropriate type for poly vinyl chloride resin extrusion process. This local exhaust ventilation has fan static pressure of 7.65 inch wg($190mmH_2O$, total volumetric flowlate of 4,796 CFM ($135.8m^3$/min) and fan power requirement of 12 hp (8.952 Kw). After this local exhaust ventilation was constructed there, the average concentration of worker exposure to vinyl chloride was reduced to be 0.46 ppm, which was below the Threshold Limit Value, 1 ppm. Also, the removal efficiency rate of vinyl chloride attained by local exhaust ventilation was 85.3%. It was a statistically significant (p<0.01).

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 제7회 단조 심포지엄
• /
• pp.85-91
• /
• 2002

Of all the many types of machine elements which exist today, gears are among the most commonly used. Many researches have been done to manufacture helical gears by cold forging and extrusion. Although cold forging and extrusion were applied to some bevel, spur, and helical gears, problems in connection with reducing forming load and tool life still make it difficult for the related methods to be commercialized. In this study, focusing on reducing load in forming helical gears, extrusion of helical gears by a two-step process is proposed. The process is composed of an extrusion step of spur gears used as preform and a torsion step of the preform to make helical gears. Upper-bound analysis for the two-step process is performed and compared with results of experiments. The newly proposed method can be used as an advanced forming technique to remarkably reduce the forming load and replace the conventional forming process of helical gears.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.824-828
• /
• 2002

Of all the many types of machine elements which exist today, gears are among the most commonly used. Many researches have been done to manufacture helical gears by cold forging and extrusion. Although cold forging and extrusion were applied to some bevel, spur, and helical gears, problems in connection with reducing forming load and tool life still make it difficult for the related methods to be commercialized. In this study, focusing on reducing load in forming helical gears, extrusion of helical gears by a two-step process is proposed. The process is composed of an extrusion step of spur gears used as preform and a torsion step of the preform to make helical gears. Upper-bound analysis for the two-step process is performed and compared with results of experiments. The newly proposed method can be used as an advanced forming technique to remarkably reduce the forming load and replace the conventional forming process of helical gears.

• 한국주조공학회지
• /
• 제13권3호
• /
• pp.248-258
• /
• 1993

A semi-solid alloy in which solid and liquid phase are co-existing is obtained by stirring of A17075 molten metal. A semi-solid alloy is dependent on the corresponding temperature within the solid-liquid range, and the process parameters should be controlled accurately to obtain the homogeneous semisolid alloy. The fabrication possibility of fiber-reinforced aluminum alloy containing $Al_2O_3$ short fibers with vigorous agitation of short fibers were obtained by control of stirring time, solid fraction and impeller speed in extrusion billet fabrication processes. The microstructure to extrusion billet fabricated by low pressure casting was investigated for fiber dispersion state. The relationship between the extrustion force and velocity at hot extrustion, the flow strain and extrusion ratio were theoretically described. The surface defects with lubricants and without lubricant after hot extrusion were investigated. The composites materials after hot extrusion were measured by vickers hardness with extrusion ratio. It has become clear that the secondary working such as hot extrusion was very useful to obtained improved the mechanical properties of metal matrix composites.

• 한국재료학회지
• /
• 제21권1호
• /
• pp.39-45
• /
• 2011

In this study, the heat flow of the plant scale aluminum extrusion process was investigated to establish optimum continuous heat treatment conditions. During the extrusion of 6061 aluminum alloy, processing parameters such as the extrusion pressure, speed and temperature histories of billets were logged as a function of time. The surface temperature of the billets increased at constant ram speed, while it decreased with decreases of the ram speed. In order to maintain the billet temperature within a solutionizing temperature range prior to the succeeding water quenching step, the ram speed or the temperature of the blower should be controlled. The temperature histories of the billets during the extrusion and hot air blowing processes were successfully simulated by using the velocity boundary model in ANSYS CFX. The methodology to design an optimum process by using a commercial simulation program is described in this study on the basis of the metallurgical validation results of the microstructural observation of the extrudates. The developed model allowed the advantages of taking into account the motion of the extrudate coupled with the temperature change based on empirical data. Calculations were made for the extrudate passing through the isothermal chamber maintained at appropriate temperature. It was confirmed that the continuous heat treatment system is beneficial to the productivity enhancement of the commercial aluminum extrusion industry.