• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2019.05a
• /
• pp.393-394
• /
• 2019

• Journal of the Korea Organic Resources Recycling Association
• /
• v.22 no.2
• /
• pp.44-49
• /
• 2014

In order to remove the heavy metals from synthetic wastewater containing Pb, Cr, and Cd, the experiment was conducted with a variety of concentration and pH by using the washed and dried coffee grounds as adsorbent. Almost of the heavy metals were removed in thirty minutes and the removal efficiency was maximized to the 80 percents following the different pH conditions. Furthermore, in the case of Cr, the removal efficiency was declined with the increasing of pH. As a result of this study, coffee grounds is proved to be a very good adsorbent to remove the heavy metals.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.419-422
• /
• 2001

The electrical properties of Pr$_{6}$O$_{11}$-based ZnO varistors composed of ZnO-Pr$_{6}$O$_{11}$-CoO-Cr$_2$O$_3$-Dy$_2$O$_3$- based ceramics were investigated with CoO content in the range of 0.5~5.0 mol%. As CoO content is increased, the average grain size and the density were increased in the range of 9.86~27.22 $\mu$m and in the range of 5.25-5.55 g/cm$^3$, respectively. The varistor voltage was decreased in the range of 235.32~86.01 V/mm due to the increase of average grain size with CoO content. The varistors doped with CoO in the rage of 1.0~2.0 mol% exhibited a high nonlinearity, in which is above 55 in the nonlinear exponent and below 1.5 $\mu$A in the leakage current. Increasing CoO content further greatly decreased the nonlinearity.ity.ity.

• Korean Journal of Materials Research
• /
• v.17 no.5
• /
• pp.256-262
• /
• 2007

Effects of interlayer and the combination of different coating methods on the mechanical and corrosion behaviors of TiN and CrN coated on 420 stainless steel have been studied. STS 420 specimen were tempered at $300^{\circ}C$ for 1 hr in vacuum furnace. The TiN and CrN thin film with 2 ${\mu}m$ thickness were coated by arc ion plating and DC magnetron sputtering following the formation of interlayer for pure titanium and chromium with 0.2 ${\mu}m$ thickness. The microstructure and surface analysis of the specimen were conducted by using SEM, XRD and roughness tester. Mechanical properties such as hardness and adhesion also were examined. XRD patterns of TiN thin films showed that preferred TiN (111) orientation was observed. The peaks of CrN (111) and $Cr_2N$ (300) were only observed in CrN thin films deposited by arc ion plating. Both TiN and CrN deposited by arc ion plating had the higher adhesion and hardness compared to those formed by magnetron sputtering. The specimen of TiN and CrN on which interlayer deposited by magnetron sputtering and thin film deposited by arc ion plating had the highest adhesion with 22.2 N and 19.2 N. respectively. TiN and CrN samples shown the most noble corrosion potentials when the interlayers were deposited by using magnetron sputtering and the metal nitrides were deposited by using arc ion plating. The most noble corrosion potentials of TiN and CrN were found to be approximately -170 and -70 mV， respectively.

• The Journal of Advanced Prosthodontics
• /
• v.9 no.1
• /
• pp.22-30
• /
• 2017

PURPOSE. The aim of this study was to investigate the effect of reinforcing materials on the fracture resistances of glass fiber mesh- and Cr-Co metal mesh-reinforced maxillary complete dentures under fatigue loading. MATERIALS AND METHODS. Glass fiber mesh- and Cr-Co mesh-reinforced maxillary complete dentures were fabricated using silicone molds and acrylic resin. A control group was prepared with no reinforcement (n = 15 per group). After fatigue loading was applied using a chewing simulator, fracture resistance was measured by a universal testing machine. The fracture patterns were analyzed and the fractured surfaces were observed by scanning electron microscopy. RESULTS. After cyclic loading, none of the dentures showed cracks or fractures. During fracture resistance testing, all unreinforced dentures experienced complete fracture. The mesh-reinforced dentures primarily showed posterior framework fracture. Deformation of the all-metal framework caused the metal mesh-reinforced denture to exhibit the highest fracture resistance, followed by the glass fiber mesh-reinforced denture (P<.05) and the control group (P<.05). The glass fiber mesh-reinforced denture primarily maintained its original shape with unbroken fibers. River line pattern of the control group, dimples and interdendritic fractures of the metal mesh group, and radial fracture lines of the glass fiber group were observed on the fractured surfaces. CONCLUSION. The glass fiber mesh-reinforced denture exhibits a fracture resistance higher than that of the unreinforced denture, but lower than that of the metal mesh-reinforced denture because of the deformation of the metal mesh. The glass fiber mesh-reinforced denture maintains its shape even after fracture, indicating the possibility of easier repair.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.5
• /
• pp.20-28
• /
• 2014

The high velocity oxygen fuel spraying (HVOF) is a kind of surface modification process technology to form the sprayed coating layer after spraying the powder to molten or semi-molten state by the ultra-high speed at the high-temperature heat source and conflicting with a substrate. It is desirable to melt completely the thermal spray powder in order to produce the coating layer with an optimal adhesion, however, because a semi-molten powder in a spray process has the low efficiency and become a factor that degrades the mechanical property by the inducement of pore-forming within the coating layer. To improve the wear resistance, corrosion resistance and heat resistance, in this study, the plungers of high-speed and ultra-high pressure reciprocating hydraulic pumps for oil and water used in ironwork are produced with $420J_2$ and the coating layers of plungers are formed by the powders of WC-Co-Cr and WC-Cr-Ni including the high hardness WC. The surface of these plungers is modified by the super-mirror face grinding machine using variable air pressure developed in this laboratory, and then the characteristics of cross-sectional microstructure, and surface roughness and hardness values between no operation and 100 days-operation are examined and made a comparison. The fine tops and bottoms on surface roughness curve of oil-hydraulic pump plunger sprayed by WC-Cr-Ni are molded more and higher than those of water-hydraulic pump sprayed by WC-Co-Cr because the plunger diameter of oil-hydraulic pump is 0.4 times smaller than that of water-hydraulic pump and the pressure of oil-hydraulic pump exerted on the plunger is operated with the 70 bars higher than that of water-hydraulic pump. As a result, it is found that the values of centerline average surface roughness and maximum height for oil-hydraulic pump plunger are bigger than those of water-hydraulic pump plunger.

• Corrosion Science and Technology
• /
• v.18 no.6
• /
• pp.285-291
• /
• 2019

In this study, the corrosion characteristics of T22 and T92 steel were investigated in 6O₂ + 16CO₂ + 2SO₂ gas environment at 650 ℃. Corrosion characteristics were characterized by weight gain, oxide layer thickness, scanning electron microscope, optical microscope, energy dispersive X-ray spectroscopy, and X-ray diffraction. T22 and T92 steel tended to stagnate oxide layer growth over time. Oxidation kinetics were analyzed using the data of oxide layer thickness, and a regression model was presented. The regression model was significantly acceptable. The corrosion rate between the two steels through the regression model showed significant difference. The T92 steel was approximately twice as large as the time exponent and showed very good corrosion resistance compared to the T22 steel. In both steels, the oxide layer mainly formed a Fe-rich oxide layer composed of hematite (Fe₂O₃), magnetite (Fe₃O₄), and spinel (FeCr₂O₄). Sulfide segregation occurred in the oxide layer due to SO₂ gas. However, the locations of segregation for the T22 and T92 steel were different.

• Journal of Welding and Joining
• /
• v.28 no.1
• /
• pp.41-46
• /
• 2010

The low alloy-steel material(1.0Cr-0.5Mo, SA213T12), which has widely been used for the waterwall tube in the conventional power plant, do not have enough creep rupture strength for waterwall tubes of the Ultra-supercritical(USC) boilers. According to this reason, the high-strength low alloy-steel(2.25Cr-1.0Mo, SA213T22) has newly been adopted for the waterwall tube in the USC boilers. This paper presents failure analysis on weld-joint of the waterwall tubes in USC boilers. Visual inspections were performed to find out the characteristics of the fracture. Additionally both microscopic characteristics and hardness test were carried out on failed tube samples. Failures seem to happen mainly because the welding process has not been conducted strictly.(preheating, P.W.H.T and so forth). Thus, this paper has the purpose to describe the main cause of the poor welding process and to explain how to prevent similar failures in those weld-joints.

• Korean Journal of Animal Reproduction
• /
• v.20 no.2
• /
• pp.163-170
• /
• 1996

The effect of several potential antioxidants and amino acids were examined as a means of increasing the development of in vitro matured and in vitro fertilized oocytes into morulae or blastocysts. Bovine embryos developed to the 2~8 cell stage after in vitro fertilization were cultured for 5 to 6 days at 39$^{\circ}C$ in CR1aa containing varing concentraton of the antioxidants and amino acid in a gas phase consisting of 5% CO2, high humidified air. At 5~6 days, embryo developments were reduced, and embryos were fixed and stained with Hochest 33342 DNA stain to facilitate counting of cells. In experiment 1, the proportion of embryos developed to morulae and blastocysts in CR1aa containing 1mM, 2.5mM taurine (22.6% and 20.4%) was slightly higher than those of 0, 5 and 10mM Taurine (5.7, 5.7 and 3.9%, P<0.05). In experiment 2, addition of glutathione did not improve blastocyst development (P>0.05). In experiment 3, concentations of superoxide dismutase(SOD) ranging from 300 to 1,000 U did not affect the propotion of embryos developing into blastocysts (P>0.05). In experiment 4, addition of 250 U catalase(38.5%) was slighty higher than those of 0, 500 and 1,000U. In experiment 5, the proportion of embryo developed beyond morula stage in CR1aa with taurine plus EDTA was slighty higher than other treatments(15.7, 26.0 and 29.2%), there were no significantly increases in cell number among treatments(P>0.05). These results are indicating that antioxidants and amino acids can increase the proportion of embryos that develop into morulae and blastocysts, but did not increas in cell number of blastocysts.

• The Korean Journal of Malacology
• /
• v.22 no.2
• /
• pp.167-173
• /
• 2006

The embryos of marine bivalves have been commonly used in bioassays for quality assessments of marine environments. Although several standard protocols for the developmental bioassay of bivalves have been proposed, only a few trials for application of these protocols in environmental assessments or for the development of a new protocol with Korean species have been conducted. As such, there is a strong need to establish standard bioassay protocols with bivalves commonly found in Korean waters. To determine the sensitivity of Mytilus galloprovincialis to establish a standard bioassay, their fertilized eggs were exposed to six metals (Ag, Cd, Cr, Cu, Ni, and Zn). The order of biological impact was Ag > Cu > Ni > Zn > Cr > Cd and their lowest observed effective concentration were 5, 16.4, 25.4, 142, 187 and 1,500${\mu}g/l$, respectively. The proportion of normal larvae appeared to decrease linearly with the logarithm of each toxicant concentration within the tested range. The average values of median effective concentrations $(EC_{50})$ from the triplicate experiments for Ag, Cd, Cr, Cu, Ni, and Zn were 6.8, 1,797, 786, 16.6, 68.1, and 139.2${\mu}g/l$, respectively. There was a more than 100-fold difference in $EC_{50}$ values of Cu and Cd. The value of $EC_{50}$ or median lethal concentration of Cu was within the range observed for other bivalve developmental bioassays. The overall sensitivity of M. galloprovincialis in the present developmental bioassay was also similar to that of other marine organisms commonly used in aquatic bioassays (e.g. sea urchins, oysters). Hence, the bioassay using the embryo of M. galloprovincialis is considered to be a useful tool to monitor and evaluate the quality of marine aquatic environments.