• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.225-230
• /
• 2009

From the view point of railway vehicle dynamics, the interaction between wheel and rail have an huge effect on the behavior of the vehicle. This phenomenon is an unique motion, only for railway vehicles. Furthermore, close investigation of the backgrounds of the interaction is the key to estimate the dynamic behavior of the vehicle, successfully. To evaluate the model including flexible bodies such as car body and catenary system of the next generation express train, it is necessary to develop proper dynamic solver including a wheel rail contact module. In this study, wheel-rail contact module is developed using the general purpose dynamic solver. First of all, the procedure for calculation of the wheel-rail contact force has been established. Generally, yaw angle of the wheelset is ignored. Sets of information are summarized as tables and splined for further uses. With this information, normal force and creep coefficient can be extracted and used for FASTSIM algorithm, which has been shown good reliability over years. Normal force and longitudinal, lateral force at the contact surface are also calculated. Those data are verified by commercial railway simulation program 'VAMPIRE'. This procedure and program can offer a basic process for estimation of the dynamic behavior and wear of the wheel-rail system, even while running on the curved rail. Finally, multi-dimensional inspection tool will be developed including the prediction of the derailment.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.3
• /
• pp.175-179
• /
• 2022

Magnetic arc extinguishing technology is effective as an extinguishing device for low-voltage direct current (DC) circuit breakers with a resistive load of ≤4 kW. The separation distance between the magnet and the electrical contact must be shortened to increase the magnetic arc extinguishing force. However, if the magnet is installed too close to the electrical contact points, the magnet is exposed to high temperatures due to the arc current generated when the load current is cut off and the magnetism is lost. To solve this problem, the effective magnetic flux density at the electrical contact can be maintained high by placing the arc extinguishing magnet in a tandem structure with the electrical contact point between them, and the proper separation distance between the contact points and the magnet can be maintained. In addition, an electric arc extinguishing technology that emits arc energy using a series circuit of diode and resistor is used to suppress the continuous arc voltage generated by the inductive load. For the proposed circuit breaker, the breaking characteristics are analyzed through the breaking test for the DC load of the 760 V level, the load power of 4 kW, and the time constant of 5 ms, and an appropriate arc extinguishing design guideline is proposed.

• Journal of IKEEE
• /
• v.26 no.4
• /
• pp.681-685
• /
• 2022

Including the COVID-19 crisis, humanity is constantly exposed to viral infections, and efforts are being made to prevent the spread of infection by quickly isolating infected people and tracing contacts. Passive epidemiological investigations that confirm contact with an infected person through contact have limitations in terms of accuracy and speed, so automatic tracking methods using various digital technologies are being proposed. This paper verify contact by utilizing Bluetooth Low Energy (BLE) technology and present an algorithm that identifies close contact through analysis and correction of RSSI (Received Signal Strength Indicator) values. Also, propose a system that can prevent the spread of viruses in a centralized server structure.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.47 no.1
• /
• pp.123-136
• /
• 2023

To develop smart sportswear capable of measuring biometric data, we created a close-fitting pattern using two- and three-dimensional (2D and 3D, respectively) methods. After 3D virtual fitting, the tightness of each pattern was evaluated using image processing of contact points, mesh deviation, and cross-sectional shapes. In contact-point analysis, the 3D pattern showed high rates of contact with the body (84.6% and 93.1% for shirts and pants, respectively). Compared with the 2D pattern, the 3D pattern demonstrated closer contact at the lower chest, upper arm, and thigh regions, where electrocardiography and electromyography were primarily carried out. The overall average gap was also lower in the 3D pattern (5.27 and 4.66 mm in shirts and pants, respectively). In the underbust, waist, thigh circumference, and mid-thigh circumference, the cross-section distance between clothing and body was showed a statistically significant difference and evenly distributed in the 3D pattern, exhibiting more closeness. The tightness and fit of the 3D smart sportswear sensor pattern were successfully evaluated. We believe that this study is critical, as it facilitates the comparison of different patterns through visualization and digitization through 3D virtual fitting.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.125-129
• /
• 1996

This paper presents the haptic rendering algorithm which gives the feel information to the operator by manipulating a virtual tool with a haptic device in the simulated environment. The movement of a virtual tool grasped by the operator, which is modeled as a square is displayed in the graphic screen of a computer and the virtual environment is modeled as deformable thin film. When the tool contacts with the virtual environment, the operator is forced to feel the contact and the feature of the deformed virtual environment through the torque control of th haptic device. Contact situations are modeled as close as to the reality considering friction, elasticity and multiple contacts. Several experiments are conducted and the effectiveness of the proposed algorithm is confirmed.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.3
• /
• pp.106-111
• /
• 2020

In this paper, we propose the non-contact gesture recognition system and algorithm using proximity-based sensors. The system uses four IR receiving photodiode embedded on a single chip and an IR LED for small area. The goal of this paper is to use the proposed algorithm to solve the problem associated with bringing the four IR receivers close to each other and to implement a gesture sensor capable of recognizing eight directional gestures from a distance of 10cm and above. The proposed system was implemented on a FPGA board using Verilog HDL with Android host board. As a result of the implementation, a 2-D swipe gesture of fingers and palms of 3cm and 15cm width was recognized, and a recognition rate of more than 97% was achieved under various conditions. The proposed system is a low-power and non-contact HMI system that recognizes a simple but accurate motion. It can be used as an auxiliary interface to use simple functions such as calls, music, and games for portable devices using batteries.

• English Language & Literature Teaching
• /
• no.1
• /
• pp.1-20
• /
• 1995

Nowadays in Korea the subject of English education has been rising as one of the essential matters which need to be emphasized, reorganized, and thus refined. From the history of about one century to the current, English education may be compared to an adolescent who should be paid much more attention to grow as an independent adult. Although we recognize that there was much improvement in the past age of English education, a lot of assignments to solve await us. This study aims to suggest a recipe for optimal learning in English classes by linking theory with practice: First, the nation-wide academic associations of English teaching should act more energetically and cooperatively than ever. They need further specialization, dynamic participation, and systematic organization. At the same time the academic journals of their own should be publicized broadly, internationally as well as nationally. Second, there should be close contact and discussion between professors and secondary-school teachers. To achieve better learning in English classes, an effective cycle of equilibrium ought to be maintained by combining theory with practice. For example, language institute in universities/colleges can serve instructional programs such as lectures, colloquiums, and intensive courses for conversation. Third, native speakers of English should be positively utilized. Teachers had better keep close contact with native speakers as frequently as possible if they want to become fluent or at least acceptable speakers in English. Teachers may also use native speakers as aides in their classes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.6
• /
• pp.871-883
• /
• 1997

Kinetodynamics of a cam driving slider mechanism consists of kinematic analysis and force analysis. The kinematic analysis is to determine the kinematic characteristics of a cam driving mechanism and a slider mechanism. The force analysis is to determine the joint forces of links, the contact forces of the cam and follower, and the driving torque of a main shaft. This paper proposes a close loop method and a tangent substitution method to formulate the relationships of kinematic chains and to calculate the displacement, velocity and acceleration of the cam driving slider mechanism. Also, and instant velocity center method is proposed to determine the cam shape from the geometric relationships of the cam and the roller follower. For dynamic analysis, the contact force and the driving torque of the cam driving slider mechanism are calculated from the required sliding forces, sliding motion and weight of the slider.

• Journal of the Korean Institute of Gas
• /
• v.11 no.1 s.34
• /
• pp.34-39
• /
• 2007

In this paper, the FEM result has been presented for a sealing safety between a valve packing and a valve seat during a open and close operation in a LPG cylinder. The sealing operation of a LPG valve is completed when the valve packing in which is made by a nylon-66 polymer is to stop a LP gas flow, which flows out from the outlet of a brass pipe in a LPG cylinder. The contact sealing mechanism of the valve may be classified by a flat contact of an unused valve packing and a circular groove contact of an used valve packing in a current LPG valve. Based on the FEM and experimental investigations the sealing force, 4.9 MPa for a flat contact mode of the unused valve packing is a little high compared to that of the used valve packing, which shows a circular groove contact geometry against a valve seat. But these sealing pressures for two contact modes are very low compared to the ultimate strenath 83 MPa of the nylon-66 and this may be designed with a excess strength of the valve.

• Korean Journal of Materials Research
• /
• v.12 no.12
• /
• pp.918-923
• /
• 2002

In this work, CdTe films were deposited on CdS/ITO/glass substrate by a close spaced sublimation (CSS) method. A $Cu_2$Te layer was deposited on the CdTe film by evaporating $Cu_2$Te powder. Then the samples were annealed for p+ ohmic contact. TEM and XRD analysis showed that $CdTe/Cu_2$Te interface exhibited different forms with various annealing temperature. A good p+ ohmic contact was achieved when the annealing temperature was between $180^{\circ}C$ to $200^{\circ}C$. Best cell efficiency of 12.34% was obtained when post annealing temperature was $200^{\circ}C$ for 5 min. Thermal stress test of the CdS/CdTe cells with carbon back contact showed that the $Cu_2$Te contact was stable at $50^{\circ}C$ in $N_2$ and was slowly degraded at $100^{\circ}C$ in $N_2$. In comparison to the conventional carbon contact, the $Cu_2$Te contact showed a better thermal stability.