• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.3
• /
• pp.232-239
• /
• 2010

By using the clock timing control at transmitter (TX), the crosstalk-induced jitter (CIJ) is compensated for in the 2-bit parallel data transmission through the coupled microstrip lines on printed circuit board (PCB). Compared to the authors' prior work, the delay block circuit is simplified by combining a delay block with a minimal number of stages and a 3-to-1 multiplexer. The delay block generates three clock signals with different delays corresponding to the channel delay of three different signal modes. The 3-to-1 multiplexer selects one of the three clock signals for TX timing depending on the signal mode. The TX is implemented by using a $0.18\;{\mu}m$ CMOS process. The measurement shows that the TX reduces the RX jitters by about 38 ps at the data rates from 2.6 Gbps to 3.8 Gbps. Compared to the authors' prior work, the amount of RX Jitter reduction increases from 28 ps to 38 ps by using the improved implementation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12C
• /
• pp.249-254
• /
• 2001

A receiver ASIC for fiber optic modules of STM-1 optical communication has been fabricated with 0.65 $\mu\textrm{m}$ CMOS technology. The ASIC has a limit amplifier circuit for the 155.52 Mbps data reshaping, and a clock extraction circuit for the 155.52 MHz clock recovery. The ASIC has an acquisition aid and LOS monitoring circuit for properly operation with near 155.52 MHz clock frequency in case of the data loss due to transmission line open or data transfer fail. Measured results show that the circuit reshapes data from 5 mV to 1 V wide range of input voltage condition, add it recovers system clock with stable on any condition.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.309-314
• /
• 2006

In general DGPS system, the correction message is transferred to users by wireless modem. To cover wide area, many DGPS station should be needed. And DGPS users must have a wireless modem that is not necessary in standalone GPS. But SBAS users don't need a wireless modem to receive DGPS corrections because SBAS correction message is transmitted from the GEO satellite by L1 frequency band. SBAS signal is generated in the GUS(Geo Uplink Subsystem) and uplink to the GEO satellite. This uplink transmission process causes two problems that are not existed in GPS. The one is a time delay in the uplink signal. The other is an ionospheric problem on uplink signal, code delay and carrier phase advance. These two problems cause ranging error to user. Another critical ranging error factor is clock synchronization. SBAS reference clock must be synchronized with GPS clock for an accurate ranging service. The time delay can be removed by close loop control. We propose uplink ionospheric error correcting algorithm for C/A code and carrier. As a result, the ranging accuracy increased high. To synchronize SBAS reference clock with GPS clock, I reviewed synchronization algorithm. And I modified it because the algorithm didn't consider doppler that caused by satellites' dynamics. SBAS reference clock synchronized with GPS clock in high accuracy by modified algorithm. We think that this paper will contribute to basic research for constructing satellite based DGPS system.

• ETRI Journal
• /
• v.21 no.3
• /
• pp.1-5
• /
• 1999

A clock and data recovery circuit with a phase-locked loop for 10 Gb/s optical transmission system was realized in a hybrid IC form. The quadri-correlation architecture is used for frequency-and phase-locked loop. A NRZ-to-PRZ converter and a 360 degree analogue phase shifter are included in the circuit. The jitter characteristics satisfy the recommendations of ITU-T. The capture range of 150 MHz and input voltage sensitivity of 100 mVp-p were showed. The temperature compensation characteristics were tested for the operating temperature from -10 to $60^{\circ}C$ and showed no increase of error. This circuit was adopted for the 10 Gb/s transmission system through a normal single-mode fiber with the length of 400 km and operated successfully.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.829-832
• /
• 2005

This paper describes a wide-range dual-loop Delay Locked Loop (DLL) using Voltage Controlled Delay Line (VCDL) based on Transmission Gate(TG) inverters. One loop is used when the minimum VCDL delay is greater than a half of $T_{REF}$, the reference clock period. The other loop is initiated when the minimum delay is less than $0.5{\times}T_{REF}$. The proposed VCDL improves the dynamic operation range of a DLL. The DLL with a VCDL of 10 TG inverters provides a lock range from 70MHz to 700MHz when designed using $0.18{\mu}m$ CMOS technology with 1.8 supply voltage. The DLL consumes 11.5mW for locking operation with a 700MHz reference clock. The proposed DLL can be used for high-speed memory devices and processors, communication systems, high-performance display interfaces, etc.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.11
• /
• pp.1144-1149
• /
• 2009

This paper deals with the time synchronization problem over SpaceWire links. SpaceWire is a standard for high-speed links and networks between spacecraft components, which was invented for better, cheaper, faster on-board data handling in spacecraft. The standard defines Time-Code for time distribution over SpaceWire network. When a Time-Code is transmitted, transmission delay and jitter is unavoidable. In this paper, a mechanism to remove Time-Code transmission delay and jitter over SpaceWire links is proposed and implemented with FPGA for validation. The proposed mechanism achieves high resolution clock synchronization over SpaceWire links, complies with the standard and can be easily adopted over SpaceWire network.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.62-65
• /
• 1998

This paper presents a method and implementation of the parallel distributed sample scrambler(DSS) in the cell-based ATM transmission environment. In the serial processing, it requires very high speed clock because the processing clock of the serial DSS is equal with the data transmission speed. In this paper, we develop a conversion method of the serial SRG(shift register generator) to 8bit parallel realization. In this case, it has a sample data processing problem which is a character of DSS. So, a theory of correction time movement is presented to solve this problem. We has developed a ASIC using this algorithm and verified the recommendation of ITU-T, I.432.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2004.11a
• /
• pp.60-60
• /
• 2004

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.10C
• /
• pp.987-992
• /
• 2002

In this paper, a new clock and data recovery circuit is proposed for the application of data communication systems requiring ㎓-range clock signals. The circuit is suitable for recovering NRZ data which is widely used for high speed data transmission in ㎓ ranges. The high frequency jitter is one of major performance-limiting factors in PLL, particularly when NRZ data patterns are used. A novel phase detector is able to suppress this noise, and stable clock generation is achieved. Futhermore, the phase detector has an adaptive delay cell removing the dead zone problem and has the optimal characteristics for fast locking. The proposed circuit has a convenience structure that can be easily extended to multi-channels. The circuit is designed based on CMOS 0.25㎛ fabrication process and verified by measurement result.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.2
• /
• pp.19-24
• /
• 2007

With recent advancement of high-speed, multi-gigabit data transmission capabilities, serial links have been more widely adopted in industry than parallel links. Since the parallel link design forces its transmitter to transmit both the data and the clock to the receiver at the same time, it leads to hardware's intricacy during high-speed data transmission, large power consumption, and high cost. Meanwhile, the serial links allows the transmitter to transmit data only with no synchronized clock information. For the purpose, clock and data recovery circuit becomes a very crucial key block. In this paper, a 5.4Gbps half-rate bang-bang CDR is designed for the applications of high-speed graphic DRAM interface. The CDR consists of a half-rate bang-bang phase detector, a current-mirror charge-pump, a 2nd-order loop filter, and a 4-stage differential ring-type VCO. The PD automatically retimes and demultiplexes the data, generating two 2.7Gb/s sequences. The proposed circuit is realized in 66㎚ CMOS process. With input pseudo-random bit sequences (PRBS) of $2^{13}-1$, the post-layout simulations show 10psRMS clock jitter and $40ps_{p-p}$ retimed data jitter characteristics, and also the power dissipation of 80mW from a single 1.8V supply.