• Environmental Engineering Research
• /
• v.15 no.1
• /
• pp.35-40
• /
• 2010

Bung Boraphet is the largest freshwater reservoir in Thailand. This study examined the accumulation of copper (Cu) and lead (Pb) in water, sediment and tissues of Asian clams (Corbicula sp.) within Bung Boraphet to assess the possible polluting effect of soil erosion and the dissolution of water soluble salts from the Nan River. Samples were collected from 12 study sites within Bung Boraphet between February and December 2008. The physicochemical parameters of the water including temperature, pH, turbidity, ammonia nitrogen, nitrate nitrogen, orthophosphates, biochemical oxygen demand, dissolved oxygen, Cu, and Pb were measured. The water in Bung Boraphet was found to be medium clean according to the surface water quality standard of Thailand. The levels of Cu and Pb in the water were low but heavy metals were detected at higher levels in the sediment and tissues of Corbicula sp. In the near future, management practices and regulator approaches for Cu and Pb contamination will be needed to protect the water in Bung Boraphet.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.17 no.3
• /
• pp.175-194
• /
• 2014

This study attempts to identify the spatial distributions of Achnanthes convergens, and elucidate the environmental factors that affect the Periphyton diatom habitat. Data in 250 points of Nakdong river basin are collected between April(primary) and September(secondary) 2012, with the National Institute of Environmental Research's support. We define "clean area" over 10% of Achnanthes convergens appearance, and the others as "non-clean areas". Spatial statistics of Kriging, Hotspot, LISA are used in this study. Results show that 1) 56 points are identified as clean areas in the primary survey, while 41 points are discovered in the following survey; 2) using water quality variables, density of turbidity(clean $101.83{\mu}s/cm$; non-clean $598.48{\mu}s/cm$) and conductivity(clean 1.95 NTU; nonclear 5.58 NTU) are five-fold lower in clean-areas; 3) Habitat and Riparian Factors in Nakdong basin illustrate that natural sand bar, diversity of velocity, sediment condition, levee material, riverside land affect Achnanthes convergens; 4) Hotspots of Achnanthes convergens are located in watersheds, including upper Andong Dam, upper Imha dam, Wi-cheon, Miryang river, Nam river and Hwang river whereas mainstream/downstream of Nakdong river and Keumho river watershed are shown as coldspots.

• Clean Technology
• /
• v.26 no.1
• /
• pp.39-54
• /
• 2020

This study analyzed the groundwater quality according to the depth and geological features in Gyeongsangnam-do area using groundwater quality monitoring network data to grasp the groundwater quality characteristics and to provide basic data for policy making on efficient groundwater management. Five hundred and three data sets were acquired from background water quality exclusive monitoring network in soil groundwater information system for five years (2013 ~ 2017). Except for the total coliforms and tracer items such as mercury, phenol, and others, the parameters of water quality were significant or very significant, depending on depth and geological features. As the depth got deeper, the average value of pH and electrical conductivity increased; water temperature, dissolved oxygen, oxide reduction potential, arsenic, total coliforms, and turbidity decreased; and total unfit rate for drinking water standards was lower. It was found that the sum of the positive and negative ions was the highest in the clastic sedimentary rock and the lowest in metamorphic rock. The total unfit rate for drinking water standards was the highest for metamorphic rocks, followed by clastic sedimentary rock and unconsolidated sediments and, finally, intrusive igneous rock with the lowest penetration. The Na-Cl water type, which indicated the possibility of contamination by external pollutants, appeared only at some points in shallow depths and in clastic sedimentary rocks.

• Clean Technology
• /
• v.15 no.1
• /
• pp.54-59
• /
• 2009

In this study, the separation of water/bitumen emulsion was investigated by chemical demulsification method. Motor oils (GS Caltex Deluxe Gold V 7.5W/30, Hyundai gear oil 85W/140) and asphalt (AP-5, KS M 2201, Dongnam Petrochemical MFG. Co.) were used as model oils in the preliminary experiments to effectively remove water from water/bitumen emulsion. The bitumen extracted from Canadian oilsands was used in this study. The water/oil emulsion was not separated without demulsifiers, and Hyundai motor oil showed higher efficiency of water separation at a low concentration of demulsifier compared with that for GS Caltex motor oil. However, as the concentration increased, the efficiency did not rapidly increase compared with that of GS Caltex motor oil. It was highly speculated that the water phase of Hyundai motor oil was not dispersed well compared with that of GS Caltex motor oil because the viscosity of Hyundai motor oil was much higher than that of GS Caltex motor oil. The demulsifier of higher HLB (hydrophilic - lipophilic balance) value had high separation efficiencies in water/oil emulsion. The TWEEN 20 (polyoxyethylene sorbitan monolaurate solution) showed better separation efficiency than other demulsifiers.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.3
• /
• pp.343-350
• /
• 2008

Many reports have warned of insufficient water supply in most countries in future and prospected providing safe and clean water become more difficult by lack of access to sustainable drinking water resources. Several facts and figures explained the impact by natural climate change and human activity results in the water scarcity and deterioration. Among many scientific solutions, the seawater desalination using a reverse osmosis membrane, so called SWRO (Seawater Reverse Osmosis) process, has been recognized as one of the most promising alternatives because of its stability and efficiency in producing large amount of drinking water from seawater through desalination by membrane filtration. Recently, in Korea, numerous researches are conducted to develop more productive and cost effective SWRO process for its wide implementation. The objective of this paper is to review the patents concerning SWRO technologies involving the plant engineering, maintenance including pretreatment of seawater and fouling control, module design, and mechanical units development for energy saving. The patents in Korea, U.S., Japan, Europe, and PCT were intensively researched and analyzed to provide the state of the art as well as leading edge technology on SWRO. This information can hopefully suggest meaningful guidelines on future research and development.

• Clean Technology
• /
• v.10 no.1
• /
• pp.47-51
• /
• 2004

현재 반도체 공정에서 사용되는 세정기술은 대부분이 1970년대 개발된 RCA 세정법인 과산화수소를 근간으로 하는 습식 세정으로, 표면의 입자를 제거하기 위한 SC-1 세정액은 강력한 산화제인 과산화수소에 의한 표면과 입자의 산화와 암모니아에 의한 표면의 에칭이 동시에 일어나 입자를 표면으로부터 분리시킨다. 금속 불순물을 제거하기 위한 SC-2 세정액은 염산과 과산화수소 혼합액을 사용하며 금속 불순물을 용해시켜 알칼리나 금속 이온을 형성하거나 용해 가능한 화합물을 형성시켜 제거한다. 또한 황산과 과산화수소를 혼합한 Piranha 세정액은 효과적인 유기물 제거제로서 웨이퍼에 오염된 유기물을 용해 가능한 화합물로 만들거나 과산화수소에 의해 형성되는 산화막내에 오염물을 포함시켜 불산 용액으로 산화막을 제거할 때 함께 제거된다. 최근 금속과 산화막을 동시에 제거하기 위해 희석시킨 불산에 과산화수소를 첨가한 세정공정이 사용되고 있으며 불산에 의해 표면의 산화막이 제거될 때 산화막내에 포함된 금속 불순물을 동시에 제거시킬 수 있다. 그러나 이와 같이 습식세정액 내에 공통적으로 포함되어 있는 과산화수소의 분해는 그만큼 가속화되어 사용되는 화학 약품의 양이 그만큼 증가하게 되고 조작하기 어려운 단점도 있다. 이를 해결하기 위해 환경친화적인 관점으로 화학약품의 사용을 최소화하는 등 RCA세정을 보완하는 연구가 계속 진행되고 있다. 본 연구에서는 RCA세정법을 환경적으로 대체할 수 있는 세정에 사용되는 전리수의 pH변화에 따른 전리수 분석을 하였다. 전리수의 제조를 위하여 전해질로는 NH4CI (HCI:H2O:NH4OH=1:1:1)를 사용하였다. pH 11 이상, ORP -700mV~-850mV인 환원수와 pH 3 이하, ORP 1000mV~1200mV인 산화수를 제조하였으며, 초순수를 첨가하여 pH 7.2와 ORP 351.1mV상태까지 조절하였다. 이렇게 만들어진 산화수와 환원수를 시간 변화와 pH 변화에 따라 Clean Room 안에서 FT-IR과 접촉각 측정기로 실험하였다. FT-IR분석에서 산화수는 pH가 높아질수록, 환원수는 낮아질수록 흡수율이 낮아졌다. 접촉각 실험에서는 산화수의 pH가 높아질수록 환원수의 pH가 낮아질수록 접촉각이 커짐을 확인하였다. 결론적으로 전리수를 이용하여 세정을 하면, 접촉성을 조절할 수 있어 반도체 세정을 가능하게 할 수 있으며, 환경친화적인 결과를 도출할 것으로 전망된다.

• Clean Technology
• /
• v.27 no.1
• /
• pp.39-46
• /
• 2021

A road structure washing vehicle equipped with a 4 HP, 80 LPM ultrafine bubble generator was used to clean a tunnel wall and the surface of the surrounding structure, consisting of concrete and tiles, in a heavy traffic area around an apartment complex in the city. Ultrafine bubbles were generated by supplying air at 2 to 3 LPM and using a specially designed nozzle, whereas fine bubbles made by an impeller in a gas-liquid mixing self-priming pump were produced with an average diameter of 165.4 nm and 6.81 × 107 particles mL-1. Using a high pressure washer gun that can perform high-pressure cleaning at 150 bar and 30 LPM, ultrafine bubbles were used to wash dust adsorbed on the surface of the road structures. The experimental analysis was divided into before and after washing. The samples were analyzed by applying ISO 8502-3 to measure surface contamination of dust adsorbed on the surface. Using the transparent tape attached to the surface, the removal rate was calculated by measuring the weight of the dust, and the number of particles was calculated using the gravimetric method and the software, ImageJ. The results of the experiment showed that the number of dust particles adsorbed on the tile wall surface before and after washing were 3,063 ± 218 particles mL-1 and 20 ± 5 particles mL-1, respectively, with weights of 580 ± 82 mg and 13 ± 4 mg. Particles on the surface of the concrete structure before and after washing were 8,105 ± 1,738 particles mL-1 and 39 ± 6 particles mL-1, respectively, with weights of 1,448 ± 190 mg and 118 ± 32 mg.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.9
• /
• pp.977-982
• /
• 2013

Blades of wind energy plants are exposed to external shocks or internal cracks during operation. Furthermore, the blade surfaces can be contaminated by substances such as dust, blood of birds, salt or insects which can decrease the electricity generation efficiency significantly. For this reason, many blade cleaning companies started to appear and a variety of methods for cleaning were suggested. Despite these diverse methods, there has been no study to investigate how effectively to clean the substances in quantitative manner. In this paper, the cleaning efficiency of two rotor blade cleaning methods, brush and water-jet, is examined through experiments by changing operating parameters. Then, the optimal operating conditions for both methods are derived.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.715-718
• /
• 2001

This study uses traditional alum coagulation and sedimentation process to treat CMP wastewater from cleaning after polishing. The primary goal is to successfully recycle both solid fines and water for semiconductor manufacturing. Results indicated that CMP wastewater may be successfully treated to recover clean water and fine particles by alum coagulation. The optimum operating conditions for coagulation are as fellowing: alum dosage of 10 ppm, pH at 5, rapid mixing speed at 800 rpm, 5 min rapid mixing time, and long slow mixing time. The treated water with low turbidity and an average residual aluminum ion concentration of 0.23 ppm may be considered for reuse. The settled sludge after alum coagulation contains mainly SiO$_2$particle with a minor content of aluminum (1.7 wt%) may be considered as raw materials for glass and ceramic industry.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2003.11a
• /
• pp.25-33
• /
• 2003

It summarized about the application of the membrane technology in thermochemical water-splitting iodine-sulfur process that was hydrogen production using the nuclear heat from the High Temperature Gas-Cooled Reactor (HTGR). Thermochemical water-splitting hydrogen production method using the high temperater nuclear thermal energy could be realized and remained to be solved the investigation subject. And, it is possible for mass-production of hydrogen such as one of the clean energy in future.