• The Journal of Engineering Geology
• /
• v.18 no.4
• /
• pp.423-431
• /
• 2008

In general, water-saturated silt or clay alluvium is characterized with relatively low-resistivity. Thus we often encountered the problem that such a low-resistivity layer is misguided to be good aquifer of high-permeability and low-resistivity in the development of groundwater. This research was conducted with an emphasis on the identification of saturated silt or clay layer from the aquifer by performing the laboratory experiment of IP and resistivity methods on the various materials consisting of alluvium aquifer. Silt or clay layer is found to be characterized with the higher chargeability zone, compared to the sand layer. Regarding the mixture of sand and clay, the higher clay volume, the lower resistivity and the higher chargeability. Subsequently chargeability decreases.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.1042-1050
• /
• 2008

In this study, SCP method was used by purpose to improve loose sand and soft clay that is drilled Sand Compaction Pile in underground. Settlement behavior of field analyzed through SCP method. When sand Compaction Pile drilled in clay, forming composite ground that foundation and Sand Compaction Pile behavior. According to SCP method can expect bearing capacity improvement, Settlement reduction, lateral flow protection. SCP increase the consolidation settlement of ground and it reduce settlement for that purpose increase liquefaction resistance, lateral Resistance. Because SCP had been widely used for sand. Area of Inchon-A by sand compose clay and silt to upper Ground and compose soft clay to under ground. After pre-loading, it measured settlement by extensometer and settlement extensometer that purpose of ground improvement with 13% in replacement ratio. The result analyzed settlement behavior is similar to Multi-layered Ground that it happened to elastic settlement at upper ground and to consolidation settlement at under ground.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.747-752
• /
• 2003

This study was carried out to understand the stratigraphy and depositional environment of clayey soils that distributed in the Gadeok-do area, Kimhae plain (Nakdong estuary). For the study, SPT core sampling and magnetic susceptibility analysis were conducted. Soils in study area is classified into five sedimentary facies ascending order; sand/gravel. clay, sand/gravel, clay, interbedded sand and silty clay. Analysis of magnetic susceptibility for Gadeok-do clayey soil reveals that depositional process and environment can be divided into upper, middle and lower layer, and they are closely related to the sea level change since late Quaternary.

• Journal of The Geomorphological Association of Korea
• /
• v.25 no.4
• /
• pp.77-88
• /
• 2018

Wetlandsis developing on the lava plateau in Eundae-ri, even though there are no majorstreams into this area. As a result of drilling, 1~2m clay layer is founded under the superficial formations of the wetland, which are the main reasons for formation of the wetlands by limiting vertical drainage. The clay layer's Granulometry/XRD show very different characteristics from in situ weathering of basalt, and since 2~3cm of sand layer exist within the profile, the clay layer seems to be supplied and deposited from outside through surface/sheet flows. To keep the wetlands sustainably, the supply of water into the wetlands has to be increased by restoring the surface/sheet flow which is limited or deformed by pavement road.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.7
• /
• pp.35-45
• /
• 2016

Estimation of vertical bearing capacity is critical in the design of bucket foundation used to support offshore structure. Empirical formula and closed form solutions for bucket foundations in uniform sand or clay profiles have been extensively studied. However, the vertical bearing capacity of bucket foundations in alternating layers of sand overlying clay is not well defined. We performed a series of two-dimensional axisymmetric finite element analyses on bucket foundations in sand overlying clay soil, using elasto-plastic soil model. The load transfer mechanism is investigated for various conditions. Performing the parametric study for the friction angles, undrained shear strengths, thickness of sand layer, and aspect ratios of foundation, we present the predictive charts for determining the vertical bearing capacities of bucket foundations in sand overlying clay layer. In addition, after comparing with the finite element analysis results, it is found that linear interpolation between the design charts give acceptable values in these ranges of parameters.

• Journal of Conservation Science
• /
• v.32 no.1
• /
• pp.75-88
• /
• 2016

In this study, 5 mural paintings in the Buddhist temples of Joseon era were researched for component analysis on the soil contained in the walls. The results of particle size analysis showed that the ratio of particle contents were different in each layer. In the finishing layer, the distribution of the middle sand fraction is higher than that of the middle layer. The results of XRD analysis showed that quartz, feldspar, and clay mineral are the main components of sand, suggesting similar mineral composition to that of ordinary soil component. It seems weathered rocks were used for construction of the walls. The main chemical components detected from EDX analysis were Si, Al, Fe, and K. Also the SEM images showed sand or clay sized minerals. In conclusion, the walls of the buddhist mural paintings in Joseon Dynasty had been constructed by using the loess, and had been produced by using mixture of clay and sand particles of different sizes for each layer. This study identified the characteristics of the materials and the manufacturing technologies used on the walls of mural paintings of Buddhist temples in Joseon era.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.706-713
• /
• 2004

This paper introduced an alternative method called USCP (Unpenetrated Sand Compaction Pile). In USCP, the toe of the sand pile does not reach to the lower supporting layer. Hence it is possible to reduce the amount of sand required. However, the degree of improvement could not be the same as SCP. Effective soil improvement, nevertheless, might be possible by combining both methods. In this paper, an improved method that cross over both SCP and USCP was discussed. And in order to verify applicability to a clay layer, consolidation behaviors with different conditions were analyzed and compared using FEM(Finite Element Method) based on the elasto-viscosity theory. From the results, it is concluded for the characteristic of settlement of USCP that the lower degree of replacement and the smaller ratio of penetration($H_d/H$), the larger is the settlement of the lower part of the clay layer comparing to the layer with no improvement. It is also concluded that the ratios of allotment of stress (m) calculated from the final settlements with 30% of degree of replacement are $1.8{\sim}3.3$ for $H_d/H=lOO%,\;1.8{\sim}4.0\;for\;H_d/H=75%,\;and\;1.8{\sim}3.8\;for\;H_d/H=50%$. Besides, the ratio of allotment of stress decreased as the degree of replacement decreased.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.11
• /
• pp.17-25
• /
• 2011

In this study, we considered the bearing capacity of strip footing over clay layers partially replaced by sand. The FEM analysis is performed to calculate the ultimate bearing capacity. Partial replacement is defined by multiples of footing width(B) and inclination of sides. The cases(B'=inf.) of sand layers equal to clay layers are preferentially conducted. The baring capacity of B'=inf. is comparative value for bearing capacity of partial replacement layers. ${\beta}$ is the ratio of ultimate bearing capacity of B'=inf and partial ultimate bearing capacity replacement. ${\beta}$ is used to analyze the characteristic of bearing capacity of clay layers partially replaced by sand. Each of the three undrained shear strengths of clay and friction angles of sand is considered. The result of this analysis shows that ${\beta}$ depends on sand depth.

• Journal of Conservation Science
• /
• v.38 no.4
• /
• pp.334-346
• /
• 2022

The manufacturing technique was studied through the structure and material characteristics of the walls and the painting layers of the Avalokitesvara Bodhisattva mural of Geungnakjeon Hall, Daewonsa Temple. The mural is painted and connected to the earthen wall and the Junggit, and the wall is composed of wooden laths as a frame, the first and middle layers, the finishing layer, and the painting layer. The first layer, middle layer, and finishing layer constituting the wall were made by mixing weathered soil and sand. It was confirmed that the first layer had a high content of loess below silt, and the finishing layer had a high content of fine-sand and very fine sand. For the painting layer, a ground layer was prepared using soil-based mineral pigments, and lead white, white clay, atacamite, minium, and cinnabar (or vermilion) pigments were used on top of it. The Avalokitesvara Bodhisattva mural was confirmed to belong to a category similar to the soil-made buddhist mural paintings of Joseon Dynasty. However, it shows characteristics such as a high content of fine sand in the finishing layer and overlapping over other colors. Such material and structural characteristics can constitute important information for future mural conservation status diagnoses and conservation treatment plans.

• Journal of Conservation Science
• /
• v.31 no.1
• /
• pp.1-11
• /
• 2015

Seated Amitabha Triad at Muwisa Temple (Treasure No. 1312) had been known as wooden Buddha statue, but a precise safety inspection revealed that the statue is terracotta Buddha statue made with clay. The clay layer of Amitabha Triad was conserved due to its severe damage. In this study, experiments were conducted to produce the most appropriate filler for the conservation treatment of the seated Amitabha Triad. Mixed clay samples with various ratios were produced and surface hardening state, crack, color change, and shrinkage of the samples during dry process were measured. Loess, fine sand powder, and cotton were used to produce the mixed clay for the filler with six different ratios and then 12 different concentration glues made with glutinous rice glue, Pachymeniopsis Elliptica glue, and animal glue were added as adhesives. Total 72 types of samples were prepared and comparative study was conducted. As a result, when the mixed clay contains 2.5% cotton compared to the weight per cent of loess and fine sand powder and also loess and fine sand in the mixed clay have a 15:1 ratio, the mixed clay had the lowest shrinkage. Animal glue is considered as an appropriate glue since it had small color change, low physical property change and shringkage. Therefore, mixed clay (loess:fine sand=15:1) mixed with 15ml animal glue is likely to be a suitable filler for conservation treatment of the seated amitabha triad at the Muwisa Temple.