• Journal of Ocean Engineering and Technology
• /
• v.25 no.6
• /
• pp.110-115
• /
• 2011

Numerouslong-term consolidation and secondary compression settlements may occur in Busan clay, which is astructured soft clay and consists of a thick clay deposit. As a surcharge load is applied to soils, soils experience different stress paths with depth. Therefore, it is necessary to study the long-term consolidation behavior of Busan clay considering stress conditions such as OC or NC states. In this study, a series of long-term consolidation tests were performed to investigate the consolidation characteristics of Busan clay for 20 days. The undisturbed clay samples were taken from 3 sites located in the Nakdong River estuary. The results showed that the creep rate of the Busan clay gradually decreased with time, which indicated that the secondary compression settlement decreased with time. In addition, the experimental results for 3 samples showed that the ratios were about 0.0363 and 0.051, respectively.

• Geomechanics and Engineering
• /
• v.15 no.2
• /
• pp.729-738
• /
• 2018

Soft clay soils due to their various geotechnical problems, stabilized with different additives. Traditional additives such as cement and lime will not able to increase the soil strength properties significantly. So, it seems necessary to use new additives for increasing strength parameters of soft clay soils significantly. Among the new additives, epoxy resins have excellent physical and mechanical properties, low shrinkage, excellent resistance to chemicals and corrosive materials, etc. So, in this research, epoxy resin used for stabilization of soft clay soils. For comprehensive study, three clay soil samples with different PI and various clay mineral types were studied. A series of uniaxial tests, SEM and XRD analysis conducted on the samples. The results show that using epoxy resin increases the strength parameters such as UCS, elastic modulus and material toughness about 100 to 500 times which the increase was dependent on the type of clay minerals type in the soil. Also, In addition to water conservation, the best efficiency in the weakest and most sensitive soils is the prominent results of stabilization by epoxy resin which can be used in different climatic zones, especially in hot and dry and equatorial climate which will be faced with water scarcity.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.27 no.3
• /
• pp.109-113
• /
• 1999

The objective of this research was to develop growth media for artificial ground by blending calcined clay and coconut peat. To achieve this, aggregates of clay particles were mixed with disel oil and heated to high temperature(1150~120$0^{\circ}C$) to expand clays. The particle sizes of expanded clay were controlled to 2~5mm in diameter. Then expanded clayes were mixed with coconut peat and changes of soil physicochemical properties and their effect on plant growth of Hedera L. were determined. The infiltration rate of calcined clay was very high, but the water holding capacity, the cation exchange capacity(CEC), and the nutrient contents were low. The characteritics of coconut peat was vice verse to calcined clay. This indicates that the mixture of calcined clay and coconut peat have the better characteristics than each material. As compared to mineral soil, the infiltration rate, the water holding capacity, the CEC and the nutrient contents increased, but bulk density decreased to about 1/4. And, Hedera L. grown in the mixture of calcined clay and coconut peat(6:4, v/v) had higher plant height, longer leaf length, more total number of leaves per plant and fresh weight than that grown in mineral soil, but statistical differences were not observed between two treatments.

• Korean Journal of Agricultural Science
• /
• v.44 no.2
• /
• pp.181-187
• /
• 2017

The use of practical management factors to maximize pig health improvement cannot guarantee freedom from diseases. Moreover, because of health safety concerns, the use of antibiotics has been restricted in livestock, including pigs. Therefore, the swine industry has been looking for various alternatives to antibiotics to improve pig's health and performance. Clay is a dietary factor generally accepted for improving pig health. It is a naturally occurring material and is primarily composed of fine-grained minerals. It has a specific structure with polar attraction. Because of this structure, clay has the ability to lose or gain water reversibly. In addition, clay has beneficial physiological activities. First, clay has anti-diarrheic and antibacterial effects by penetrating the cell wall of bacteria or inhibiting their metabolism. Second, it can protect the intestinal tract by absorbing toxins, bacteria, or even viruses. When added to the diet, clay has also been known to bind some mycotoxins, which are toxic secondary metabolites produced by fungi, namely in cereal grains. Those beneficial effects of clay can improve pigs' health and performance by reducing pathogenic bacteria, especially pathogenic Escherichia coli, in the intestinal tract. Therefore, it is suggested that clay has a remarkable potential as an antibiotics alternative.

• Nuclear Engineering and Technology
• /
• v.48 no.5
• /
• pp.1230-1236
• /
• 2016

This study aims to determine the effect of fly ash with a high replacing ratio of clay on the radiation shielding properties of bricks. Some interaction parameters (mass attenuation coefficients, half value layer, effective atomic number, effective electron density, and absorption efficiency) of clay fly ash bricks were measured with a NaI(Tl) detector at 661.6 keV, 1,173.2 keV, and 1,332.5 keV. For the investigation of their shielding behavior, fly ash bricks were molded using an admixture to clay. A narrow beam transmission geometry condition was used for the measurements. The measured values of these parameters were found in good agreement with the theoretical calculations. The elemental compositions of the clay fly ash bricks were analyzed by using an energy dispersive X-ray fluorescence spectrometer. At selected energies the values of the effective atomic numbers and effective electron densities showed a very modest variation with the composition of the fly ash. This seems to be due to the similarity of their elemental compositions. The obtained results were also compared with concrete, in order to study the effect of fly ash content on the radiation shielding properties of clay fly ash bricks. The clay fly ash bricks showed good shielding properties for moderate energy gamma rays. Therefore, these bricks are feasible and eco-friendly compared with traditional clay bricks used for construction.

• Mineral and Industry
• /
• v.29
• /
• pp.56-66
• /
• 2016

In Korea, where hydrothermal alteration zones are widely distributed, clay veins formed by hydrothermal alteration processes on natural slopes or artificial slopes can play an important role in the slope stability. When the surface water infiltrates the ground where the clay vein exists, the pore water pressure in the ground can be locally increased due to impermeable properties of clay minerals. Infiltration of the surface water induces the increase in the pore water pressure, which can cause erosion of the fine clay particles. The eroded clay particles flow and deposit in an area where the flow velocity is slowed down. Where clay minerals are deposited, ground water can leak due to an increase in local pore pressures, which can cause slope failure. In this paper, studies related to hydrothermal clay vein and landslide are introduced.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.10
• /
• pp.199-206
• /
• 2019

This study aims to recycle redmud which is a byproduct in the alumina industry. Redmud ceramics were prepared according to the type of raw materials by blending redmud with the raw materials used in the conventional clay bricks. In this paper, the compressive strength, water absorption ratio, and shrinkage of redmud ceramics prepared by mixing clay bricks were evaluated. Compressive strength and absorption ratio of redmud ceramics were compared with the clay brick criteria of KS L 4201. At the firing temperature of $1200^{\circ}C$, the specimens containing redmud only and the redmud with sandy loam and black clay were found to satisfy the 1st class of clay brick. The quality standard of compressive strength and absorption ratio was obtained by firing redmud with black clay and sandy loam at $1200^{\circ}C$. Also, when the redmud was mixed with black clay and feldspar, the 2nd class was satisfied when the sample was fired at $1100^{\circ}C$.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.53 no.3
• /
• pp.292-296
• /
• 2008

Clay-coated rice seeds (clay-coated seeds A and B) were directly sown on dry paddy and their growth and yield were compared with the normal drill-sown seeds on dry flat paddy. In clay-coated seeds, germination was 1 day earlier and the emergence rate was higher up to 5% than that of normal drill-sown seeds. But the apparent number of seedling stand per $m^2$ was lower than that of normal drill-sown seeds, which is due to the smaller amount of seeding in clay-coated seeds. At the early growth stage, the plant height of clay-coated seeds A was taller than that of drill-sown seeds, while the plant height of clay-coated seeds B was 0.7 cm shorter than that of drill-sown seeds. At the late growth stage, however, the difference was insignificant in both cases. The maximum tillering stage was 10 days earlier in drill-sown seeds. Lodging index was the lowest in clay-coated seeds B and there was no difference between clay-coated seeds A and drill-sown seeds. The ratio of stem base weight, culm diameter and culm wall thickness were higher in clay-coated seeds, while the lower internodes (4th, 5th and 6th) length was shorter in claycoated seeds than in drill-sown seeds. In clay-coated seeds, the number of panicle per $m^2$ was smaller, while the number of spikelet per panicle was a little larger than in drill-sown seeds. The rate of ripened grain and brown rice 1,000 grain weight were lower in the clay-coated seeds, thus the yield was $98{\sim}99%$ level of drill-sown seeds. Considering that the amount of seeding in clay-coated seeds was two-thirds of that in drill-sown seeds, it is expected that clay coating method could become an additional technique for direct seeding cultivation.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.6
• /
• pp.837-843
• /
• 2010

This research investigated classification of clay activity degree by different clay mineral components. Based on compositions of different clay and oxide minerals within 390 soil series in Korea, 7 soils were selected to analyze for CEC and specific surface area of clay minerals. As a result, soils were mainly composed with Chlorite originated from sandstone, Smectite originated from Andesite porphyry and combination of Allophane and Ferrihydrite originated from volcanic ash, if the ratio of CEC value to clay content (degree of clay activity) was greater than 0.7. If the degree of clay activity was ranged between 0.3 and 0.7, soils were composed mainly with Kaolin originated from anorthite. Soils with this ratio also was composted with combinations of Kaolin, Illite and Vermiculite originated with river deposits. When the degree of the activity was less than 0.3, soils were commonly red-yellowish color and composed with two different minerals. One type of composition was Kaolin originated from granite and granite gneiss and the soils contained Geothite and Hematite. The other type was composited mainly with Illite and Vermiculite minerals originated from granite. These soils contained Gibbsite, Geothite and Hematite. The degree of clay activity was highly related with CEC and specific surface area. The greater degree of the activity displayed greater values of clay CEC and specific surface area. It is not easy to measure actual quantity and compositions of clay minerals, while the degree of clay activity can be measured from routine soil analyses. As a conclusion, the degree of clay activity may be not just a simple but also powerful tool to estimate physical-chemical properties of soils and to evaluate the soil classification in Korean soils.

• Geomechanics and Engineering
• /
• v.4 no.4
• /
• pp.281-294
• /
• 2012

Filtration using granular media such as quarried sand, anthracite and granular activated carbon is a well-known technique used in both water and wastewater treatment. A relatively new pre-filtration method called pebble matrix filtration (PMF) technology has been proved effective in treating high turbidity water during heavy rain periods that occur in many parts of the world. Sand and pebbles are the principal filter media used in PMF laboratory and pilot field trials conducted in the UK, Papua New Guinea and Serbia. However during first full-scale trials at a water treatment plant in Sri Lanka in 2008, problems were encountered in sourcing the required uniform size and shape of pebbles due to cost, scarcity and Government regulations on pebble dredging. As an alternative to pebbles, hand-made clay pebbles (balls) were fired in a kiln and their performance evaluated for the sustainability of the PMF system. These clay balls within a filter bed are subjected to stresses due to self-weight and overburden, therefore, it is important that clay balls should be able to withstand these stresses in water saturated conditions. In this paper, experimentally determined physical properties including compression failure load (Uniaxial Compressive Strength) and tensile strength at failure (theoretical) of hand-made clay balls are described. Hand-made clay balls fired between the kiln temperatures of $875^{\circ}C$ to $960^{\circ}C$ gave failure loads of between 3.0 kN and 7.1 kN. In another test when clay balls were fired to $1250^{\circ}C$ the failure load was 35.0 kN compared to natural Scottish cobbles with an average failure load of 29.5 kN. The uniaxial compressive strength of clay balls obtained by experiment has been presented in terms of the tensile yield stress of clay balls. Based on the effective stress principle in soil mechanics, a method for the estimation of maximum theoretical load on clay balls used as filter media is proposed and compared with experimental failure loads.