• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.1
• /
• pp.117-122
• /
• 2016

In this paper, we propose 24-GHz CMOS radio frequency (RF) power amplifier for short-range automotive collision avoidance radars. This circuit contains common source stage with inter-stages conjugate matching circuit as a class-A mode amplifier. The proposed circuit is designed using TSMC $0.13-{\mu}m$ mixed signal/RF CMOS process ($f_T/f_{MAX}=120/140GHz$). It operates at the supply voltage of 2V, and it is designed to have high power gain, low insertion loss and low noise figure in the low supply voltage. To reduce total chip area, the circuit used transmission lines instead of the bulky real inductor. The designed CMOS power amplifier showed the smallest chip size of $0.1mm^2$, the lowest power consumption of 40mW, the highest power gain of 26.5dB, the highest saturated output power of 19.2dBm and the highest maximum power-added efficiency of 17.2% as compared to recently reported results.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.05a
• /
• pp.765-767
• /
• 2014

본 논문에서는 단거리 레이더용 차량 추돌 방지 24-GHz CMOS 고주파 전력 증폭기 (RF Power Amplifier)를 제안한다. 이러한 회로는 class-A 모드 증폭기로서 단간 (inter-stages) 공액 정합 (conjugate matching) 회로를 가진 공통-소스 단으로 구성되어 있다. 칩 면적을 줄이기 위해 실제 인덕터 대신 전송선(Transmission Line)을 이용하였다. 제안한 회로는 TSMC $0.13{\mu}m$ 혼성 신호/고주파 CMOS 공정 ($f_T/f_{MAX}=120/140GHz$)으로 설계하였다. 설계한 CMOS 고주파 전력 증폭기는 최근 발표된 연구결과에 비해 약 22dB의 높은 전력이득 및 7.1%의 높은 PAE 특성을 보였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.813-822
• /
• 2009

We have investigated operation of a 1:2:2 asymmetric 3-stage Doherty PA(Power Amplifier) and implemented using the Freescale's 4 W, 10 W PEP LDMOSFETS at 1 GHz. By employing the three peak efficiency characteristics, compared to the two peak N-way Doherty PA, the asymmetric 3-stage Doherty can overcome the serious efficiency degradation along the backed-off output power region and maximize the average efficiency for the modulation signal. To maximize the efficiency characteristic, the inverse class F PA has been designed as carrier and peaking amplifiers. Furthermore, to extract the proper load modulation operation, the adaptive gate bias control signal has been applied to the two peaking PAs based on the envelope tracking technique. For the 802.16e Mobile WiMAX(World Interoperability for Microwave Access) signal with 8.5 dB PAPR(Peak to Average Power Ratio), the proposed Doherty PA has shown 55.46 % of high efficiency at an average output power of 36.85 dBm while maintaining the -37.23 dB of excellent RCE(Relative Constellation Error) characteristic. This is the first time demonstration of applying the saturated PA and adaptive gate bias control technique to the asymmetric 3-stage Doherty PA for the highly efficient transmitter of the base-station application.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.880-886
• /
• 2007

We have proposed a new "hybrid" envelope elimination and restoration(EER) transmitter architecture using an efficiency optimized power amplifier(PA) and modified bias modulator. The efficiency of the PA at the average drain voltage is very important for the overall transmitter efficiency because the PA operates mostly at the average power region of the modulation signal. Accordingly, the efficiency of the PA has been optimized at the region. Besides, the bias modulator has been accompanied with the emitter follower for the minimization of memory effect. A saturation amplifier, class $F^{-1}$ is built using a 5-W PEP LDMOSFET for forward-link single-carrier wideband code-division multiple-access(WCDMA) at 1-GHz. For the interlock experiment, the bias modulator has been built with the efficiency of 64.16% and peak output voltage of 31.8 V. The transmitter with the proposed PA and bias modulator has been achieved an efficiency of 44.19%, an improvement of 8.11%. Besides, the output power is enhanced to 32.33 dBm due to the class F operation and the PAE is 38.28% with ACLRs of -35.9 dBc at 5-MHz offset. These results show that the proposed architecture is a very good candidate for the linear and efficient high power transmitter.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.2
• /
• pp.56-61
• /
• 2010

In this paper, high efficient power amplifier with dual band has been realized. Dual band power amplifier have used modify stub matching for single FET, center frequency 2.14GHz and 5.2GHz respectively. The dual-band operation of the CRLH TL is achieved by the frequency offset and the nonlinear phase slope of the CRLH TL for the matching network of the power amplifier. Because the control of the all harmonic components is very difficult m dual-band, we have managed only the second- and third-harmonics to obtain the high efficiency with the CRLH TL in dual-band. Dual-band characteristics in the output has to balance. Two operating frequencies are chosen at 2.14 GHz and 5.2 GHz in this work. The measured results show that the output power of 28.56 dBm and 29 dBm was obtained at 2.14 GHz and 5.2 GHz, respectively. At this point, we have obtained the power-added efficiency (PAE) of 65.824 % and 69.86 % at two operation frequencies, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.162-172
• /
• 2011

In this paper, a design and fabrication of 4 W power amplifier for the WiMAX frequency band(2.3~2.7 GHz) are presented. The adopted active device is a commercially available GaN HEMT chip of Triquint Company, which is recently released. The optimum input and output impedances are extracted for power amplifier design using a specially self-designed tuning jig. Using the adopted impedances value, class-F power amplifier was designed based on EM simulation. For integration and matching in the small package module, spiral inductors and interdigital capacitors are used. The fabricated power amplifier with $4.4{\times}4.4\;mm^2$ shows the efficiency above 50 % and harmonic suppression above 40 dBc for second(2nd) and third(3rd) harmonic at the output power of 36 dBm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.11
• /
• pp.1137-1140
• /
• 2011

In this paper, the optimal condition for efficient active frequency multipliers is analyzed. This analysis is based on the effects from transistor nonlinear coefficients, harmonic impedances, and output parasitic components. From the analysis, normalized harmonic power is estimated with the clipping condition of a commercial transistor, and the condition for high conversion efficiency is suggested. From the analysis, a class-F frequency tripler was implemented for the output at 2.475 GHz, showing the maximum efficiency of 22.9 % and the maximum conversion gain of 9.5 dB.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.726-729
• /
• 2013

In this paper, low power and high slew rate CMOS rail to rail input/output opamp applicable for ouput buffer amp, in LCD source driver IC, is proposed. Proposed op-amp, is realized the characteristics of low power consumption and high slew rate adding the newly designed control stage of class-B to the conventional output stage of class-AB. From the simulation results, we know that the proposed opamp buffer can drive a 1000pF capacitive load with a 6.5V/us slew-rate, while drawing only the the power consumption of 1.19mW from 3.3V power supply.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.113-117
• /
• 2003

This paper describes the design and the simulation results of the RF CMOS Class-E Power Amplifier for a 2.4GHz ISM band. This circuit is composed two connected amplifiers. where Class F amplifier drives Class E amplifier. The proposed circuit can reduce the total power dissipation of the driving stage and can work with higher efficiency. The power amplifier has been implemented in a standard $0.25{\mu}m$ CMOS technology and is shown to deliver 100mW output power to load with 41% power added efficiency(PAE) from a 2.5V supply.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.335-339
• /
• 2003

This Paper describes the design and the simulation results of the RF CMOS Class-E Power Amplifier for a 2.4GHz ISM band. This circuit is composed two connected amplifiers. where Class F amplifier drives Class E amplifier. The proposed circuit can reduce the total power dissipation of the driving stage and can work with higher efficiency. The power amplifier has been implemented in a standard 0.25$\mu\textrm{m}$ CMOS technology and is shown to deliver 100mW output Power to load with 41％ power added efficiency(PAE) from a 2.5V supply.