• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.545-548
• /
• 2002

This paper proposes a unidirectional beam antenna using a probe excited circular ring near the reflector. The antenna structure is simple. The radiation characteristics of the antenna fur various spacing between a probe excited circular ring and the reflector are analyzed. These characteristics are also compared with the conventional single aperture near the reflector. It is found that the proposed structure yields better characteristics than the conventional structure. The numerical results of the radiation pattern, elevational beam peak, beamwidth, and maximum directivity are investigated. The result of the analysis is very useful to design the antenna of the high directivity with unidirectional beam.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.7
• /
• pp.25-32
• /
• 2021

In the previous study, a study was conducted to improve the exhaust gas intake efficiency by improving the existing soot measurement probe in the shape and angle of the exhaust port. As a result, it can be seen that the smoke measurement performance according to the shape and angle is improved. In previous studies, the performance of the soot probe was not confirmed for the Korean KD 147 mode, which has a low suction flow rate and a long inspection time. So, we would like to confirm the improvement of the smoke probe performance of the Korean KD 147 mode, which is close to the actual driving conditions. The probe used in this study is another type of probe, and has a circular ring shape instead of a rib and variable center position unit, so the probe center hole is located close to the center of the exhaust pipe.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.2
• /
• pp.24-29
• /
• 2002

A study for the circularity of machine tool is classified into two ways. One is to measure the circularity of machine tool by a existing measuring device. The other is to measure the circularity by remodeling the existing measuring device. We will improve on measurement of circularity using circular test method by a two-dimensional probe and a master ring for machining tools and investigate influence of trigger method, acceleration data sampling.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.54-65
• /
• 1993

The paper describes and alternative method based on a new idea to measure the circular movement of machining centers. ISO has employed three testing methods for the acceptance tests of machine tools; the first is a rotating one-dimensional probe method, the second is a two-dimensional probe and a master circular ring, and the third is a kinematic ball bar. The last two methods were proposed and introduced by W. Knapp and J. B. Bryan, respectively. The newly developed method is superior to above two methods; the rotating angle can be detected and the rotating radius is variable. Circular movement errors of machining centers were investigated by the analysis of data measured by R- .THETA. method. Followint observations are obtained 1) The errors which depend on positions, i.e., periodical errors by the pitch of ball screws, errors by compensation of backlash and errors by perpendicularity of X and Y-axis, were analyzed. 2) The errors which depend on NC control system, i.e., errors by the unbalance of position-loop-gaians, errors by velocity-loop-gains and errors by feed speeds, were quantiatively analyzed. 3) The method of extracting error information, which uses moving technique of averaging angle and fourier's analysis data mesured by the R- .THETA. method, was proposed.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.3
• /
• pp.56-62
• /
• 1996

This paper presented a new measuring system to improve circular motion accuracy by using two-dimensonal probe and master ring for NC machine tools. This measuring system reduced the circular motion error conspicuously by eliminating the influence of the acceleration/deceleration range and compensating the friction force whose influences were significant while measuring the motion. Experimental results show that this system had enough accuracy to measure a circular motion for NC machine tools, compared with the circular test method and the r .theta. method.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.2 no.1
• /
• pp.13-21
• /
• 2003

This paper presents the analysis of the mode characteristics of an annular ring microstrip patch antenna for circular polarization with attachment mode using method of moments in the spectral domain. For a probe excitation, the input impedance are obtained by using the single mode approximation for both the $TM_{11}$ and $TM_{12}$ modes and compared with those by Vector Hankel Transform. While the $TM_{11}$ mode has a high Q, it is a poor radiating mode; the $TM_{12}$ mode is more suitable for antenna applications. It is also shown that the bandwidth of the $TM_{12}$ mode is wider than that of the $TM_{11}$ mode in terms of axial ratio for circular polarizatio

• Electrical & Electronic Materials
• /
• v.11 no.11
• /
• pp.17-21
• /
• 1998

The surface potential distribution on insulating polymers was measured by scanning of the probe of an electrostatic voltmeter. The measurements were done for two measured by scanning of the probe of an electrostatis voltmeter. The measurements were done for two cases. In the first case, it was measured on the free surface of insulating films which had been inserted between plane electodes after the removal of the upper brass disk electrode. In the second case, we measured the charging region between a circular and its opposing concentric ring electrodes after the removal of dc ramp voltage in air and nitrogen gas.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.719-722
• /
• 2002

This paper reports the characteristics of a bidirectional antenna by using a planar array of a probe excited circular ring. The element of a bidirectional antenna is first designed to achieve the maximum directivity. The directivity can be further increased by arranging these elements to form the linear array. There are two types of linear array to be investigated i.e., on axis and off axis arrangement. On-axis linear array yields better directivity than off-axis linear array. Therefore, this orientation is further used to form the planar array. The radiation characteristics of this optimum planar array are rigorously reported. The proposed structure is very useful to extend the distance between the base station in PCT system.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.10
• /
• pp.41-49
• /
• 2013

This paper suggests the dielectric resonator antenna using LTCC process for mm-wave car radar system. In this paper, dielectric resonator antennas (DRA) operated in 76-77 GHz frequency band are designed. And, using the LTCC process, the structures of dielectric resonator with SRR (split ring resonator) inside and those of dielectric resonator with probe inside are suggested. Linear polarization antennas and circular polarization antenna are designed for the DRA with probe inside. Three kinds of the DRA antennas are designed and their characteristics are calculated using CST RF simulation tool. The designed antennas are fabricated and measured and the measured results are compared with calculated results. The measured operating frequencies of DRAs are within 76 GHz to 77 GHz, which are close to the calculated results, and the measured gains are about 8.15 dBi to 10.82 dBi.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.47 no.5
• /
• pp.52-61
• /
• 2010

The use of the friction coefficient is known to provide good discrimination ability in the classification of human constitutions, which are used in alternative medicine. In this study, a system that uses a multi-axis load cell and a hemi-circular probe is designed. The equipment consists of a sensor (load cell type, manufactured by the authors), an x-axis linear-bush guide motorized mobile stage that supports the hand being analyzed, and a signal conditioner. Using the proposed system, the friction coefficients from different constitutions were compared, and the relative repeatability error for the friction coefficient measurement was determined to be less than 2 %. The direction along the ring finger line was determined to be the optimum measurement region for a constitutional diagnosis between Tae-eumin and Soyangin types using the proposed system. There were some differences in the friction coefficient between the two constitutions, as reported in ancient literature. The proposed system is applicable to a quantitative constitutional diagnosis between Tae-eumin and Soyangin types within an acceptable level of uncertainty.