• 한국전산유체공학회:학술대회논문집
• /
• 1997.10a
• /
• pp.136-142
• /
• 1997

The present study is aimed to investigate flow characteristics of confined jet flow within circular pipe. Numerical method based upon revised SOLA scheme which secures conservation form of convective terms on irregular grids by interpolating the variables appearing in staggered meshes is adopted on cylindrical coordinate formation. Computation was carried out for two kinds of Reynolds number, $10^5\;and\;1.5{\times}10^5$ defined by diameter of outer pipe and time-mean driving jet velocity. Results show that periodic vortex shedding from the jet mixing layer is profound and related unsteady flow characteristics prevail over the entire region. Spatial distribution of pressure and kinetic energy, fluctuation of static wall pressure, together with radial velocity components are examined in terms of instantaneous and time-mean point of views.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3335-3344
• /
• 1994

The initial flow characteristics of the turbulent circular jet discharging into the sudden expansion pipes have been investigated by the hot wire anemometry. Evolutions of similarity, centerline behavior, jet boundary and typical turbulent quantities were looked into for the expansion ratios. The results show that the spreading rates of discharging jet seem not to be dependent of the expansion ratio and that the velocity profiles in the radial directions exhibit the similarity in the regions, 2-5d, 2-6d and 3-8d for the corresponding expansion rations of 2, 3 and 5, respectively. With the increase of expansion ratio the centerline velocity decays rather slowly. The anisotropic behaviors of the discharging jets into the sudden expansion pipe look stronger than those of the free jet.

• Journal of the Korea Society for Simulation
• /
• v.14 no.4
• /
• pp.69-76
• /
• 2005

To investigate the characteristics of the sound-pipe on the top of King Song-Dok bell, using computer simulation, the throat impedance was evaluated for the straight pipe and conical pipes with varying taper angles. When sound propagates in a rigid walled, unflanged circular pipe with wavelength larger than radius, the acoustic motion is planar, much as in a bar. The incident sound waves are reflected at the end of pipe and some of them are transmitted. The reflection coefficient and radiation impedance of the sound-pipe of King Song-Dok bell were calculated, and the results demonstrated that the high frequency sound is radiated through the sound-pipe. It behaves like a frequency filter.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.1139-1140
• /
• 2013

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.509-510
• /
• 2009

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.5 s.248
• /
• pp.533-542
• /
• 2006

In order to assess the integrity of pipes with local thinning area, the plastic strain as well as the elastic strain at the root of thinned region are required particularly when fluctuating load is applied to the pipe. For estimating elastic-plastic strain at local wall thinning area in a straight pipe under tensile load, an estimation model with idealized fully circumferential constant depth wall thinning area is proposed. Based on the compatibility and equilibrium equations a nonlinear estimation equation, from which local elastic-plastic strain can be determined as a function of pipe/defect geometry, material and the applied strain was derived. Estimation results are compared with those from detailed elastic-plastic finite element analysis, which shows good agreements. Noting that practical wall thinning in nuclear piping has not only a circular shape but also a finite circumferential length, the proposed solution for the ideal geometry is extended based on two-dimensional and three-dimensional numerical analysis of pipes with circular wall thinning.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.5
• /
• pp.552-557
• /
• 2007

This paper has dealt with the effect of non ionized surfactant and water mixture on drag reduction and heat transfer enhancement in a circular pipe flow with experimentally. The test section was consisted of stainless steel pipe with inside diameter of 16mm. The wire coil was used to increase heat transfer in a pipe and the on ionized surfactant(Oleyl Dihydroxyethyl Amino Oxide, ODEAO) was used to reduce the drag force of water mixture with surfactant. The main parameters of this experiment were diameter and pitch of wire coil and the ratio of test section length and horizontal wire coil length. In this experiment, the acquired results were 1) Drag reduction effect existed in this ODEAO-water mixture, 2) Friction factor and heat transfer were increased with insertion the heat transfer enhancement coil, 3) With increasing of pitch ratio, heat transfer was decreased, and 4) Heat transfer was decreased by the decreasing of inserting coil diameter.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1630-1633
• /
• 2003

Hair pin bending machine is pipe forming machine consisting of heat exchanger product system. Hair pin produced by these machine is pathway of refrigerant and play a important role improving the performance and productivity of heat exchanger. The core technology of hair pin bending machine is forming the straight pipe into U-type without any defaults. Therefore, this paper study the relation between the pipe bending forming and the shape and position of mandrel using the elastic-plastic finite element analysis and provide a foundation technology for which developing the hair pin bending machine. The results are followed 1. Mandrel located in front of rotating center of bending die minimized the circular shape variation of copper pipe. 2. Diameter change of mandrel hardly effect the pipe shape.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.10a
• /
• pp.256-260
• /
• 1993

The circular pipe was developed using polymer mortar. Pipe (inside diameter=170 mm and length=1,000 mm was made to evaluate structural performance. The average failure load for the pipes which were reduced its thickness by 41% was 2,000 kg which was higher than that of conventional concrete pipe of the same size. Reinforcement using glass fiber fabric highly increased the failure load, up to 9,500 kg.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3098-3103
• /
• 2007

In this paper, natural convection of a magnetic fluids(W-40) in a half circular pipe enclosure are investigated by numerical and experimental method. One side wall is kept at a constant temperature(25$^{\circ}C$), and the opposite side wall is also kept at a constant temperature(20$^{\circ}C$). Under above conditions, various magnitudes of the magnetic fields were applied up. Theoretical study through the governing equation derived by Siliomis is carried out with numerical analysis by the GSMAC Method. And the thermo-sensitive liquid crystal film(R20C5A) is utilized in order to visualize wall-temperature distributions as an experimental method. This study has resulted in the following fact that the natural convection of a magnetic fluids are controlled by the direction and intensity of the magnetic fields.