• 대한기계학회논문집
• /
• 제18권6호
• /
• pp.1551-1558
• /
• 1994

An experiment was conducted to investigate whether an equation of heat transfer coefficient derived form energy equation of two-phase plug flow can be actually applied to the industrial field. The heat is constantly transfered to the sand beds from the wall of heat exchanger while the sand moves down through cylindrical heat exchanger by gravity from feed hooper. To increase heat transfer, turbulators such as glass ball and steel pipe packings were used. In addition, the experiment in the case of fluidizing the sand beds was also carried out. The temperatures of the sand beds and the wall were measured along the heat exchanger axis. The density and porosity of the sand beds were also measured. The deviations of the mean velocity of sands from the velocity on the wall surface because of the slip conditions on the wall were negligible (within 3%). The heat transfer coefficients when the turbulators were used and when the sand beds were fluidized were found to be much greater than those of the plain plug flow.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권1호
• /
• pp.169-174
• /
• 2008

Floating devices, such as a cavity resonance device take advantage of both the water motion and the wave induced motions of the floating body itself. The wave energy converter is known commercially as the WAGB(Wave Activated Generator Buoy) and is used in some commercially available buoys to power navigation aids such as lights and horns. This wave energy converter consists of a circular floatation body which contains a vertical center pipe that has free communication with the sea. A theoretical analysis of this power generated by a pneumatic type wave energy converter is performed and the results obtained from the analysis are used for a real wave energy converter for buoy. This paper presents the analysis results and the design method for the WEC(Wave Energy Converter), and the associate results are application to the commercially available WEC for buoy. Maximum performance of WEC occurs at resonance with driving waves. The analysis of WEC is performed with LabVIEW program, and the design method of WEC for buoy is suggested in this paper.

• Nuclear Engineering and Technology
• /
• 제47권4호
• /
• pp.389-397
• /
• 2015

The effects of mixing vanes (MVs) attached to a grid spacer on the characteristics of air-water annular flows were experimentally investigated. To know the effects, a grid spacer with or without MV was inserted in a vertical circular pipe of 16-mm internal diameter. For three cases (i.e., no spacer, spacer without MV, and spacer with MV), the liquid film thickness, liquid entrainment fraction, and deposition rate were measured by the constant current method, single liquid film extraction method, and double liquid film extraction method, respectively. The MVs significantly promote the re-deposition of liquid droplets in the gas core flow into the liquid film on the channel walls. The deposition mass transfer coefficient is three times higher for the spacer with MV than for the spacer without MV, even for cases 0.3-m downstream from the spacer. The liquid film thickness becomes thicker upstream and downstream for the spacer with MV, compared with the thickness for the spacer without MV and for the case with no spacer.

• 동력기계공학회지
• /
• 제17권2호
• /
• pp.56-62
• /
• 2013

A technique is presented that uses a circular waveguide for the measurement of the bulk shear (S-wave) velocities of unconsolidated, saturated media, with particular application to near surface soils. The technique requires the measurement of the attenuation characteristics of the fundamental torsional mode that propagate along an embedded pipe, from which the acoustic properties of the surrounding medium are inferred. From the dispersion curve analysis, the feasibility of using fundamental torsional mode which is non-dispersive and have constant attenuation over all frequency range is discussed. The principles behind the technique are discussed and the results of an experimental laboratory validation are presented. The experimental data are best fitted for the different depths of wetted sand and the shear velocities are evaluated as a function of depths. Also the characteristics of the reflected signal from the defects are examined and the reflection coefficients are calculated for identifying the relation between defect sizes and the magnitude of the reflected signal.

• Tribology and Lubricants
• /
• 제10권4호
• /
• pp.43-50
• /
• 1994

In order to elucidate the effects of co-existing additives (S$_{8}$, TBP: Tri butyl phosphate, ZnDTP: Zinc-dialkyl dithiophosphate) and the role of reacted surface film on the friction behavior of MoDTP (molybdenum dialkyl dithiophosphate), a friction experiment using a dual circular pipe edge surface type friction tester and XPS (X-ray photoelectronic spectrum) surface analysis were conducted. Friction reduction with MoDTP lubricant was proved to be greatly influenced by co-existing additive species. It was dependent on the properties of the film formed through the reaction between the additive and the surface. Phosphate film reduced the friction coefficient of MoDTP through suppression of diffusion of Mo compounds towards the metal substrate. On the other hand, sulfate film, which is inherently rich in lattice defects, did not lead to any appreciable friction reduction with MoDTP since the diffusion of the Mo compound towards the metal substrate was not effectively suppressed. With ZnDTP additive, the sulfide film formed through decomposition greatly influenced the lubricating performance of MoDTP. As such, properties of surface films formed from additives were proved to yield significant influence on the lubrication performance of MoDTP.

• 대한기계학회논문집A
• /
• 제29권6호
• /
• pp.904-912
• /
• 2005

The flow in a microchannel is usually characterized as a low Reynolds number (Re) so that good mixing is quite difficult to be achieved. In this regard, we developed a novel chaotic micromixer, named Barrier Embedded Kenics Micromixer (BEKM). In the BEKM, the higher level of chaotic mixing can be achieved by combining two general chaotic mixing mechanisms: (i) splitting/reorientation by helical elements inside the microchannel and (ii) stretching/folding via periodically located barriers on the channel wall. The fully three-dimensional geometry of BEKM was realized by a micro-stereolithography technology, in this study, along with a Kenics micromixer and a circular T-pipe. Mixing performances of three micromixers were experimentally characterized in terms of an average mixing color intensity of phenolphthalein. Experimental results show that BEKM has better mixing performance than other two micromixers. Chaotic mixing mechanism, proposed in this study, could be integrated as a mixing component with Micro-Total-Analysis-System, Lab-on-a-chip and so on.

• 대한기계학회논문집B
• /
• 제24권8호
• /
• pp.1104-1111
• /
• 2000

Erosion-corrosion in a pipe system often occurs at fittings, valves, and weld beads where flow separation and reattachment yield high turbulence intensity. Thus identifying their correlations would be the first step towards resolving the erosion-corrosion problems associated with industrial applications. Bremhorst of the Univ. of Queensland, Australia, proposed that a rotating cylinder with surface roughness (two backward-facing steps periodically mounted on a circular cylinder) be an economical and tractable tool which can generate extreme flow conditions for erosion-corrosion study. In this work, DNS has been carried out for turbulent flows around the same rotating cylinder as his experimental apparatus. Our result shows that a region of intense turbulence intensity and high wall-shear stress fluctuation is formed along the cylinder surface in the recirculating region behind the step, where high mass-transfer capacity is also experimentally observed. Since corrosion is mass-transfer controlled, our finding sheds light on the direction of future corrosion research.

• 물과 미래
• /
• 제23권2호
• /
• pp.251-263
• /
• 1990

본 연구의 목적은 도시 유역에서의 표면유출에 의한 맨홀 유입량을 추정하고 관망에서의 흐름을 해석하기 위한 모형을 개발하기 위한 것이다. 각 맨홀로의 유입량은 합리식을 이용한 단순방법으로 유입 수문곡선을 모의하는 방법과 해당유역 특성을 고려한 표면유출 모의에 의한 유입 수물곡선 결정방법이 이용된다. 관망에서의 흐름은 Saint-Venant공식의 dynamic equation에 유한음차분법(four-point implicit method)응 적용하여 동시해법으로 해석하였다. 특히 압력류(surcharge flow)흐름은 관의 상단에 좁고 긴 가상관을 연결시켜 모든 흐름을 개수로 흐름으로 해석가능 하도록 전환함으로써 해석의 단순화를 기하였고, 개발된 USS-slot모형이 부정류 우수관망 흐름을 적절히 모의할 수 있는가를 판별하기 위하여 기존에 연구된 관망에 적용하여 그 결과들을 비교 분석하였다.

• 동력기계공학회지
• /
• 제11권4호
• /
• pp.44-49
• /
• 2007

Generally, the economic concept of optimized design and operating conditions in fluidized bed heat exchangers can hardly be realized. Because the lack of fundamental knowledge about the particle flows, the optimum design of the fluidized bed heat exchanger is rather limited. In the present work, measurements are made on pressure drops and friction factors in the horizontal circular tube with solid particles in the circulating water. Two different solid particles of diameters of 3mm and 4mm are covered. The Reynolds numbers are ranged from 10,000 to 45,000. It is concluded that the friction factors for the particles of 4mm diameter are much higher than those for the particles of 3mm diameter. And at the lower particle concentration, the friction factors are strongly influenced by the fluid velocity rather than the particle concentration; However, the effect of the particle concentration on friction factors is also significantly higher at a higher particle concentration operating condition.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.760-767
• /
• 2014

This paper proposes a method to calculate pressure and flow of the fluid dynamic bearings (FDBs) with a recirculation channel (RC) by solving the Reynolds and the Hagen-Poiseuille equations at the same time. The Hagen-Poiseuille equation is one-dimensional equation which describes the flow in a circular pipe such as the RC. This research developed a finite element program to solve the Reynolds and the Hagen-Poiseuille equation together. The proposed method was applied to calculate the pressure and flow of the FDBs which are composed of grooved or plain journal and thrust bearings, and RC. To verify the proposed method, it also developed a finite volume model of the FDBs, and pressure and flow were calculated by the commercial CFD solver. They agree well with the pressure and flow calculated by the proposed method. Finally, this research investigated the characteristics of the FDBs due to the radius change of the RC.