• 한국군사과학기술학회지
• /
• 제25권5호
• /
• pp.545-551
• /
• 2022

We proposed a design method for constant current pyro squib circuit. The current method using N MOSFET for the stability problem has a weakness of the current change, requiring a new design. This paper identified the problem with conventional squib circuit where the current is reduced by 25 % when maximum resistance is 3 ohms. Thus, we proposed a stable constant current driving circuit using P MOSFET and PNP BJT. We confirmed stable constant circuit operation through simulations and measurements of the proposed circuit design where the current did not change until the resistance reached 3 ohms.

• 한국전기전자재료학회논문지
• /
• 제25권1호
• /
• pp.53-57
• /
• 2012

In this paper, by designing 20 W class driving circuit for driving high-power LED (Light Emitting Diode), we are going to comparatively carry out the analysis of characteristics for power circuit according to each design method. In this case, 200 V 60 Hz was performed as input data. The electrical characteristics such as voltage, current and ripple are checked for constant current circuit and constant voltage circuit in the LED module. In addition, as the ripple has an influence on illumination of LED light, low temperature working (-20 [$^{\circ}C$]) and high temperature working(80 [$^{\circ}C$]) are measured to make sure the ripple characteristics in accordance with temperature. In low temperature operation -20 [$^{\circ}C$] measurements, both constant current circuit and constant-voltage circuit were less impacted on input fluctuation, whereas in the high temperature operation 80 [$^{\circ}C$], current voltage in constant voltage circuit was surge after 430 [hour]. Voltage current ripple of constant current circuit was much less than constant voltage circuit, therefore we can show that constant current circuit is more stable.

• 전기학회논문지
• /
• 제56권7호
• /
• pp.1261-1267
• /
• 2007

Although LEDs have been used in various applications with improving the brightness and luminous efficacy, the electrical and optical characteristics of high power LED varies at different temperature and starting time. In this paper, optimal heat sink and apparatus design were conducted using IR camera and ICEPAK on the LED bulb consisting with fourteen LED array. The temperatures of heat sink and LED device of the designed LED bulb without cooling pan were $74^{\circ}C\;and\;96.8^{\circ}C$, respectively, showing in good themal characteristics. For high efficiency driving circuit of LED array adopted optimal heat sink design, driving circuits of constant voltage and current circuits were suggested and fabricated. As a result the efficacy of all driving circuits showed more than 20 lm/W. Also, the constant current circuits are suitable for signal lamp, hallway lamp, and flash lamp having short operating time(about 30 min). On the other hand, a reading light and indoor lamp having long operating time can be controlled by constant voltage circuit.

• 한국산업정보학회논문지
• /
• 제28권2호
• /
• pp.21-30
• /
• 2023

전기차 보급과 고성능화가 진행됨에 따라 높은 출력을 가지는 모터의 수요가 증가하고 고용량 IPMSM 생산을 위한 고용량 착자기의 중요성 또한 증가하고 있다. 착자에 중요한 착자 전류의 최댓값과 커패시터 방전시간은 착자요크의 회로정수에 의해 결정된다. 본 논문에서는 착자기 설계를 위한 착자요크의 회로정수 설계를 위하여 MATLAB SIMULINK를 활용한 착자 시스템의 해석을 진행하고 회로정수 설계를 위한 설계 절차를 제시한다. 그 결과 착자용량 5,000[V], 15,000[uF]에 따라 착자요크 파라미터는 0.015[ohm], 0.035[mH]로 도출하였다.

• 한국산업정보학회논문지
• /
• 제6권2호
• /
• pp.74-79
• /
• 2001

로봇과 자동화기기에 범용으로 사용되는 Stewing Motor의 Driving을 위하여 unipolar 방식과 bipolar 방식의 Controller Circuit를 design 하였으며 특히 design시 Digital logic을 이용하여 Controller를 설계 제작하여 실험을 통해 그 응용성을 실험하였다. 또한 Motor의 효율 향상을 위하여 Motor의 Winding에 흐르는 전류를 제어하기 위하여 constant Current Limit Methode와 Constant Voltage Limit Methode를 분석하고 실재 회로 제작 시 응용하여 Motor의 효율을 향상시켰다.

• 한국정보전자통신기술학회논문지
• /
• 제11권5호
• /
• pp.586-592
• /
• 2018

본 논문은 140W 급 저면적 LED 전원 제어 회로 설계를 위해 다양한 기능이 집적된 HIC를 제안한다. 제안된 HIC는 정전압/정전류 구동회로, 단락 보호회로, 내부 정전압회로, dimmer 회로를 하나로 집적해, 제작 시 기존 시스템 대비 PCB 가로 길이를 16% 절감하는 효과를 보였다. 다양한 실험을 통해 HIC 내부에 설계된 각 블록의 성능을 검증했고, (정전압 구동회로 변동률 2.9%, dimmer 회로 오차 5%이내, 720 mA에서 안정적인 short protection) 제안된 HIC를 적용해 시스템에서 필요로 하는 전력 대비 PCB 면적을 상당히 줄일 수 있기 때문에, 제작 시간의 대부분을 차지하는 PCB 제조시간을 단출할 수 있는 효과와 전원 제어 회로에서 발생하는 불량에 대해 기존과 같이 PCB 전체를 교체하지 않고 HIC만 교체할 수 있도록 하여 유지/보수를 쉽게 할 수 있는 효과를 기대한다.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제12권4호
• /
• pp.184-191
• /
• 2004

In order to improve the performance of a 2 room heat pump with a constant speed compressor, the optimum refrigeration circuit of the heat pump with different cooling and heating capacities is developed by applying capillary tubes. The refrigeration circuit is composed of four parts; a heating circuit, a cooling circuit, a by-pass circuit and a balance circuit. The performance of the 2 room heat pump are investigated from a rating experiment and a reliability experiment, using the calorimeter. Results of the rating experiment show that the capacity of heat pump is about $93\%$ of the design value. In particular, the capacity of the cooling single operation is about $13\%$ higher than the design value, and the capacity of the heating multi operation is about $5\%$ higher than the design value. From the reliability experi-ment, it is found that the lowest driving voltage of the compressor is about $75\%$ of the rating voltage. Also the compressor is reoperated normally under the flood back and the over load.

• 조명전기설비학회논문지
• /
• 제25권9호
• /
• pp.8-13
• /
• 2011

In this paper, a mathematical model of the power LED system including the drive circuit will be presented to control the power LEDs current. Using this mathematical model, the constant current adaptive controller will be designed. A constant current drive circuit for power LEDs will be configured using Buck-type converter. Precise constant current controller design is enabled by presenting the mathematical model of power LEDs including the current driving circuits. Using the mathematical model of power LEDs and its drive circuits, the constant current adaptive controller will be designed to obtain the robustness for the parameter uncertainties. In order to verify the validity of the proposed controller, computer simulations are performed.

• International Journal of Precision Engineering and Manufacturing
• /
• 제5권4호
• /
• pp.43-49
• /
• 2004

A spring-actuated linkage system is used to satisfy the desired opening and closing characteristics of the electric contacts of a vacuum circuit breaker. If the type of a circuit breaker and the structure of the linkage system are predetermined, then design parameters such as stiffness, free length and attachment points of the spring become the important issues. In this paper, based on the energy conservation, the total system energy is constant throughout the operating range of the mechanism; a systematic procedure to optimize the spring design parameters is developed and applied to a simplified mechanism of a circuit breaker. The developed procedure is converted to the environment of the multi-body dynamics program, ADAMS for an in-depth consideration of the complex dynamics of a circuit breaker mechanism.

• 한국정밀공학회지
• /
• 제21권3호
• /
• pp.132-138
• /
• 2004

In a vacuum circuit breaker mechanism, a spring-actuated linkage system is used to satisfy the desired opening and closing characteristics of electric contacts. If the type and structure of the linkage system required to the circuit breaker is predetermined, the stiffness, free length and attachment points of a spring become the important design parameters. In this paper, based on the energy conservation that the total system energy is constant throughout the operating range of the mechanism, a systematic procedure for optimizing the spring design parameters is developed and applied to the simplified mechanism of a circuit breaker. Then, in order to consider the complex dynamics of the circuit breaker mechanism rather well, the developed procedure is converted to the environment of a multi-body dynamics program ADAMS.