• 한국철도학회논문집
• /
• 제7권1호
• /
• pp.65-69
• /
• 2004

In reference to this study, Part Ⅰ showed how the system respond to the harmonics originated from electric locomotives. That is, the system response to the harmonics was derived by computational algorithm with numerical formulas in theoretical aspects. However, Real catenary system has complex configuration of conductors and it is an important point that if we can consider the circuit element of catenary conductors as an uniformly distributed RLC element. Moreover, harmonic characteristics in electric locomotive depend on its operational modes. From these point of view, measurements of harmonics are performed for real railway power supply systems under the various operational modes, and spectrum and distortion analyses in measurement data are described.

• 한국정보처리학회논문지
• /
• 제4권1호
• /
• pp.137-148
• /
• 1997

고장진단 문제는 지식기반 시스템를 이용해 해결하려는 시도가 많이 있어왔다. 그러나 대부분의 방식은 휴리스틱 또는 모델기반 방식으로 단일 오류에 대한 문제에 많은 노력이 이루어져 왔다. 단일 오류에 대한 고장진단문제 해결방식을 다중 오류진 단으로 확대할 때 발생하는 지수적인 계산비용은 피할 수 없는 문제점으로 지적되어 왔다. 이 논문에서는 시스템 구성에 따라 블록으로 구분하면 전체 탐색 영역을 국소 화할 수 있다는 점에 착안하여 다중 오류 진단을 위한 효율적인 알고리즘을 제안한 다. 이 알고리즘의 기본 원리는 오류진단을 위한 출력값 측정 지점에 따라 전체 회로 를 블록으로 나누고 다중오류에 대한 발생원인의 지수적 증가를 줄임으로 효율화 시 킬 수 있다. 각각의 블럭으로부터 발생하는 오류에 대해 결합하는 규칙을 개발하고 이를 통해 상호 논리적인 모순이 없는 최소 오류원인 집합을 구한다.

• 대한전자공학회논문지
• /
• 제22권6호
• /
• pp.114-123
• /
• 1985

이 논문은 packet switching 방식에 의한 공중 computer 통신망 개발에 관한 4편의 논문중 제 2부의 논문으로 제 1부의 KORNET의 개요 및 netwo.k managementcenter (NMC)개발에관한 논문에 이어 KO-RNET의 설계와 networhnode Processor(NNP)의 개발에 대해 기술한다. KORNET은 3개의 NNP와 하나의 NMC 로 일차 구성하였는데, NNP는 MC68000 microprocessor를 이용한 multiprocessor system으로 구현되었고, HMC는 중형 computer인 Mv/8000 system을 사용하여 개발하였다. KORNET에서의 packet service 방식은 virtual circuit(VC) 방식으로 하고 routing은 node나 선로의 상태변화에 쉽게 대처할 수 있는 분산적응방식(distributed adaptive routinB)을 사용하였다. 또한, buffo. management는 dy-namic sharing 방식을 채택하여 storage의 사용에 대한 효율성을 높였다. NNP system의 hardware는 modularity를 고려하여 확장이 용이하게 하였으며, software는 CCITT 권고사항 X.25, X.3, X.28, X.29등을 따라 구현하였다.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• 제5권3호
• /
• pp.206-215
• /
• 2005

In this paper, we propose a new design method of Genetic Algorithm Processor(GAP) and Evolvable Hardware(EHW). All sorts of creature evolve its structure or shape in order to adapt itself to environments. Evolutionary Computation based on the process of natural selection not only searches the quasi-optimal solution through the evolution process, but also changes the structure to get best results. On the other hand, Genetic Algorithm(GA) is good fur finding solutions of complex optimization problems. However, it has a major drawback, which is its slow execution speed when is implemented in software of a conventional computer. Parallel processing has been one approach to overcome the speed problem of GA. In a point of view of GA, long bit string length caused the system of GA to spend much time that clear up the problem. Evolvable Hardware refers to the automation of electronic circuit design through artificial evolution, and is currently increased with the interested topic in a research domain and an engineering methodology. The studies of EHW generally use the XC6200 of Xilinx. The structure of XC6200 can configure with gate unit. Each unit has connected up, down, right and left cell. But the products can't use because had sterilized. So this paper uses Vertex-E (XCV2000E). The cell of FPGA is made up of Configuration Logic Block (CLB) and can't reconfigure with gate unit. This paper uses Vertex-E is composed of the component as cell of XC6200 cell in VertexE

• 한국항공우주학회지
• /
• 제35권11호
• /
• pp.1036-1042
• /
• 2007

비행조종컴퓨터 하드웨어 개발은 상용 툴 및 전용 개발치구가 전무하여 전 근대적인 방법으로 개발하고 있어 개발 기간을 단축하기가 용이하지 않다. 모델링 및 시뮬레이션과 가상현실 기술을 이용하여 비행조종컴퓨터 하드웨어 개발에 적용하는 프로세스 개선 툴이 필요하게 되었다. 본 논문에서는 비행조종컴퓨터 입/출력 신호 흐름, 입력 신호의 고장모니터 및 고장 관리 알고리즘, 논리 회로의 작동, 회로기판 조립체의 형상 및 장착 등과 같은 비행조종컴퓨터의 설계특성을 가상의 공간에 시각화 하고 모사할 수 있는 프로세스 개선 툴을 제안한다. 프로세스 개선 툴 사용자는 open flight format의 3차원 모델링 데이터를 이용하여 구성된 비행조종컴퓨터 모델을 사용하여 회로기판 조립체까지 분해/조립을 할 수 있으며 다양한 비행조종컴퓨터 설계 형상을 시뮬레이션 할 수 있다.

• 방사선산업학회지
• /
• 제6권3호
• /
• pp.231-237
• /
• 2012

This paper introduces a gamma-ray measurement system for a transportable tomography which is applicable for an industrial process diagnosis. The gamma-ray measurement system consists of pulse mode operating 72 channel CsI detectors, main AMP-pulse shaper, single channel analyzer, counter and control PC. The CsI crystal is coupled with a PIN diode which is connected to an amplifier and pulse shaper. For a compact design, the amplifier and pulse shaping circuit are included in a single package. 36 sets of CsI detectors are connected to a multi-channel counter through single channel analyzers. A computer controls and collects data from two multi-channel counters. This configuration results in 72 channel counting system in total. The CT rotator and radiation measurement system are controlled by a PC with LabVIEW program. Tomographic data were measured for a phantom by the measurement system and transportable gamma-ray CT. From the experimental data image reconstructions were performed by ML-EM algorithm. The result showed that the CsI detector system can be a suitable component for transportable gamma-ray CT system.

• 전력전자학회논문지
• /
• 제26권6호
• /
• pp.381-389
• /
• 2021

Most diagnosis approaches rely on historical failure data that might not be feasible in real operating conditions because the battery voltage and internal parameters are nonlinear according to various operating conditions, such as cell-to-cell configuration and initial condition. To overcome this issue, the estimator and the predictor require integrated approaches that consider comprehensive data, with the degradation process and measured data taken into account. In this paper, vector autoregressive models (VAR) with various parameters that affect overdischarge to the cell in the battery pack were constructed, and the cell-to-cell parameters were identified using an adaptive model to analyze the influence of failure prognosis. The theoretical analysis is validated using experimental results in terms of the feasibility and advantages of fault prognosis.

• Journal of information and communication convergence engineering
• /
• 제22권1호
• /
• pp.14-22
• /
• 2024

This study presents the design of a Wilkinson power divider for three-way output ports (WPD3OP), which incorporates a defected ground structure (DGS). An asymmetric power divider is integrated into the output ports of the conventional Wilkinson power divider (WPD), establishing a three-way output port configuration. The DGS introduces periodic or irregular patterns into the ground plane to suppress unwanted electromagnetic wave propagation, and its incorporation can enhance the performance of the power divider, in terms of the power-division ratio, isolation, and bandwidth, by reducing spurious resonances. The proposed design algorithm for an asymmetric power divider for three-way output ports is analyzed via circuit simulations using High-Frequency Simulation Software (HFSS). The results verify the validity of the proposed method. The analysis of the WPD3OP integrated with DGS certifies the achievement of a center frequency of 2 GHz. This confirmation is supported by schematic ideal design simulation results and measurements encompassing insertion losses, return losses, and isolation.

• 전기전자학회논문지
• /
• 제16권3호
• /
• pp.235-243
• /
• 2012

In this study, we developed two legged multi-joint robot by using wireless servo motor that was applied by wireless sensor network technology, which is widely used recently, and performed an experiment of walking method of two legged multi-joint robot. We constructed the star network with servo motors which were used at each joint of two-legged robot. And we designed the robot for operation by transmission of joint control signal from main control system or by transmission of the status of each joint to the main control system, so it operates with continuously checking the status of joints at same time. We developed the humanoid robot by using wireless digital servo motor which is different from existing servo motor control system, and controlled it by transmitting the information of angles and speeds of robot joints to the motor(node) as a feedback through main control system after connecting power and setting up the IDs to each joint. We solved noisy problem generated from wire and wire length to connection point of the control device by construction of the wireless network instead of using existing control method of wiring, and also solved problem of poor real time response to gait motion by controlling the position with continuous transmission of control signals to each joint. And we found that the effective control of robot is able by performing the simulation on walking motion in advance with the developed control algorithm which was downloaded into installed memory. Also we performed the stable walking with two-legged robot by attaching pressure sensor to robot sole. And we examined the robot gait operated by application of calculated algorithm on robot movement to each joint. In this study, we studied the method of controlling robot gait motion by using wireless servo motors and measured the torque applied to each joint, and found that the developed wireless servo motor by ZigBee sensor network offers easier control of two legged robot gait and better circuit configuration of it than the existing wired control system could do.

• Journal of Electrical Engineering and Technology
• /
• 제3권3호
• /
• pp.391-400
• /
• 2008

Multi-pulse topology of converters using elementary six-pulse GTO - VSC (gate turn off based voltage source converter) operated under fundamental frequency switching (FFS) control is widely adopted in high power rating static synchronous compensators (STATCOM). Practically, a 48-pulse ($6{\times}8$ pulse) configuration is used with the phase angle control algorithm employing proportional and integral (PI) control methodology. These kinds of controllers, for example the ${\pm}80MVAR$ compensator at Inuyama switching station, KEPCO, Japan, employs two stages of magnetics viz. intermediate transformers (as many as VSCs) and a main coupling transformer to minimize harmonics distortion in the line and to achieve a desired operational efficiency. The magnetic circuit needs altogether nine transformers of which eight are phase shifting transformers (PST) used in the intermediate stage, each rating equal to or more than one eighth of the compensator rating, and the other one is the main coupling transformer having a power rating equal to that of the compensator. In this paper, a two-level 48-pulse ${\pm}100MVAR$ STATCOM is proposed where eight, six-pulse GTO-VSC are employed and magnetics is simplified to single-stage using four transformers of which three are PSTs and the other is a normal transformer. Thus, it reduces the magnetics to half of the value needed in the commercially available compensator. By adopting the simple PI-controllers, the model is simulated in a MATLAB environment by SimPowerSystems toolbox for voltage regulation in the transmission system. The simulation results show that the THD levels in line voltage and current are well below the limiting values specified in the IEEE Std 519-1992 for harmonic control in electrical power systems. The controller performance is observed reasonably well during capacitive and inductive modes of operation.