• Journal of Bio-Environment Control
• /
• v.10 no.2
• /
• pp.88-94
• /
• 2001

Physical and chemical properties, the salt accumulation and leaching of salt by water of coal fly ash ball (ash ball) were evaluated in comparison with perlite and granule rockwool (rockwool). Bulk density, particle density, solid phase, and porosity of ash ball were 0.93 g.cm$^{-3}$ , 2.29 g.cm$^{-3}$ , 40.6%, 59.4%, respectively. The bulk density of ash ball was greater, while porosity was smaller, than that of perlite and rockwool. Saturation moisture capacity was 52% in ash ball, 71% in perlite, and 90% in rockwool. Water contents after drainage for 1 hr of ash ball, perlite, and rockwool were 21%, 27%, and 80%, respectively. Water content of small granules (3-5 mm) of ash ball was 5% greater than that of large (7-15 mm) grannules. The ash ball was a weak alkali substrate with pH 7.6, but not electric conductivity (EC), of the nutrient solution supplied to ash ball slightly increased. When the absorption of mineral ions to substrates were analyzed, ash ball and RW absorbed mainly PO￣$_4$. On tomato culture, salt accumulation in ash ball substrate was similar to that in perlite. Most of the salts in the ash balls were removed by submerging the substrate eight times in distilled water. It is concluded that water holding capacity of ash ball substrate was lo as compared to other substrates, but air permeability, and water diffusion was excellent, making control of medium water content easy.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.10
• /
• pp.957-964
• /
• 2010

The deactivated catalyzed diesel particulate filter-trap (DPF) was remanufactured by ultrasonic wave treatment with various prepared solutions, followed by active component re-impregnation, and the emission control performance and surface properties of remanufactured DPF were studied at various remanufacturing conditions. The proper ultrasonic wave cleaning time at various prepared solutions and optimal re-impregnation amounts of active component for the best emission control performance of DPF were investigated and its performance tests were also carried out with various temperatures for the conversions of CO, THC (total hydrocarbon) and PM (particulate matter) by catalytic reaction test unit using bypass gas from the diesel engine dynamo system. It was found that the emission control performance of DPF remanufactured with the high-temperature air washing, ultrasonic wave cleaning at acid/base solutions and active component re-impregnation method was recovered to 95% level of its activity compared to that of the fresh DPF, which was caused by removing the deactivating materials from the surface of the DPF, through the analyses of performance test and their surface characterization by Optical microscope, EDX, ICP, TGA, and porosimeter.

• Restorative Dentistry and Endodontics
• /
• v.12 no.2
• /
• pp.45-53
• /
• 1987

The purpose of this study was to evaluate the tensile bond strength between composite resin and the human enamel. Three composite resin systems, two chemical (Clearfil Posterior, and Clearfil Posterior-3) and one light cure (Photo Clearfil-A), used with and without an intermediate resin (clearfil bonding agent), were evaluated under different amounts of load (10g, 200g and 200g for a moment) for in vitro tensile bond strength to acid-eched human enamel. Clinically intact buccal or lingual surfaces of 144 freshly extracted human permanent molars, embedded in acrylic were flattened with No #600 carborundum discs. Samples were randomly assigned to the different materials and treatments using a table of random numbers. Eight samples were thus prepared for each group(Table 2) these surfaces were etched with an acid etchant (Kurarey Co. Japan) in a mode of etching for 30 seconds, washing for 15 seconds, and drying for 30-seconds. During the polymerization of composite resin on the acid-etched enamel surfaces with and without bonding agent 10-gram, 200 gram and temporary 200 gram of load were applied. The specimens were stored in 50% relation humidity at $37^{\circ}C$ for 24 hours before testing. An universal Testing machine (Intesco model No. 2010, Tokyo, Japan) was used to apply tensile loads in the vertical directed (fig 5), and the force required for separation was recorded with a cross head speed of 0.25 mm/min and 20 kg in full scale. The results were as follow: 1. The tensile bond strength was much greater in applying a bonding agent than in not doing that. 2. The tensile bond strength of chemical cure composite resin was higher than that of light cure composite resin with applying on bonding agent on the acid-etched enamel. 3. In case of not applying a bonding agents on the acid-etching enamel, the highest tensile bond strength under 200 gram of load was measured in light cure composite resin. 4. The tensile bond strength under 200-gram of load has no relation with applying the bonding agent. 5. Under the load of 10-gram, There was significant difference in tensile bond strength as applying the bonding agent.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.12 no.4
• /
• pp.382-386
• /
• 1983

In order to utilize effectively sea mustard(Undaria pinnatifida) which is excellent in nutrition and medical action, powdered sea mustard juice was prepared and then its chemical composition and the stability of pigments were examined. Powdered sea mustard was made by washing fresh sea mustard with tap water to remove clay and sand, blanching at $85^{\circ}C$ for 20 sec in mixing solution(3% salt+1% $MgCO_3$), hot air drying($50-55^{\circ}C$, 3 hrs) after draining and pulverizing dried sea mustard to 200mesh. And then powdered sea mustard mixtures for juice type beverage was made by adding 0.75% of salt, 1.25% of sugar, 0.2% of ascorbic acid, 0.25% of flour of roasted barley and 0.8% of pulverized sea mustard to 100ml of water. Chemical composition of product was not scarcely changed during processing while amino-nitrogen content was increased and alginic acid and ash contents were decreased. The retention of chlorophyll and total carotenoid pigments of product against fresh sea mustard were 91.6% and 89.5% respectively. Judging from sensory evaluation, color, flavor, taste and dispersibility of powdered sea mustard juice were excellent and undesirable flavor of product was masked by addition of flour of roasted barley.

• Journal of the Korean Chemical Society
• /
• v.65 no.6
• /
• pp.433-440
• /
• 2021

Surfactants are organic compounds that have both hydrophilic and non-polar parts in one molecule, classified as non-ion, anion, cation, and amphoteric surfactants according to the charge of hydrophilic parts in aqueous state. A trace amounts may remain when vegetables and fruits are washed using type1 detergent (Vegetable and fruit detergent), and there is a possibility of exposure to the human body through ingestion. This study developed the simultaneous analysis method for 5 surfactants with LC-MS/MS for analysis of detergent residues after washing vegetables and fruits with detergent. The mobile phase used distilled water and acetonitrile containing 50 mM ammonium formate and 0.1% formic acid and was analyzed using a gradient method using XBridge BEH C8 column. The accuracy of the established method was 83.9-112.1%, and the precision was less than 20%. The detection limit was 7.0 (SLS) to 29.0 (SLES-N3) ㎍/L, and the correlation coefficient (r²) of calibration line regression was greater than 0.99, it is considered suitable for the analysis of trace amounts of surfactant components remaining in vegetables and fruits.

• Korean Chemical Engineering Research
• /
• v.56 no.2
• /
• pp.261-268
• /
• 2018

To prepare mesoporous $TiO_2$ ($meso-TiO_2$) with anatase and rutile crystal structures, hydrothermal and template synthesis were used. $Meso-TiO_2$ with anatase structure was obtained by hydrothermal synthesis. The crystal structure of $meso-TiO_2$ by hydrothermal synthesis converted from anatase to rutile by simple heating at $600^{\circ}C$ and above. However, their mesopore structure collapsed due to phase transition. To prepare $meso-TiO_2$ with rutile structure, template synthesis method was applied using mesoporous silica KIT-6 as a template. Once we incorporated anatase $TiO_2$ inside mesopores of silica, the phase transition temperature of $TiO_2$ confined inside KIT-6 was much higher ($900^{\circ}C$) than that of free-standing $TiO_2$ ($600^{\circ}C$). The suppression of $TiO_2$ phase transition inside mesopores of KIT-6 is closely related with the interaction between $TiO_2$ surface and silica walls in KIT-6 because oxygen vacancy in $TiO_2$ is regarded as the starting point for phase transition. After removal of silica template by NaOH solution washing, $meso-TiO_2$ with mixed phase between anatase and rutile was obtained.

• Journal of Food Hygiene and Safety
• /
• v.36 no.6
• /
• pp.510-519
• /
• 2021

The purpose of this study was to investigate the effect of the microbial reduction and quality maintenance of the physical and chemical pretreatment of Allium monanthum. For physical treatment, handwash, bubble wash and ultrasonication were conducted at 50℃ and 60℃ for 1, 3 and 5 minutes, respectively, and for chemical treatment the sample was immersed in fumaric acid and acetic acid of 1.5% and 2% concentrations for 1, 3 and 5 minutes, respectively. As a result of the microorganism and quality analysis, 3 minutes of bubble wash was the most effective physical pretreatment in reducing fungi although the effect on reducing total viable bacterial was small. Furthermore, 5 minutes of ultrasonication at 60℃ significantly reduced microorganisms, but also resulted in the reduction of the a value of chromaticity, which cause the green color to fade. With chemical pretreatment, it was found that treating with fumaric acid was more effective in reducing the total viable bacteria and fungi than acetic acid. The result shows that 1.5% concentration of fumaric acid is the most effective with 3 minutes of treatment time. The quality of Allium monanthum were compared in the combination of the two most effective microorganism reduction pretreatments: 3 minutes of bubble wash (B3) and 3 minutes in 1.5% fumaric acid (F153). As a result of analyzing the quality characteristics over 9 days of storage at 4℃ after the treatments, it was revealed that the BF treatment is more effective in reducing fungi than the total viable bacteria. The results shows that the BF treatment is more effective in reducing total viable bacteria, whereas the F153 treatment is more effective in reducing fungi. Also, it was found that the 𝚫E value in BF was the lowest, whereas F153 treatment showed the green color faded. The maximum cohesiveness changed more significantly in the green stems than in the roots. On the 9th day of storage, the hardness of the green stem was found to be maintained at the highest level (P<0.05) after F153 treatment, whereas that of the roots decreased (P<0.05) since the 6th day after the bubble wash. Considering the reduction of microorganisms and the quality maintenance of Allium monanthum, the most effective pretreatment methods were 3 minutes in 1.5% fumaric acid for reducing microorganisms and maintaining color and maximum cohesiveness, and the combined process could also be effective if the expiration period is within 3 days.

• Journal of Food Hygiene and Safety
• /
• v.31 no.4
• /
• pp.227-249
• /
• 2016

Arsenic and its compounds vary in their toxicity according to the chemical forms. Inorganic arsenic is more toxic and known as carcinogen. The provisional tolerable weekly intake (PTWI) of $15{\mu}g/kg$ b.w./week established by the Joint FAO/WHO Expert Committee on Food Additives (JECFA) has been withdrawn, while the EFSA panel suggested $BMDL_{0.1}$ $0.3{\sim}8{\mu}g/kg\;b.w./day$ for cancers of the lung, skin and bladder, as well as skin lesions. Rice, seaweed and beverages are known as food being rich in inorganic arsenic. As(III) is the major form of inorganic arsenic in rice and anaerobic paddy soils, while most of inorganic arsenic in seaweed is present as As(V). The inorganic arsenic in food was extracted with solvent such as distilled water, methanol, nitric acid and so on in heat-assisted condition or at room temperature. Arsenic speciation analysis was based on ion-exchange chromatography and high-performance liquid chromatography equipped with atomic absorption spectrometry and inductively coupled plasma mass spectrometry. However, there has been no harmonized and standardized method for inorganic arsenic analysis internationally. The inorganic arsenic exposure from food has been estimated to range of $0.13{\sim}0.7{\mu}g/kg$ bw/day for European, American and Australian, and $0.22{\sim}5{\mu}g/kg$ bw/day for Asian. The maximum level (ML) for inorganic arsenic in food has established by EU, China, Australia and New Zealand, but are under review in Korea. Until now, several studies have conducted for reduction of inorganic arsenic in food. Inorganic arsenic levels in rice and seaweed were reduced by more polishing and washing, boiling and washing, respectively. Further research for international harmonization of analytical method, monitoring and risk assessment will be needed to strengthen safety management of inorganic arsenic of foods in Korea.

• Korean Chemical Engineering Research
• /
• v.58 no.1
• /
• pp.84-91
• /
• 2020

The efficiency of the synthetic magnesium silicate used in basic polyols and edible oil purification is evaluated by its purification ability and filtration rate and is affected by the particle size and surface area of magnesium silicate. In this study, it was investigated the change on the particle size of magnesium silicate was influenced by the reaction temperature, injection rate, injection order (Si, Mg) and Mg/Si reaction mole ratio. The synthesized magnesium silicate was compared and analyzed for the synthesis, grinding, and refining processes. In the synthesis process, the reaction temperature and feed rate did not affect the average particle size change of magnesium silicate, while the reaction molar ratio of Mg / Si and the order of injection acted as main factors for the change of average particle size. The average particle size of magnesium silicate increased by 8.7 ㎛ from 54.4 ㎛ to 63.1 ㎛ at Mg injection when Mg molar ratio increased from 0.125 to 0.500, and increased by about 4.8 ㎛ from 47.3 ㎛ to 52.1 ㎛ at Si injection. The average particle size according to the order of injection was 59.1 ㎛ for Mg injection and 48.4 ㎛ for Si injection and the difference was shown 10.7 ㎛, therefore the filtration rate was about 2 times faster under the condition of Mg injection. That is, as the particle size increases, the filtration time is shortened and washing filtration rate can be increased to improve the productivity of magnesium silicate. The cake form of separated magnesium silicate after filtration becomes a solid through drying process and is used as powdery adsorbent through the grinding process. As the physical strength of the dried magnesium silicate increased, the average particle size of the powder increased and it was confirmed that this strength was affected by the reaction molar ratio. As the reaction molar ratio of Mg / Si increased, the physical strength of magnesium silicate decreased and the average particle size after grinding decreased by about 40% compared to the average particle size after synthesis. This reduction of strength resulted in an improvement of the refining ability due to the decrease of the average particle size and the increase of the amount of fine particle after the pulverization, but it resulted in the decrease of the purification filtration rate. While the molar ratio of Mg/Si was increased from 0.125 to 0.5 at Mg injection, the refining ability increased about 1.3 times, but the purification filtration rate decreased about 1.5 times. Therefore, in order to improve the productivity of magnesium silicate, the reaction molar ratio of Mg / Si should be increased, but in order to increase the purification filtration rate of the polyol, the reaction molar ratio should be decreased. In the synthesis parameters of magnesium silicate, the order of injection and the reaction molar ratio of Mg / Si are important factors affecting the changes in average particle size after synthesis and the changes of particle size after grinding due to the changes of compressive strength, therefore the synthetic parameter is an important thing that determines productivity and refining capacity.

• Korean Journal of Materials Research
• /
• v.4 no.8
• /
• pp.934-944
• /
• 1994

Effects of residual chloride on thermal decomposition behaviour of a-stannic acid and physical properties of $SnO_{2}$ powder were observed. The powder was fabricated by hydroxide method; $\alpha$-stannic acid was precipitated by mixing acqueous solutions of $SnCl_{4}$ and $NH_{4}$OH . The precipitate was washed with $NH_{4}NO_{3}$ solution while washing was controlled to be of three grades to modify its residual chloride content. The precipitate was dried at $1100^{\circ}C$ ~ 24h and calcined in air at $500^{\circ}C$ ~ $1100^{\circ}C$ for one hour. Thermal decomposition behaviour of $\alpha$-stannic acid was examined by a DT-TGA and a FTIR. Chemical composition and physical properties of $SnO_{2}$ powder were observed by an AES, a BET and a TEM, respectively. With a reduction in chloride content, the relative crystallite size of $SnO_{2}$ powder slightly increased by a low-temperature-calcining. However, at a high calcining temperature(T), the reverse relation occured. It was suggested that chloride ion replaces part of lattice oxygen site of a-stannic acid. Also, chloride ion on the site was suggested to retard de-hydration as well as crystalization at a low T while to promote crystal growth of $SnO_{2}$ by forming oxygen vacancy at a high T.