• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.3
• /
• pp.203-212
• /
• 2005

Cellulose insulation is primarily manufactured from recycled newsprint and treated with fire retardants for the fire resistance. Thanks to the fire retardants, it is not combustible and flammable. In addition to that, Its thermal resistance is much better than that of fiberglass or rock wool. It is made from waste paper and easily decayed when it is demolished, and it has small embodied energy. So it is very environment-friendly building material. For broader use of cellulose insulation in buildings in Korea, it is necessary to test its physical performance to compare the results with the requirements on the Korean Building Code. To this end, apparent thermal conductivity (ka) measurements of Korean-made loose-fill cellulose insulations were recently completed using equipment that was built and operated in accordance with ASTM C 518 and the fire resistance was tested in accordance with ASTM C 1485. Korean loose-fill cellulose has thermal conductivity about 5% greater than the corresponding U.S. product at the same density. This is likely due to differences in the recycled material being used. Both spray-applied and loose-fill cellulose insulation lose about 1.5% of their thermal resistivity for $5.5^{\circ}C$ increase in temperature. The fire resistance of cellulose insulation is increased in linear proportion to the increase of the rate of fire retardant. Thanks to the high fire resistance, cellulose insulation can be used as a substitution of Styrofoam or Urethane foam which is combustible. The thermal conductivity of cellulose insulation was $0.037-0.043W/m{\cdot}K$ at the mean specimen temperature from $4-43^{\circ}C$. It corresponds to the thermal resistance of "Na Grade" according to the Korean Building Code. The effect of chemical content on thermal conductivity was negligible for all but the chemical-free specimen which had the highest value for the thermal conductivity over the temperature range tested. The thermal resistance of cellulose insulation is better than that of fiberglass or rock wool, and its fire resistance is higher than that of Styrofoam or Urethane foam. Therefore it can be substituted for those above considering its physical performance. Cellulose insulation is no more expensive than Styrofoam or rock wool, so it is recommended to use it more widely in Korea.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.26 no.1
• /
• pp.52-72
• /
• 1984

This study was performed to obtain the basic data which can be applied to the use of epoxy resin mortars. The data was based on the properties of epoxy resin mortars depending upon various mixing ratios to compare those of cement mortar. The resin which was used at this experiment was Epi-Bis type epoxy resin which is extensively being used as concrete structures. In the case of epoxy resin mortar, mixing ratios of resin to fine aggregate were 1: 2, 1: 4, 1: 6, 1: 8, 1:10, 1 :12 and 1:14, but the ratio of cement to fine aggregate in cement mortar was 1 : 2.5. The results obtained are summarized as follows; 1.When the mixing ratio was 1: 6, the highest density was 2.01 g/cm$^3$, being lower than 2.13 g/cm$^3$ of that of cement mortar. 2.According to the water absorption and water permeability test, the watertightness was shown very high at the mixing ratios of 1: 2, 1: 4 and 1: 6. But then the mixing ratio was less than 1 : 6, the watertightness considerably decreased. By this result, it was regarded that optimum mixing ratio of epoxy resin mortar for watertight structures should be richer mixing ratio than 1: 6. 3.The hardening shrinkage was large as the mixing ratio became leaner, but the values were remarkably small as compared with cement mortar. And the influence of dryness and moisture was exerted little at richer mixing ratio than 1: 6, but its effect was obvious at the lean mixing ratio, 1: 8, 1:10,1:12 and 1:14. It was confirmed that the optimum mixing ratio for concrete structures which would be influenced by the repeated dryness and moisture should be rich mixing ratio higher than 1: 6. 4.The compressive, bending and splitting tensile strenghs were observed very high, even the value at the mixing ratio of 1:14 was higher than that of cement mortar. It showed that epoxy resin mortar especially was to have high strength in bending and splitting tensile strength. Also, the initial strength within 24 hours gave rise to high value. Thus it was clear that epoxy resin was rapid hardening material. The multiple regression equations of strength were computed depending on a function of mixing ratios and curing times. 5.The elastic moduli derived from the compressive stress-strain curve were slightly smaller than the value of cement mortar, and the toughness of epoxy resin mortar was larger than that of cement mortar. 6.The impact resistance was strong compared with cement mortar at all mixing ratios. Especially, bending impact strength by the square pillar specimens was higher than the impact resistance of flat specimens or cylinderic specimens. 7.The Brinell hardness was relatively larger than that of cement mortar, but it gradually decreased with the decline of mixing ratio, and Brinell hardness at mixing ratio of 1 :14 was much the same as cement mortar. 8.The abrasion rate of epoxy resin mortar at all mixing ratio, when Losangeles abation testing machine revolved 500 times, was very low. Even mixing ratio of 1 :14 was no more than 31.41%, which was less than critical abrasion rate 40% of coarse aggregate for cement concrete. Consequently, the abrasion rate of epoxy resin mortar was superior to cement mortar, and the relation between abrasion rate and Brinell hardness was highly significant as exponential curve. 9.The highest bond strength of epoxy resin mortar was 12.9 kg/cm$^2$ at the mixing ratio of 1:2. The failure of bonded flat steel specimens occurred on the part of epoxy resin mortar at the mixing ratio of 1: 2 and 1: 4, and that of bonded cement concrete specimens was fond on the part of combained concrete at the mixing ratio of 1 : 2 ,1: 4 and 1: 6. It was confirmed that the optimum mixing ratio for bonding of steel plate, and of cement concrete should be rich mixing ratio above 1 : 4 and 1 : 6 respectively. 10.The variations of color tone by heating began to take place at about 60˚C, and the ultimate change occurred at 120˚C. The compressive, bending and splitting tensile strengths increased with rising temperature up to 80˚ C, but these rapidly decreased when temperature was above 800 C. Accordingly, it was evident that the resistance temperature of epoxy resin mortar was about 80˚C which was generally considered lower than that of the other concrete materials. But it is likely that there is no problem in epoxy resin mortar when used for unnecessary materials of high temperature resistance. The multiple regression equations of strength were computed depending on a function of mixing ratios and heating temperatures. 11.The susceptibility to chemical attack of cement mortar was easily affected by inorganic and organic acid. and that of epoxy resin mortar with mixing ratio of 1: 4 was of great resistance. On the other hand, when mixing ratio was lower than 1 : 8 epoxy resin mortar had very poor resistance, especially being poor resistant to organicacid. Therefore, for the structures requiring chemical resistance optimum mixing of epoxy resin mortar should be rich mixing ratio higher than 1: 4.

• Korean Chemical Engineering Research
• /
• v.45 no.6
• /
• pp.656-662
• /
• 2007

Fuel reformer using plasma and shift reactor for CO oxidation were designed and manufactured as $H_2$ supply device to operate a polymer electrolyte membrane fuel cell (PEMFC). $H_2$ selectivity was increased by non-thermal plasma reformer using GlidArc discharge with Ni catalyst simultaneously. Shift reactor was consisted of steam generator, low temperature shifter, high temperature shifter and preferential oxidation reactor. Parametric screening studies of fuel reformer were conducted, in which there were the variations of the catalyst temperature, gas component ratio, total gas ratio and input power. and parametric screening studies of shift reactor were conducted, in which there were the variations of the air flow rate, stema flow rate and temperature. When the $O_2/C$ ratio was 0.64, total gas flow rate was 14.2 l/min, catalytic reactor temperature was $672^{\circ}C$ and input power 1.1 kJ/L, the production of $H_2$ was maximized 41.1%. And $CH_4$ conversion rate, $H_2$ yield and reformer energy density were 88.7%, 54% and 35.2% respectively. When the $O_2/C$ ratio was 0.3 in the PrOx reactor, steam flow ratio was 2.8 in the HTS, and temperature were 475, 314, 260, $235^{\circ}C$ in the HTS, LTS, PrOx, the conversion of CO was optimized conditions of shift reactor using simulated reformate gas. Preheat time of the reactor using plasma was 30 min, component of reformed gas from shift reactor were $H_2$ 38%, CO<10 ppm, $N_2$ 36%, $CO_2$ 21% and $CH_4$ 4%.

• Korean Journal of Food Science and Technology
• /
• v.7 no.4
• /
• pp.200-207
• /
• 1975

This experiment was carried out to investigate the chemical composition and microflora of soy sauce during storage under the different temperature. The results obtained are as follows. (1) Total nitrogen, color density, specific gravity and sodium chloride concentration of soy sauce showed a increasing tendency in the progress of storage period. Open-storage state at $30^{\circ}C\;and\;15^{\circ}C$ were responsible to the increase of components as compare with close-storage state at $5^{\circ}C$. (2) pH and buffer action were not almost changed during the storage. (3) Alcohol and sugar contents of soy sauce showed a decreasing tendency in the process of storage period, especially in the case of open state alcohol being almost disappeared within 11 months in all groups. (4) The number of common bacteria in one ml of soy sauce were counted as $96{\times}10^4$ before pasteurization and $10^3$ after pasteurization. The osmophilic bacteria was counted as $38{\times}10^4$, $10^2$ after pasteurization. (5) The spore number of mold in one ml of soy sauce were counted $32{\times}10^7$ before pasteurization, 58 after pasteurization and 10 to $10^2$ in the progress of storage period. (6) The bacteria number of soy sauce were somewhat decreased with the passing, of the time. The group of high temperature and open state were more notable than low temperature and close state.

• Journal of Sericultural and Entomological Science
• /
• v.24 no.2
• /
• pp.55-72
• /
• 1983

These studies were done to find out any difference, ultrastructural, physical or chemical, between the shells of diapausing and non-diapausing eggs of the silkworm, Bombyx mori L. 1. From the electron-microscopic observation, the egg shells have four distinctive layers. In addition to the four layers, the shells in the diapausing eggs has another layer with low electron density on its surface. 2. The permeability of the egg shell to hydrochloride was much lower in diapausing egg than in non-diapausing egg. Also the permeability changed in the opposite directions with the egg age: the diapausing eggs decreased while non-diapausing ones increased. 3. The permeability increased when the diapausing egg shell was treated with HCl. When they were treated with ether, however, the increase in permeability was much smaller. It seems there was an ether soluble material involved in the content of the egg shell. 4. The diapausing eggs were also much more resistant to desiccation than the non-diapausing ones. The former, when treated with HCl or chilling, became less resistant to desiccation. 5. The positive histochemical response of the egg shell to PAS-Alcian blue and protein stainings suggests presence of abundant proteins and carbohydrates in the egg shell. On the other hand, the staining response to lipid was more positive in the inner layers than in the outer layer of the shell. 6. The egg shell adhesives seems to be mucopolysaccharides produced by colleterial glands, since the oviposited eggs showed a positive responses to carbohydrate and negative to lipid-staining chemicals, but not the mature oocytes in the ovarioles. 7. There were two bands on the electrophoretic pattern of the SH proteins extracted from the egg shells both in the diapausing egg and non-diapausing one: a slow moving major component and a fast moving minor one. However, the electrophoretic mobility showed a difference in the minor components between them. It is evident that the fast moving minor one of non-diapausing egg ran a little further than that of diapausing egg. 8. In amino acids analysis, no significant differences were found in their composition between diapausing and non-diapausing egg and SH proteins contain relatively more glycine and less cystine.

• Journal of Life Science
• /
• v.17 no.12
• /
• pp.1701-1708
• /
• 2007

Seed pelleting is generally conducted in order to save the labor for sowing and thinning by enabling the precision mechanical planting. In the present study, the influence of physical and chemical properties of pelleting solid materials was investigated on carrot seed germination. Among the pelleting solid materials evaluated, dialite, kaolin, and talc showed low bulk density and high porosity. Bentonite and dialite carried high water holding capacities of 184% and 173%, respectively, while calcium carbonate, calcium oxide, and fly ash showed relatively low water holding capacity. The pH of kaolin (6.8) and dialite (7.4) were close to neutral, while limestone (12.8), calcium oxide (13.0), and bentonite (10.0) were highly basic. High electro-conductivity was shown in limestone and calcium oxide. EDS analysis revealed that the main elemental compositions of talc were Si (71.0%) and Mg (29.0%), and those of calcium carbonate were Ca (66.6%), Si (22.9%), and Mg (10.5%). High granulation capacity was observed from talc and the mixture of talc and calcium carbonate. Seeds pelleted with bentonite showed the highest hardness. The dissolving type of the pellet layer after imbibition was split type in talc, limestone, zeolite, and fly ash, melt type in calcium carbonate and calcium oxide, and swell type in bentonite and vermiculite. The shortest dissolving time of pellet layer was observed from calcium carbonate and kaolin. The germination speed $(T_{50})$ was delayed as the size of pelleted seeds increased. The optimum size of pelleting was 19 ratio in carrot.

• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.5
• /
• pp.847-852
• /
• 2011

Green manure crops are mainly used to reduce the application of chemical fertilizers. Mixture of green manure crops have beneficial effects in agroecosystem. In this study, experiments were conducted to evaluate the effects of monoculture and mixtures of crimson clover (Trifolium incarnatum) on rice growth and yield in paddy. This experiment was conducted at Sinheung series (fine loamy, mixed, nonacid, mesic family of Fluvaquentic Endoaquepts) from Oct. 2007 to Oct. 2009 at the National Institute of Crop Science (NICS), RDA, Suwon, Gyeonggi province, Korea. Seeding rates of crimson clover (CC) were consisted of monoculture (CC2, 3, 4 kg and hairy vetch 5 kg $10a^{-1}$) and mixtures (CC 2 + barley 7, CC 3 + barley 7, CC 4 + barley 7, and CC2 + hairy vetch $5kg\;10a^{-1}$). Seeds were drilled by partial tillage machine on 9th Oct. in 2007. Monoculture and mixture of crimson clover as a green manure crop was incorporated in soil for rice cultivation on 15th May in 2008. Chemical fertilizers had not been applied to monoculture and mixture plots. The biomass and N production of monoculture plots were lower than mixture plots. The biomass and N production of CC 2 + hairy vetch $5kg\;10a^{-1}$ plot were the highest among mixtures treatments. In rice growing season, ammonium nitrogen concentrations in soil were a little high trends at CC 2 + hairy vetch $5kg\;10a^{-1}$ plot. And soil bulk density and porosity were improved at mixture plot after rice harvesting. The rice yield of CC 2 + hairy vetch $5kg\;10a^{-1}$ plot was not significantly different from conventional practice plot. These results indicated that cropping of crimson clover with hairy vetch mixture was better than barley mixture for environmental friendly rice cultivation.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.6
• /
• pp.981-986
• /
• 2010

This study was carried out to investigate the effects of fertilizer and organic resource annual dressing for 30 years of Jeonbug series (silt loam) on soil properties and rice N uptake in paddy field soil. In the study field, treatments including control (NPK), NPK+rice straw, NPK+rice straw compost and nitrogen fertilization levels at 0, 100, 150, 200, 250 kg $ha^{-1}$ have been imposed for 30 years. Soil hardness and bulk density decreased from 15.7 mm and 1.381 Mg $m^{-3}$ in the control to 12.5 mm and 1.244 Mg $m^{-3}$ in NPK+rice straw compost treatment, respectively, indicating improvement of soil physical conditions such as porosity. Co-application of straw compost with NPK also result in a better chemical properties than NPK alone as it increased available phosphate (from 96 to 133 mg $kg^{-1}$), available silicate (from 81 to 116 mg $kg^{-1}$), and cation exchange capacity (from 9.8 to 11.4 $cmol_c\;kg^{-1}$). Soil organic matter concentration of top soil (0 to 7.5 cm in depth) was higher in NPK+rice straw and NPK+rice straw compost than in control. Fertilizer N uptake amount was much higher in NPK+rice straw (nitrogen fertilization level; 250 kg $ha^{-1}$) and NPK+rice straw compost (nitrogen fertilization levels; 200, 250 kg $ha^{-1}$) plots compared to the control (nitrogen fertilization level; 100 kg $ha^{-1}$) plot. Nitrogen use efficiency was showed significantly high in the NPK+rice straw compost (nitrogen fertilization levels; 100, 150 kg $ha^{-1}$) plot compared to the control (nitrogen fertilization level; 100 kg $ha^{-1}$) plot. Therefore, it was suggested that application of organic inputs is helpful in improving soil fertility and physical conditions and thus in N uptake.

• Korean Chemical Engineering Research
• /
• v.59 no.4
• /
• pp.548-556
• /
• 2021

This study was conducted to investigate the applicability of lignocellulosic fiber and coconut shell activated carbon (CSA) for the production of a particulate matter (PM)-reducing air-filter as raw materials to solve the environmental problems of non-woven fabrics. CSA had a good potential to use as a raw material of air-filter for reducing volatile organic compounds as well as noxious metals, and reduction capability of the CSA was 5 times higher than that of wood fiber. Natural adhesives formulated with proteinaceous wastes mostly were applied successfully to fabricate air-filters with the shape of fiberboard. The air-filter fabricated with the minimum target density of 200 kg/m³ and the maximum CSA-content of 40 wt% in fiberboard had a good manageable strength. However, the fiberboard filters was required to make vent-holes for improving an air-permeability of the filters. Size of the CSA particles was adjusted to greater than 2 mesh with the consideration of strength and formability of the fiberboard. Three-layers fiberboard that only wood fiber and the mixture of wood fiber and CSA were formed in the surface and middle layers, respectively, was determined to the optimal condition for the production of air-filters. In addition, traditional Korean paper handmade from mulberry trees (TKP) showed a good PM-reducing property as an air-filter. It is concluded that air-filtering set composed of fiberboard with vent-holes and TKP instead of conventional air-filters made with non-woven fabrics can be used as a filter for reducing the concentrations of PM, VOC and noxious metals existed in indoor and outdoor spaces.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.11-18
• /
• 2021

A novel microwave dielectric composite material for ultra-low temperature co-fired ceramics (ULTCC) with (1-x)BaWO₄-xBaV₂O₆ (x=0.54~0.85) composition was prepared by firing a mixture of BaWO₄ and BaV₂O₆. Shrinkage tests showed that the ceramic composite begins to densify at a temperature as low as 550℃ and can be sintered at 650℃ with 98% of relative density under the influence of BaV₂O₆. X-ray diffraction analysis showed that BaWO₄ and BaV₂O₆ coexisted and no secondary phase was detected in the sintered bodies, implying good chemical compatibility between the two phases. Near-zero temperature coefficients of the resonant frequency (𝛕_f) could be achieved by controlling the relative content of the two phases, due to their positive and negative 𝛕_f values, respectively. With increasing BaV₂O₆ (x from 0.53 to 0.85), the 𝛕_f value of the composites increased from -7.54 to 14.49 ppm/℃, ε_r increased from 10.08 to 11.17 and the quality factor (Q×f value) decreased from 47,661 to 37,131 GHz. The best microwave dielectric properties were obtained for x=0.6 samples with ε_r=10.4, Q×f=44,090 GHz, and 𝛕_f=-2.38 ppm/℃. Chemical compatibility experiments showed the developed composites are compatible with aluminum electrode during co-firing process.