• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.95-98
• /
• 1998

Fly ash is glassy dust collected from coal fired power plant. Recently, much research for fly ash conducted in Korea and fly ash is a valuable material especially when it used in high strength, high flowable, high durability concrete. But it varies with coal source, coal grinding and boiler conditions. Therefore, it is important that quality control of fly ash itself to get high quality concrete. In this study, over 20 samples of Poryong and Samchonpo fly ashs are tested and analyzed. The physical, chemical properties of fly ash and their relationships are investigated and it can be applied to quality control of concrete.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.11
• /
• pp.1100-1106
• /
• 2004

In this report, a self-organizing fuzzy neural network is proposed to control chemical feeding, which is one of the most important problems in water treatment process. In the case of the learning according to raw water quality, the self-organizing fuzzy network, which can be driven by plant operator, is very effective, Simulation results of the proposed method using the data of water treatment plant show good performance. This algorithm is included to chemical feeder, which is composed of PLC, magnetic flow-meter and control valve, so the intelligent control of chemical feeding is realized.

• Food Science of Animal Resources
• /
• v.36 no.5
• /
• pp.617-625
• /
• 2016

Pastırma, a dry-cured meat product, is produced from the whole muscle and/or muscles obtained from certain parts of beef and water buffalo carcasses. The purpose of this study was to determine the effects of different levels of sodium nitrite on changes in the physicochemical and microbial quality during the production of pastırma. The changes in residual nitrite, salt, pH, moisture, thiobarbutiric acid reactive substances (TBARS), colour (L*, a*, b*), total aerobic mesophilic bacteria (TAMB), lactic acid bacteria (LAB), Micrococcus/Staphylococcus (M/S), mould-yeast (M-Y), and Enterobacteriaceae counts of pastırma with 0, 50, 100 and 150 ppm sodium nitrite were determined during the production. The nitrite levels and the production stages had significant effects (p<0.01) on residual nitrite, TBARS, pH, salt, and colour values. The TBARS values of the pastırma with nitrite were significantly lower (p<0.05) than the control. The final TAMB, LAB, M/S, and M-Y counts of pastırma with 150 ppm nitrite were significantly (p<0.05) lower than the control. Also, the a* (relative redness) values of control pastırma were significantly lower (p<0.05) than the pastırma with nitrite. The production stages had a significant effect (p<0.01) on the moisture.

• Korean Chemical Engineering Research
• /
• v.46 no.6
• /
• pp.1043-1051
• /
• 2008

In polyolefin processes melt index (MI) is the most important controlled variable indicating product quality. Because of the difficulty in the on-line measurement of MI, a lot of MI estimation and correlation methods have been proposed. In this work a new dynamic MI estimation scheme is developed based on system identification techniques. The empirical MI estimation equation proposed in the present study is derived from the $1^{st}$-order dynamic models. Effectiveness of the present estimation scheme was illustrated by numerical simulations based on plant operation data including grade change operations in high density polyethylene (HDPE) processes. From the comparisons with other estimation methods it was found that the proposed estimation scheme showed better performance in MI predictions. Using the model predictive control method based on the present dynamic MI estimation model, MI values are estimated and compared with those of MI setpoints. From the numerical simulation of the proposed control system, it was found that significant reduction of transition time and the amount of off-spec during grade changes were achieved.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.05a
• /
• pp.217-220
• /
• 2001

In the shearing process the burr or rollover must be minimized in order to improve the quality of product. The burr size can be minimized by control of several process parameters. But removal of all burrs are impossible. Most mechanical type deburring methods (vibrating bowls, rotating barrels, shot blasting, for example.) will remove large burrs, other methods use chemical (electro-chemical deburring) or heat (thermal energy deburring). The electro-chemical deburring process removes burrs by the deplating method. Electro-chemical deburring equipment is requires a small capital investment than other methods(mechanical or thermal methods). Electro-chemical deburring method need to many parameters for control such as a time, voltage and concentration of electrolyte. In this paper shows relations of these parameters by experiment.

• Natural Product Sciences
• /
• v.10 no.4
• /
• pp.141-151
• /
• 2004

Platycodi Radix, as one of the most important traditional oriental materia medica, is utilized frequently in clinical practice and dietary in China, Korea, and Japan. To evaluate definitely the quality of Platycodi Radix, and provide scientific data for commodity circulation, new product development and clinical application of Platycodi Radix, we summarized its medical history, application status, chemical compositions, bioactivities, cultivation, international circulation, quality evaluation, dosage and safety, and brought forward some constructive suggestions on further establishment of international criteria for quality control of Platycodon grandiflorum.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.13 no.1
• /
• pp.15-22
• /
• 2006

An experiment was conducted to study the efficiency of cyanobacterial biofertilizer (CBB) with chemical (NPK) fertilizer on quantitative and qualitative characters of mulberry variety Kanva-2. Their influences on silkworm growth and cocoon characters were also studied. Ten different CBB and NPK fertilizer treatments were given to 5000 plants of established mulberry garden. Treatments were of four types viz., (i) T1 to T7: single and combination dose of CBB+50% NPK (ii) T8: combination dose of CBB + 25%NPK, (iii) T9: CBB only and (iv) T10: control-l00% NPK. Soil pH decreased and nutrients status increased in CBB (T1- T9) treated plots. Average of ten crops data on quantitative traits revealed that T7 (CBB [N. muscorum (1.0 g), A. variahilis (1.0) and S. millei (1.0 g)] + 50% NPK) was very effective in improving growth parameters. Leaf yield was also found high in treatment T7 (32.12 tons/ha/yr.) followed by T10 (31.17 tons/ha/yr.) and T8 (27.67 tons/ha/yr.). Leaf quality characters were found high in T7 and low in T9. Most of the quality traits in T7 are on par with control no. The results revealed that reduction in the dose of chemical fertilizers in T7 did not affect the leaf yield and leaf quality traits of mulberry. This clearly indicates that the efficiency of CBB (T7) provides nitrogen, increases essential nutrients available in soil, maintain soil pH and supply growth substances required for the improvement of leaf yield and leaf quality of mulberry. Bioassay study also revealed no significant difference in silkworm growth and cocoon characters between treatments T7 and T10. Economics calculated revealed that T7 is highly economical and beneficial over T10 by gaining an amount of Rs. 660/-/acre/crop. Thus, treatment T7 containing N. muscorum (1.0 g), A. variahilis (1.0 g) and S. millei (1.0 g) + 50% NPK fertilizers can be recommended to sericulturists mainly to reduce the use of NPK fertilizers, by saving 50% of its cost and to improve soil fertility conditions, which in turn improves leaf yield and quality of mulberry.

• Korea-Australia Rheology Journal
• /
• v.21 no.2
• /
• pp.83-89
• /
• 2009

Coating process plays an important role in information technology such as display, battery, chip manufacturing and so on. However, due to complexity of coating material and fast deformation of the coating flow, the process is hard to control and it is difficult to maintain the desired quality of the products. Moreover, it is hard to measure the coating process because of severe processing conditions such as high drying temperature, high deformation coating flow, and sensitivity to the processing variables etc. In this article, the coating process is to be re-illuminated from the rheological perspectives. The practical approach to analyze and quantify the coating process is discussed with respect to coating materials, coating flow and drying process. The ideas on the rheology control of coating materials, pressure and wet thickness control in patch coating process, and stress measurement during drying process will be discussed.

• Biomedical Science Letters
• /
• v.13 no.4
• /
• pp.361-368
• /
• 2007

Biological samples can be fixed either by chemical method by using chemical solution or physical methods by using heat treatment. The problem in traditional heat fixation is unsatisfactory quality due to uneven heat conduction in specimen and loss of inner cell contents. Chemical fixation method also bears several intrinsic problems like the limit in specimen size, time consumption in fixative impregnation, and loss of low molecular weight cell components. These factors deteriorate the quality of fixed specimen, thus limit the magnification and contrast of tissue pictures. Microwave heat has been reported to be a good alternative to current chemical methods to overcome these problem. In this study, we tried to introduce the microwave energy method to routine fixation work in hospital. We replaced chemical fixative with saline to provide moderate reaction condition, and used frozen section to reduce time for sample preparation. Temperature was measured at each experiment. The fixation of rat kidney tissue with 2.45 GHz electromagnetic wave and saline showed similar result to the control group fixed with traditional chemical method. Human tumor tissue fixed with 2.45 GHz electromagnetic in frozen section was improved in terms of histochemistry of PAS and immunohistochemistry of tumor marker like cytokeratin. Total turnaround time was reduced from $24\sim38$ h to to $2\sim4$ h. In conclusion, the quality of samples prepared by microwave heating method was at least as good as that of traditional method. If the condition for the fixation of different specimens is standardized, this new method could be applied to routine work in hospital, and could save working time as well.

• Transactions on Control, Automation and Systems Engineering
• /
• v.4 no.1
• /
• pp.62-74
• /
• 2002

The tracking of a reference temperature trajectory in a polymerization batch reactor is a common problem and has critical importance because the quality control of a batch reactor is usually achieved by implementing the trajectory precisely. In this study, only energy balances around a reactor are considered as a design model for control synthesis, and material balances describing concentration variations of involved components are treated as unknown disturbances, of which the effects appear as time-varying parameters in the design model. For the synthesis of a tracking controller, a method combining the input-output linearization of a time-variant system with the parameter estimation is proposed. The parameter estimation method provides parameter estimates such that the estimated outputs asymptotically follow the measured outputs in a specified way. Since other unknown external disturbances or uncertainties can be lumped into existing parameters or considered as another separate parameters, the method is useful in practices exposed to diverse uncertainties and disturbances, and the designed controller becomes robust. And the design procedure and setting of tuning parameters are simple and clear due to the resulted linear design equations. The performances and the effectiveness of the proposed method are demonstrated via simulation studies.