• Journal of the Korean Ceramic Society
• /
• v.35 no.12
• /
• pp.1337-1342
• /
• 1998

To investigate an effect of phase separation on precipitation characteristics of ZnS microcrystals in ma-trix glass ZnS doped borosilicate glasses for nonlinear optical applications were prepared by melting and pre-cipitation process. ZnS dopant contributed to phase separation promotion which increased the phase separa-tion of the matrix glass within immiscibility region. It was also found that ZnS as phase separation promoter showed a similar contribution for some selected glass compositions in miscibility region. The precipitation of ZnS microcrystals occurred in thephase separable glass compoitions. The radius of ZnS microcrystals in-creased with increasing the heat treatment temperature and Na2O contents of matrix glass composition. The ZnS particle sizes estimated by effective mass approximation ranged from about 30 to 80${\AA}$ It was suf-ficiently small to show quantum confinement effect.

• Journal of the Korean Ceramic Society
• /
• v.32 no.12
• /
• pp.1331-1336
• /
• 1995

The glass-ceramics for ferro-electric were made from compositions of 70PbO.16TiO2.8SiO2.4B2O3.2AlPO4 (wt%) and 67.5PbO.20TiO2.8.5SiO2.2B2O3.2AlPO4 (wt%). The crystallization kinetics for PbTiO3 crystalline phase formation from glass was studied using non-isothermal DSC techniques. The values of activation energy, ΔE using variables of heating rate and temperature were calculated at various reaction fractions obtained from peak area over DSC. The results indicated that activation energy was lowest at 60% reaction fractions and the activation energy of glass containing 20.0 wt% TiO2 is higher than that of glass containing 16.0 wt% TiO2. The crystallization mechanism was three dimensional growth (n=4).

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2002.11a
• /
• pp.97-102
• /
• 2002

The Purpose of this study was to investigate the exterior materials of super high-rise housing more than 30 stories which were built in New York City between 1924 and 2004. The result of examining 153 buildings was as follows; Exterior materials of super high-rise housing which were used bricks, of the salt-glazed bricks, terra-cotta and ceramic tiles, jumbo bricks and bricks were preferred among them. The colour of bricks was yellow, yellow ochre, clear brown, brown, dark brown, orange, vermilion and red. Exterior materials of super high-rise hotel and hotel apartment were bricks and ceramic tiles in the early days but stones, curtain wall and glass(green glass, green-tinted glass, brown-tinted glass, black glass) after 1980s. The main colour of buildings extended gray, green, blue-tinted brown-tinted and black.

• Journal of the Korean Ceramic Society
• /
• v.37 no.1
• /
• pp.82-89
• /
• 2000

In lithium silicate photosensitive glass-ceramics, the relationship between lithography time and crystallization, and the effect of addition of mineral acid in etching rate and pattern shape were investigated. Irradiation times for micropatterning were less than 5 minutes in which Ce3+ ions in glass were changed rapidly to Ce4+ with ultra violet light. Overexposure to ultra brought about blot of pattern by diffiraction of light. Addition of mineral acid to HF enhanced etching rate as compared with HF solution only. The addition of H2SO4 especially increased the etching rate by 70%. But the mixed solution also increased the etching rate of the noncrystallized portion of the glass and this resulted in heavy etching. Etching with ultrasonic wave showed higher etching rate than that with the static or fluid method.

• Journal of the Korean Ceramic Society
• /
• v.52 no.2
• /
• pp.119-122
• /
• 2015

Laser sealing with glass frits appears a promising technology for sealing various electronic devices (e.g., solar cells, displays) due to its several advantages. The purpose of this study is to understand the relationship between the composition of glasses and their laser-heating conditions. To allow glass to be sealed using laser heating, CuO was added to two different glass systems, in different amounts. The optical absorptivity of the glass samples was related directly to their CuO content. The laser-heating temperature and the CuO content exhibited a proportional relationship. Furthermore, the heating temperature increased linearly with the laser power used. From these results, we could determine the appropriate laser-heating conditions and CuO content for sealing electronic devices using laser-sealing technology.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.189-192
• /
• 2012

Manufacturing process for silicate glass phosphors containing Eu2+ activator and their photoluminescence property have been studied. We adopted powder sintering process instead of traditional glass melting process for making glass phosphor. At first, phosphor powders were synthesized at 1200 ℃ for 2-3 hours under a reducing atmosphere with 10% H2-90% N2 gas mixture. The reduced powders were compacted into discs and then the discs weresintered at 1400 ~ 1500 ℃ for 1 hr under a reducing atmosphere of 5H2-95% N2. The enhancement of PL intensity by Al2O3 addition, XPS binding energy shift of Si 2p and O 1s, sintering shrinkage, and crystallization were characterized.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.298-307
• /
• 2019

Two types of CaO-Al₂O₃-SiO₂ (CAS) glass powder applied spray coating on the surface of sintered Al₂O₃ were researched for sintering behavior; (1) Si-rich, glass containing high content SiO₂, (2) Ca-rich, containing high content CaO. Foaming of bubbles remaining inside the Ca-rich glass was produced at a viscosity of approximately 10⁷~10⁹ poise, resulting in decreasing shrinkage (interfering with sintering) and increasing surface roughness. In case of Si-rich glass, there was no serious foaming bubbles phenomenon like Ca-rich below 1000℃, however cristobalite crystals with low density occurred at 1200℃ and then produced re-foaming of bubbles, resulting in abnormal sintering behavior. These phenomenon is considered to be a decrease in viscosity due to an increase in the Ca content of the glass according to the formation of low-density cristobalite crystals. Therefore, in case of CAS glass, it is necessary to consider the increase of surface roughness and the sintering interference because of foaming bubbles phenomenon at low temperature sintering. Especially, when containing high SiO₂ content, abnormal foaming phenomenon due to crystallization at high temperature should be predicted.

• Journal of Technologic Dentistry
• /
• v.21 no.1
• /
• pp.115-121
• /
• 1999

This investing was carried out to evaluate the alteration of stress distribution on teeth and esthetic crowns. Analyzing the stress distribution by the two-dimensional finite element methods, a model of lower 1st molar according to the porcelain fused metal crown an the porcelain fused glass ceramic core crown and the all glass ceramic crown. 1. The pattern of stress distribution showed no apparent differences. 2. The greatest von Mises values were concentrated around the central fossa of all esthetic crowns. The greatest Maximum principle value were concentrated around the interface between the base of esthetic crown and the abutment tooth. It was found that the apatite glass ceramic could be applicable for use in dental crown prosthesis.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.3
• /
• pp.102-107
• /
• 2007

Dielectric layer of phosphate glass for plasma display panel (PDP) device made by silk screen printing on soda-lime glass. For regulate thermal expansion coefficient (CTE) of between substrate glass and dielectric layer use addition of $Al_2O_3$ and $TiO_2$. The crystallization process of glass-ceramics for dielectric layer have been examined by DTA, XRD some of optical, electrical properties of the dielectric layer were evaluated by UV-spectrometer, dilatometer, impedance analyser. The principal crystalline phase was identified as zinc metaphosphate [$Zn(PO_3)_2$] and zinc pyrophosphate [$Zn_2P_2O_7$]. Reflectance and dielectric constance increased with the addition of $TiO_2$ filler, dielectric constant lower the out side reflectance unchanging of the adding of $Al_2O_3$ filler. Besides CTE was at about $62{\times}10^{-7}/^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.46 no.2
• /
• pp.175-180
• /
• 2009

Multilayer ceramic capacitors (MLCCs) have continually been made smaller in size and larger in capacity in resent years. However, the end termination electrode is still thick in many MLCCs. In this study, we used small grain glass frit to embody thin film and highly densification in the end termination by improve sintering driving force with well-dispersion and rising surface energy. Pastes were fabricated using size changed glass frit, such as 0.1 ${\mu}m$, 0.5 ${\mu}m$, 1.0 ${\mu}m$, 4.0 ${\mu}m$. Fabricated pastes were applied 05A475KQ5 chip and fired various sintering temperatures to analyze sintering behavior of pastes. Consequently, small glass frit used pastes have many merits than larger, such as well-dispersion, improve cornercoverage and surface roughness, possibility of low temperature sintering. However, we confirmed that small glass frit used pastes have narrow sintering window by rapid completion of sintering densification.