• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.2
• /
• pp.92-97
• /
• 2011

Landfill is the main treatment method for bottom-ash because it has not only an irregular particle size and ingredients but also not proper recycling treatment. The aim of this study is to raise recycling rate of bottom-ash(nonplasticity pulverulent) and for the purpose of alternatives of clay to investigate the properties of Bottom-ash (B/A)-Hard Clay (H/C) bodies with controlled interfacial chemistry properties. After investigating the sedimentation height of suspensions with controlled pH, it was discovered that there was no hetero-polar aggregation for mixed slips because hard clay and bottom-ash had similar interfacial chemistry properties. Also, bulk density, water absorption, and microstructure properties of each pellet was observed that made by silp casting method and manufactured at $50^{\circ}C$ intervals between $1000{\sim}1250^{\circ}C$. As a result, dispersed slip of clay and bottom ash are possible for slip casting and plastic forming process because they exhibit Bingham plastic behavior. Products that made by slip with dispersed clay and bottom ash are not only suitable for KS L 4201 and KS L 1001 at $1250^{\circ}C$ but it is also possible to apply for ceramic and sanitary ware because specific gravity was about 15 % lighter than general ceramic materials.

• The Korean Journal of Ceramics
• /
• v.6 no.2
• /
• pp.100-102
• /
• 2000

Co fine particles were dispersed in Au metal and $AlO_x$ amorphous matrices by vacuum evaporation and rf-sputtering, respectively, thus forming granular composite films having chemical compositions of $Co_{0.59}-Au_{0.41}$ and $Co_{0.52}/(AlO_x$)_{0.48}$. The films were annealed at 200~$500^{\circ}C$ to increase the size of the Co particles, from 30$\AA$ to 180$\AA$ in the Au matrix and 40$\AA$ to 180$\AA$ in the $AlO_x$ matrix, as revealed by X-ray diffraction analysis. The Co metal in as-deposited films have saturation magnetization equivalent to that of bulk Co, which is unchanged by the annealing, showing that the Co metal is not oxidized by the annealing. Magneto-optical Kerr rotation measured at $\lambda$=400-900nm for the $Co_{0.59}-Au_{0.41}$ film as deposited is larger than that calculated for the composition. The rotation increases as the film is annealed at $200^{\circ}C$ and $300^{\circ}C$, approaching to that of bulk Co. The Kerr rotation for the $Co_{0.52}-(AlO_x)_{0.48}$ film as deposited is smaller than that calculated for the composition based on Bruggeman effective medium theory. However, the rotation increases much, exceeding the rotation of the bulk Co as annealed at $300^{\circ}C$ and $400^{\circ}C$. As a possible origin of the marked magneto-optical enhancement a weak localization of light in granular structure is suggested.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.4
• /
• pp.103-111
• /
• 2012

One of the basic physical properties of the hardened cement paste, the rigidity, is deteriorated during concrete matrix forming, depending on the replacement rate of the crushed stone powder, and due to drying shrinkage. Therefore, the concrete containing crushed stone powder has been limitedly used as non-structural construction material. To improve these disadvantages, a hydrothermal reaction employing method can be considered. High-temperature and high-pressure water is involved in the hydrothermal reaction in the mixing with specific materials. The rigidity improving mechanism is related to the synthesis of calcium silicate. The calcium silicate is produced through reaction between calcium compounds and the silicic acid. Various kinds of calcium silicate can be produced depending on the CaO/$SiO_2$ mole ratio, the temperature of the hydrothermal synthesis, the pressure, and the reaction time. The product of the synthesis mechanism, tobermorite crystal, plays a pivotal role for the rigidity reinforcement. The crushed stone powder, analyzed in this study, contains 50 to 60% of $SiO_2$ and 10 to 20% $Al_2O_3$. The composite rate is appropriate to create the tobermorite crystal through formation of hardened cement matrix under the hydrothermal synthetic conditions and with the CaO in the cement. Moreover, further reinforcement was promoted using the property of material under the identical density through promoting the formation of tobermorite crystal.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.27 no.6
• /
• pp.491-497
• /
• 2001

Polymethylmethacrylate(PMMA) is currently commonly used material for the reconstruction of bone defects and fixation of joint prosthetics following congenital and acquired causes. Although PMMA has widespread use, it does not possess the ideal mechanical characteristics with osteoconductivity and osteoinductivity required. In order to overcome these problem, addition of bovine bone drived defatting demineralized bone(BDB) powders to a PMMA bone cement was done for improvement of physical property and bone forming characteristics of composite. In order to investigate the influence of BDB reinforcement on the PMMA, we measured physical property of compressive, tensile, flexural strength, and scanning electron microscopic examinations. The results were obtained as follows: 1. The PMMA forms a solid cellular matrix with open cells about $100{\mu}m$ in variable size and incorporating BDB. BDB aggregates inside the cells form a porous network that is accessible from the outer surface. 2. The physical properties were compressive strength of mean $22.74{\pm}1.69MPa$, tensile strength of mean $22.74{\pm}1.69MPa$, flexural strength of mean $77.53{\pm}6.93MPa$. Scanning electron microscopic examinations were revealed that there was DBD particles form a highly porous agglomerates. BDB can be added PMMA in the form of dried powders, the composites are applicable as bone substitutes. BDB and PMMA mixture is shown to produce a class of composites that due to their microstructure and improved mechanical properties may be suitable for application as bone subsitutes. The mechanical and material properties of the BDB-PMMA bone substitute composites are competitive with those properties of a porous ceramic matrix of other hydroxyapatite and with those of natural bones.

• Journal of Conservation Science
• /
• v.31 no.1
• /
• pp.37-46
• /
• 2015

In the case of adhesives & restoration agents currently being used for the preservation treatment of ceramics and earthenware, epoxy type, cellulose type and cellulose type are mainly being used. However, they are showing various problems such as re-detachment from severe contraction, color change from yellowing, work inconvenience of staining on tools and hand during usage and irreversibility. For the purpose of solving the issues of yellowing and irreversibility of epoxy resin being used to restore ceramics, urethane synthetic resin with low yellowing excellent reversibility has been developed in this study. The adhesive strength of urethane resin that has been developed has excellent properties with 2.07MPa for undiluted solution, which is 1.5 times higher than that of existing material EPO-$TEK301^{(R)}$ 1.21MPa. The result of workability measurement showed that the wear rate of urethane resin (in Talc 50wt%) was 1.09%, which was somewhat higher than that of existing material Quick $Wood^{(R)}$ (1.02%). In addition, its wear rate is two times higher than that of $EPO-TEK301^{(R)}$ (0.41%) and $L30^{(R)}$ (0.39%), thereby showing an advantage in its forming process compared to existing materials. As for the advantage of urethane resin of reversibility experiment, 12 hours after acetone, ethyl alcohol deposition, urethane resin and filler talc were dissolved 100% while showing powdering phenomenon. Compared to 0% reversibility of existing epoxy resin, it has much superior reversibility. The result of UV rays experiment to evaluate its durability showed that ${\Delta}E^*ab$ color change value based on undiluted solution of urethane resin was 2.76 before & after UV rays exposure, which was a decrease by about 7-20 times compared to that of existing resin, thereby minimizing the issue of heterogeneity.