• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1332-1336
• /
• 2005

It could make the LIghtweight Piezoelectric Composite Actuator (LIPCA) damageable by the cyclic large deformation. If the progressive microvoid coalescence of LIPCA interlaminar took place, the decrease of the stiffness and the weakness of stress transmission and fiber bridging effect would make the fatigue characteristics worse suddenly. Therefore, it is required to study the variation of fatigue behavior and interlaminar condition in LIPCA under resonant frequencies. These studies such as the changeable fatigue phase and interlaminar behavior of LIPCA affected by the resonant frequencies should be carried out due to the strong anisotropy of CFRP layer. Hence, these studies are as follows. 1) The residual stresses distribution of interlaminar in LIPCA using the Classical Lamination Theory (CLT). 2) Comparative analysis of interlaminar behavior for the intact LIPCA versus LIPCA containing an artificial delamination during resonant frequency.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.66-67
• /
• 2005

In this study, in order to develop multilayer piezoelectric actuator, PMN-PNN-PZT ceramics were fabricated using $Li_2CO_3-Na_2CO_3$ as sintering aids and their piezoelectric and dielectric characteristics were investigated with the function of PNN substitution. With increasing PNN substitution, dielectric constant(${\varepsilon}r$), electromechanical coupling factor(kp), and piezoelectric d constant($d_{33}$) were increased at 10~12[mol%] PNN substitution and then decreased at all sintering temperature. With increasing PNN substitution, phase changed from tetragonal to rhombohedral at [10~12mol%] PNN substitution. At the 12[mol%] PNN substituted PMN-PZT composition ceramic sintered at 950[$^{\circ}C$], density, ${\varepsilon}r$, kp, $d_{33}$ and Qm showed the optimum value of 7.79[$g/cm^3$], 1160, 0.599, 419[pC/N) and 894, respectively for multilayer piezoelectric actuator application.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1275_1276
• /
• 2009

Micropump is very useful component in micro/nano fluidics and bioMEMS applications. Using the flexural vibration mode of PZT bar, a piezopump is successfully made. The PZT bar is polarized with thickness direction. The proposed structure for the piezo-pump consists of an input and an output port, piezoelectric ceramic actuator, actuator support, diaphragm. The traveling flexural wave along the bar is obtained by dividing two standing waves which are temporally and spatially phase shifted by 90 degrees from each other. Fluid is drawn into a forming chamber, eventually the forming chamber closes trapping the fluid therein.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.198-203
• /
• 2002

A fuzzy logic controller design technique is proposed to apply for the control of flexible system under irregular disturbance. The fuzzy rules of $\ulcorner$Mode Selecting Fuzzy Controller$\lrcorner$ are constructed using displacement, velocity information and modal characteristics of the system. The frequency information of flexible system is picked up from $\ulcorner$Mode Selecting Unit$\lrcorner$ based on Fast-Fourier transform algorithm. Experiment is conducted to verify the proposed theoretical approach, Piezo ceramic and laser accelerometer are used as actuator and sensor in the experiments respectively

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.41-44
• /
• 1998

(1-X)LTC-XHTC composites were manufactured with the variation of X in the range of 0.3 $\leq$X $\leq$0.6 and its dielectric properties were investigated. Here, LTC and HTC are PZN-BT-PT -based ceramics with quire temperature(Tc) of 100。 C-3$0^{\circ}C$, respectively. 0.6HTC-0.4LTC composite ceramics show excellent values of $\Delta$$\varepsilon$$_{r}$/$\varepsilon$[%] which were -7.1% at -2$0^{\circ}C$ and -12% at 5$0^{\circ}C$, respectively. It is thought that composite ceramics with above results can be applied to electrostrictive actuator, high voltage ceramic capacitor etc.mic capacitor etc.r etc.c.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.228-232
• /
• 2004

This paper is to identify the position of random disturbance on flexible dynamic system, and the position of the piezo ceramic actuator 0 minimize tip response. Correlation of the output signals from each parts on flexible system is used to identify the position of random disturbance. Except the correlation with an output signal from the position of random disturbance, other correlations have time delay. This is a base idea to identify the position on this study.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.397-398
• /
• 2006

The advanced piezoelectric ceramic composite actuator, which is called LIPCA with the FRP and the optimization of the laminate configuration, was performed to maximize the stress transfer and the fiber bridging effect. This study evaluated the effect of variable electric fields on the PZT characteristic, laminate configuration and fatigue characteristics under the resonance frequency, which meant the largest performance range and the changes of its interlaminar phase were also evaluated by stages. In conclusions, Comparing with the fatigue lift of intact LIPCA, the fatigue life of LIPCA embedded by the artificial delamination was decreased up to 50%. The micro void growth and the coalescence of epoxy were actively made at the interlaminar phase subject to the large tensile stress.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.249-250
• /
• 2006

Recently FPD(Flat Panel Display) is used in various field to display enormous information. So cutting technique of flat panel display is needed for producing variety display merchandises. In present, cutting methods of flat panel glass includes breaking process. But this process occurs many glass particles. This glass particles are directly related badness of merchandise and falling productivity. In this paper, to cut front substrate glass of LCD and to get optimized cutting condition are tried fur eliminating breaking process with developed glass cutting machine using a Piezoelectric ceramics actuator. It is known that the vibration of Piezoelectric Ceramic have effect in crack proceeding through the analysis of fracture section.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.22.5-22
• /
• 2001

Robust control of a GFR composite beam with a distributed PVDF sensor and piezo-ceramic actuator is presented En this paper. Modal analysis method and modal coordinates are introduced to obtain the state educations of the structural system. 1st and 2nd natural frequencies are considered In the modeling, because robust control theory which is robustness to structured uncertainty is adopted to suppress the vibration. If the controllers designed by H$\^$$\infty$/ theory do not satisfy control performance, it is improved by ${\mu}$-synthesis method with D-K Iteration so that the ${\mu}$-controller based on the structured singular value satisfies the nominal performance and robust performance.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.329-329
• /
• 2010

적층 액츄에이터는 우수한 압전특성 및 그 재료가 가진 고유한 특성 때문에 최근 이동통신 단말기용 햅틱 소자 및 PC 와 그 주변기기로 수요가 폭발적으로 증대되고 있으며, 향후에도 CATV 네트워크와 무선통신기기를 비롯한 디지털 통신분야로 응용분야가 확대되리라 예상된다. 적층 액츄에이터에서 발생되는 에너지는 세라믹 그린시트 두께와 전극 면적에 비례하여 변위 및 응력이 증가하게 되므로 고적층형에 대한 필요성이 증대되고 있다. 이러한 고적층 액츄에이터의 경우 소성과정에 서 warpage 및 de-lamination 같은 결함이 발생하기 쉬우므로 그린시트의 균일성 및 전극과의 matching성 확보가 중요한 요소이다. 본 연구에서는 슬러리의 분산성과 시트 내 유기물 함량 최적화 실험을 진행하여 적층 액츄에이터용 그린시트를 최적화 한 후 공정 적용성 및 저온소성 전극인 Ag-Pd 전극과의 매칭성을 확보하고자 하였다. 이러한 후막공정 기술 개선을 통해 적층 액츄에이터를 제조하여 압전 특성을 측정하였다.