• 한국안전학회지
• /
• 제30권4호
• /
• pp.168-173
• /
• 2015

A steam generator tubing is one of the main pressure boundary of the reactor coolant system in the nuclear power plants. Structural integrity refers to maintaining adequate margins against failure of the tubing. Burst pressure of a tube at tube support plate can be higher than that for a free-span tube because failure behaviors could be interfered from the tube support plate. Alternative repair criteria for out-diameter stress corrosion cracking indications in tubes to the drilled type tube support plate were developed, however, there are very limited information to the eggcrate type tube support plate. This paper discussed reinforcement effect of steam generator tube burst pressure with axial out-diameter stress corrosion cracking within an eggcrate type tube support plate. A series of tube burst tests were performed under the room temperature and it was found out that there is no significant but marginal effects.

• Geomechanics and Engineering
• /
• 제34권6호
• /
• pp.637-648
• /
• 2023

When an earth pressure balance (EPB) shield machine bores a tunnel in gravelly sand stratum, the excavated natural soil is normally transformed using foam and water to reduce cutter wear and the risk of direct muck squeezing out of the screw conveyor (i.e., muck spewing). Understanding the undrained shear behavior of conditioned soils under pressure is a potential perspective for optimizing the earth pressure balance shield tunnelling strategies. Owing to the unconventional properties of conditioned soil, a pressurized vane shear apparatus was utilized to investigate the undrained shear behavior of foam-conditioned gravelly sands under normal pressure. The results showed that the shear stress-displacement curves exhibited strain-softening behavior only when the initial void ratio (e₀) of the foam-conditioned sand was less than the maximum void ratio (e_max) of the unconditioned sand. The peak and residual strength increased with an increase in normal pressure and a decrease in foam injection ratio. A unique relation between the void ratio and the shear strength in the residual stage was observed in the e-ln(τ) space. When e₀ was greater than e_max, the fluid-like specimens had quite low strengths. Besides, the stick-slip behavior, characterized by the variation coefficient of measured shear stress in the residual stage, was more evident under lower pressure but it appeared to be independent of the foam injection. A comparison between the results of pressurized vane shear tests and those of slump tests indicated that the slump test has its limitations to characterize the chamber muck fluidity and build the optimal conditioning parameters.

• Tribology and Lubricants
• /
• 제19권2호
• /
• pp.85-93
• /
• 2003

In this study, a multigrid multi-integration method has been used to solve the steady-state, elastohydrodynamic lubrication (EHL) point contact problem of a ball joint mechanism used in small reciprocating compressors. Pressure and film thickness profiles have been calculated at minimum and maximum Moes M parameter conditions during one revolution of crankshaft. The effects of various lubricant viscosities, loads, ball velocities, elastic modulli, and radii of curvature on the calculated pressure distribution and film thicknesses have been investigated. The results indicate that the viscosity of lubricant, the sliding velocity of ball, and the reduced radius of curvature have considerable effects on the minimum and central film thicknesses. Solutions obtained with the multigrid analysis are compared with results calculated according to the Hamrock ＆ Dowson relations for the minimum and central film thicknesses.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.197-198
• /
• 2006

The high pressure compaction without internal lubricant and the high green density even with the pore free density were achieved by the newly developed die wall lubricant for warm compaction. This developed die wall lubricated warm compaction followed by high temperature sintering resulted in not only the superior mechanical property but also the low dimensional change. In this paper, the effects of increasing the green density on the sintered density, the dimensional change and the mechanical property are mainly discussed

• The Korean Journal of Physiology
• /
• 제3권2호
• /
• pp.25-31
• /
• 1969

Effects of graded increase of positive lung inflation upon heart rates and arterial blood pressure were observed in the anesthetized dogs to analyze the mechanical and neural regulatory factor in response to the positive inflation of the lung. The results obtained were summarized as followings: 1) When the low grade of positive lung inflation was employed under the mild to moderate anesthesia, central venous pressure was linearly increased while heart rate was decreased. After bilateral vagotomy, central venous pressure was obviously increased while heart rate was constant. 2) When the high degree of positive lung inflation was employed, changes of central venous pressure and heart rate were not significant. 3) The low grade of intrapulmonary pressure increase caused reflex tachycardia in phase 2 and overshooting in phase 4 in response to the systemic arterial blood pressure change. 4) On the other hand, the high degree of intrapulmonary pressure increase caused paradoxical bradycardia in phase 2 and lack of overshooting in phase 4 in response to the systemic arterial blood pressure change. 5) It may be noted that the experimental model employed in the present study is a useful tool to evaluate and analyze the neural and mechanical regulatory factor in response to the graded increase of the positive lung inflation.

• Journal of Veterinary Science
• /
• 제21권4호
• /
• pp.67.1-67.11
• /
• 2020

Background: Tibial tuberosity transposition (TTT) causes caudalization of the patellar ligament insertion in canine medial patellar luxation, which can lead to increases in patellofemoral contact pressure. Objectives: The purpose of this study is to confirm the effect of patellofemoral contact mechanics after craniolateral and caudolateral transposition of tibial tuberosity in normal canine hindlimbs. Methods: Craniolateral and caudolateral transposition of tibial tuberosity was performed in 5 specimens, respectively. The pressure was measured in the specimen before TTT, and then in the same specimen after TTT. In this process, data was obtained in 10 specimens. The measurement results were output as visualization data through the manufacturer's software and numerical data through spreadsheet. Based on these 2 data and the anatomical structure of the patellofemoral joint (PFJ) surface, whole measurement area was analysed by dividing into medial, lateral and central area. Results: In craniolateralization of tibial tuberosity, total, medial, central contact pressure was decreased and lateral contact pressure was not statistically changed lateral contact pressure than normal PFJ. In caudolateralization of tibial tuberosity, total, lateral contact pressure was increased and medial contact pressure was not statistically changed than normal PFJ. Although not statistically significant changed, central contact pressure in caudolateralization of tibial tuberosity was increased in all 5 specimens. Conclusions: These results imply that traditional TTT, prone to caudal shift of patellar tendon, can increase retropatellar pressure may lead to various complications and diseases of the stifle joint.

• Wind and Structures
• /
• 제24권5호
• /
• pp.501-528
• /
• 2017

In this work, wind tunnel tests of pressure measurements are carried out to assess the global aerodynamic interference factors, the local wind pressure interference factors, and the local lift spectra of an square high-rise building interfered by an identical cross-sections but lower height building arranged in various relative positions. The results show that, when the interfering building is located in an area of oblique upstream, the RMS of the along-wind, across-wind, and torsional aerodynamic forces on the test building increase significantly, and when it is located to a side, the mean across-wind and torsional aerodynamic forces increase; In addition, when the interfering building is located upstream or staggered upstream, the mean wind pressures on the sheltered windward side turn form positive to negative and with a maximum absolute value of up to 1.75 times, and the fluctuating wind pressures on the sheltered windward side and leading edge of the side increase significantly with decreasing spacing ratio (up to a maximum of 3.5 times). When it is located to a side, the mean and fluctuating wind pressures on the leading edge of inner side are significantly increased. The three-dimensional flow around a slightly-shorter disturbing building has a great effect on the average and fluctuating wind pressures on the windward or cross-wind faces. When the disturbing building is near to the test building, the vortex shedding peak in the lift spectra decreases and there are no obvious signs of periodicity, however, the energies of the high frequency components undergo an obvious increase.

• Geomechanics and Engineering
• /
• 제6권5호
• /
• pp.503-515
• /
• 2014

On the basis of Hoek-Brown failure criterion, a numerical solution for the shape of collapsing block in the rectangular cavity subjected to seepage forces is obtained by upper bound theorem of limit analysis. The seepage forces obtained from the gradient of excess pore pressure distribution are taken as external loadings in the limit analysis, and the pore pressure is easily calculated with pore pressure coefficient. Thus the seepage force is incorporated into the upper bound analysis as a work rate of external force. The upper solution of the shape of collapsing block is derived by virtue of variational calculation. In order to verify the validity of the method proposed in the paper, the result when the pore pressure coefficient equals zero, and only hydrostatic pressure is taken into consideration, is compared with that of previous work. The results show good effectiveness in calculating the collapsing block shape subjected to seepage forces. The influence of parameters on the failure mechanisms is investigated.

• 한국연초학회지
• /
• 제27권2호
• /
• pp.201-206
• /
• 2005

In this work, we studied the effects of the moisture contents of cut tobacco on loose end of cigarettes. The loose end of the cigarette groups decreased with the increase of moisture contents of the cut tobacco and especially the loose end of A and C groups decreased to $31\%\;and\;52\%$ with the increase of $1\%$ moisture contents. $A-13.5\%\;and\;B-14.0\%\;and\; C-14.0\%$ moisture samples showed the increase of the weight ratio of cut tobacco over 1.4mm cut length but the decrease under 1.4mm cut length. We concluded that the main reasons were regarded to reduction of small fragment tobaccos caused by increase of moisture contents and exception of air-suction transport of tobaccos to cigarette making machine. In spite of the moisture increase of cut tobaccos under fixed EPD(encapsulated pressure drop), the hardness of Band C sample groups were maintained constantly except A group. This result means that under fixed EPD, the weight of cut tobacco in cigarette rods increases to compensate the reduction of pressure drop by moisture increase of cut tobaccos.

• Macromolecular Research
• /
• 제16권7호
• /
• pp.590-595
• /
• 2008

The pressure driven membrane process has been a breakthrough in the removal of pollutants from drinking water. These experiments examined the removal of chlorophenol compounds from water using low pressure membranes. The removal performance of the membranes was based primarily on size exclusion. Apart from size exclusion, the polarity and pKa of the compounds also influences the membrane performance. The molecular size and dipole moments of the respective molecules were calculated using a quantum chemical method. The rejection of pollutants also followed the same trend as salt rejection by the membranes.