• 한국해양공학회지
• /
• 제32권3호
• /
• pp.158-165
• /
• 2018

Generally, container ships contain cargo holds with cell guides that serve to increase the container loading and unloading efficiency, minimize the space loss, and fix containers during the voyage. This paper describes a new quality management system for the cell guides of container ships (the so-called Trim Cell Guide system). The main functions of this system are the trimming of the point cloud obtained using a 3D scanner and an inspection simulation for cell guide quality. In other words, the raw point cloud of cell guides after construction is measured using a 3D scanner. Here, the raw point cloud contains a lot of noise and unnecessary information. Using the GUI interface supported by the system, the raw point cloud can be trimmed. The trimmed point cloud is used in a simulation for cell guide quality inspection. The RANSAC (Random Sample Consensus) algorithm is used for the transverse section representation of a cell guide at a certain height and applied for the calculation of the intervals between the cell guides and container. When the container hits the cell guides during the inspection simulation, the container is rotated horizontally and checked again for a possible collision. It focuses on a system that can be simulated with the same inspection process as in a shipyard. For a practicality review, we compared the precision data gained from an inspection simulation with the measured data. As a result, it was confirmed that these values were within approximately ${\pm}2mm$.

• 한국수소및신에너지학회논문집
• /
• 제23권2호
• /
• pp.156-161
• /
• 2012

In case of commercializing of the hydrogen fuel cell vehicle, the suitable emergency response guide is necessary to prepare an accident. In order to suggest the suitable guide for the domestic affairs, the existing external guide about GM, Ford, Honda, and Hyundai was reviewed. The emergency response guides in CAFCP and main FC vehicle makers were included in the analysis. As the results, it was found that the design and make of vehicle for the domestic user are demanded in the emergency response and the guide is made with the shut-down manual picked out for the rescuer and repair man as well as user.

• 한국공작기계학회논문집
• /
• 제17권2호
• /
• pp.45-50
• /
• 2008

Molecular flows inside a guide block in the OLED(organic luminescent emitting device) deposition process have been simulated using DSMC(direct simulation Monte Carlo) method. Because the organic materials are evaporated under vacuum, molecules flow at a high Knudsen number of the free molecular regime, where the continuum mechanics is not valid. A guide block is designed as a part of the linear cell source to transport the evaporated materials to a deposition chamber, When solving the flows, the inlet boundary condition is proved to affect significantly the whole flow pattern. Thus, it is proposed that the pressure should be specified at the inlet. From the analysis of the density distributions at the nozzle exit of the guide block, it is shown that the longer nozzle can emit molecules more straightly. Finally, a nondimensionalized mass flow profile is obtained by numerical experiments, where various nozzle widths and inlet pressures are tested.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.371-375
• /
• 2001

The concept of a new linear motor that uses piezo-stack actuator is demonstrated. The working principle is far different from the conventional inchworm motor. This motor is based on the self-moving cell concept. The linear motor has three cells and each cell is constructed with one piezo-stack actuator and a shell structure. A cell train is constructed by connecting these cells and the cell train is fitted into a guide way with a proper interference. The cell train moves along the guide way, by activating each cell in succession. The moving motion of the motor is tested. Since this linear motor uses piezo-stack actuator with unified clamping cell, it can produce fast speed, high resolution and large push force.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.915-916
• /
• 2012

• 설비공학논문집
• /
• 제22권10호
• /
• pp.672-678
• /
• 2010

The purpose of this study is to develop a stacking guidance system (SGS) of containers in the mobile harbor (MH). A mobile harbor is a floating structure especially designed for loading and unloading containers from and to a large container ship. A novel stacking guidance system was proposed for unloading the container in an effective way against possible vibrations of the floating body. The guidance system works as an aid for loading containers with a wider opening for easier stacking of a container into a moving storage cell due to waves. In order to determine the most effective inclination angle of the cell-guide, this study performed the dynamic analysis of the SGS equipped in the MH subject to fluctuations of the sea. The motions of the guidance system and a container loaded were calculated using ADAMS. The simulation results of the contact force between the two rigid bodies showed that a desirable angle of the cell-guide should be around 20 degrees from the vertical. This proposed SGS can considerably reduce the loading and unloading time, and will enhance the performance of the MH.

• 한국정밀공학회지
• /
• 제22권3호
• /
• pp.93-100
• /
• 2005

The top and bottom nozzles of PWR fuel assembly are connected by guide thimbles and an instrumentation tube that are connected with spacer grids. The fuel rods are inserted into the each cell of spacer grids. The loads acting on the fuel assembly are transmitted to the guide thimbles through the flow plate of top nozzle The axial loads applied to the fuel assembly are not equally distributed among the guide thimble due to the geometry of the top nozzle flow plate and spacer grid. In this study, the load concentration factors for the $17\times17$ fuel assembly were calculated. The analytical model fur the calculation of the load concentration factor of top nozzle flow plate was developed using ANSYS 5.6. The finite element analyses were performed using the model composed of top nozzle, guide thimble, and spacer grid. And, the analysis results were compared with the test results.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.554-557
• /
• 1999

This paper represent about design of the controller for battery of Guide-Eye Sign Lamp with traffic auxiliary system for power supply using solar cell. Simulation is represents V-I and power characteristic by Mathematical & Design Center 6.3 & Qnet 2.1. This system is successfully operating with high clearness lights.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.111-111
• /
• 2012

In this talk, we represent a novel approach to investigating intra-nanorod surface plasmon coupling with control over block compositions. The multi-component rod-like nanostructures, which consist of optically active components (Au and Ag) and optically less active component (for example, Ni) in UV-vis-NIR spectral window, showed interesting optical response depending on each block length and the total length of the structure. By controlling the composition and relative lengths of the blocks that comprise these structures, we can tailor the overall optical properties. Depending on the relative fraction of Au and Ag blocks, the intensity of the transverse modes varied without noticeable peak shifts. However, the strong intraparticle surface plasmon coupling resulted in the collective appearance of longitudinal LSP modes, including higher-order modes. The experimental observations were confirmed by theoretical calculation, using a discrete dipole approximation method. In addition, we will briefly discuss how single nanorod solar cells can be synthesized by using by using electrochemical deposition and AAO hard templates.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2008년도 특별논문집
• /
• pp.29-32
• /
• 2008

Hinged cross bar which is fitted for buyer's special item in cell guide of container vessels has an advantage of efficiency on container loading. In this paper, the main focus is to confirm the structural adequacy of hinged cross bar supporting structure in cell guide under the considered loading condition for container vessel.