• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.192-197
• /
• 2003

Three-dimensional cavity flow is analyzed with the code by using unstructured grid. Incompressible Navier-Stokes equations are used as governing equations, and governing equations are discretized by Finite Volume Method. Artificial compressibility method, proposed by Chorin, and developed by Soh, is used for coupling a pressure and a velocity. Cell-centered scheme is adopted in the code, this has the effect of having denser grid than nodal scheme when the same grid is used. Weighted Averaging scheme is used for the value at a nodal point. Cavity flow is analyzed, and this computed results are compared with the results in the research report

• 한국전산유체공학회지
• /
• 제5권1호
• /
• pp.14-21
• /
• 2000

A method of two and three dimensional orthogonal grid generation with control of spacing by using the covariant Laplace equation is presented. An important feature of the methodology is its ability to control effectively the grid spacing especially near the boundaries still maintaining good orthogonality in whole field. The method is based on the concept of decomposition of the global transformation into consecutive transformation of an approximate conformal mapping and an auxiliary orthogonal mapping to have linear and uncoupled equations. Control of cell spacing is based on the concept of reference arc length, and orthogonal correction is peformed in the auxiliary domain. It is concluded that the methodology can successfully generate well controlled orthogonal grids around bodies of 2 and 3 dimensional configurations.

• 전기학회논문지
• /
• 제58권11호
• /
• pp.2175-2184
• /
• 2009

This paper describes operational analysis results of the DC micro-grid using detailed model of distributed generation. Detailed model of wind power generation, photo-voltaic generation, fuel-cell generation was implemented with the user-defined model of PSCAD/EMTDC software that is coded with C-language. The operation analysis was carried out using PSCAD/EMTDC software, in which the power circuit is implemented by built-in model and the controller is modelled by user-defined model that is also coded with C-language. Various simulation results confirm that the DC micro-grid can operate without any problem in both the interconnected mode and the islanded mode. The operation analysis result confirms that the DC micro-grid make it feasible to provide power to the load stably. And it can be utilize to develop the actual system design and building.

• 한국주조공학회지
• /
• 제43권6호
• /
• pp.302-309
• /
• 2023

일반적으로 주조품은 복잡한 형상을 가지고 있고, 한 제품 내에서 두께의 차이가 현저하게 나는 경우가 있어 시뮬레이션을 위한 격자를 생성할 때 어려움이 있다. 주조 유동은 이상유동으로 수치해석을 할 때 공기와 용탕의 경계면을 추적해야하며 밀도차에 의한 압력장 계산에 많은 시간이 소요된다. 이와 같은 이유로 주조유동해석에는 직교격자가 주로 이용되어왔다. 그러나 직교격자는 형상을 제대로 표현하지 못한다. 곡면에서 나타나는 계단형상 격자로 인해 모멘텀 손실이 발생하고 이로 인해 용탕의 흐름이 달라질 수 있으며 결과적으로 잘못된 주조 방안 설계를 할 수 있다. 이를 피하기 위하여 직교격자계에서 형상을 좀 더 정확하게 표현하기 위하여 많은 수의 격자를 생성하여 해석을 한다. 또는 직교격자계에서 발생하는 문제를 수치적으로 보완하는 Cut Cell 방법을 적용하여 해석하는 방법이 있다. 본 연구에서는 직교격자계에서 주조유동해석을 할 때 격자수에 따른 해석결과와 Cut Cell 방법을 적용한 해석 결과를 비교하였다. 또한 주조공정별로 실제제품을 주조유동해석을 하고 공정별로 Cut Cell 방법을 적용한 결과를 고찰하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 춘계 학술대회논문집
• /
• pp.177-181
• /
• 2007

Present study examines the numerical issues of cell structure simulation for various regimes of detonation phenomena ranging from weakly unstable to highly unstable detonations. Inviscid fluid dynamics equations with $variable-{\gamma}$ formulation and one-step Arrhenius reaction model are solved by a MUSCL-type TVD scheme and 4th order accurate Runge-Kutta time integration scheme. A series of numerical studies are carried out for the different regimes of the detonation phenomena to investigate the computational requirements for the simulation of the detonation wave cell structure by varying the reaction constants and grid resolutions. The computational results are investigated by comparing the solution of steady ZND structure to draw out the minimum grid resolutions and the size of the computational domain for the capturing cell structures of the different regimes of the detonation phenomena.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.202-205
• /
• 1997

We investigated grain boundary effect for terrestrial applications of solar cell\ulcorner with low cost, large area, and high efficiency. Grain boundaries are known as potential barriers and recombination centers for the photo-generated charge carriers, which make it difficult to achieve a high efficiency cell. To reduce these effects of grain boundaries, we investigated various influencing factors such as thermal treatments, various grid patterns, selective wet etchings for grain boundaries, buried contact metallizations along grain boundaries, and use of metallic thin films. From the various grid patterns we learned that the series resistance of solar cell reduced open circuit voltage and consequently decreased the cell efficiency. This paper describes the effect of various grid patterns and the employment of metallic thin films for a top electrode.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제13권2호
• /
• pp.635-656
• /
• 2019

In this paper, we investigate the degrees of freedom (DoF) of a multi-cell multi-user multiple-input multiple-output (MIMO) interference broadcast channel (IBC) with non-cooperation distributed base stations (BS), where each BS serves users of its corresponding cell. When all BSs simultaneously transmit their own signals over the same frequency band in the MIMO IBC, the edge users in each cell will suffer the inter-cell interference (ICI) and inter-user interference (IUI) signals. In order to eliminate the ICI and IUI signals, a distributed space time interference alignment (DSTIA) approach is proposed where each BS has only limited access to distributed moderately-delay channel state information at the transmitter (CSIT). It is shown that the DSTIA scheme can obtain the appreciate DoF gains. In addition, the DoF upper bound is asymptotically achievable as the number of antenna at each BS increases. It is shown that the DSTIA method can get DoF gains over other interference alignment schemes with delayed CSIT in literature. Moreover, the DSTIA method can attain higher DoFs than the IA schemes with global CSIT for certain antenna configurations.

• 한국동물번식학회:학술대회논문집
• /
• 한국동물번식학회 2001년도 춘계학술발표대회
• /
• pp.76-76
• /
• 2001

The objective of this study was to optimize the vitrification method of in vitro produced bovine embryos. Thus, in vitro produced embryos at 8 cell, morula and blastocyst stages were vitrified on electron microscope grids (EM grids) or in open pulled straws (OPS) with EG5.5 (5.5 M ethylene glycol, 1.0 M sucrose and 10% FBS in m-DPBS medium) freezing solution and their survival rates after thawing were compared. The embryos on EM grids or in OPS were briefly exposed to EG5.5 freezing solution and plunged directly into liquid nitrogen within 30 to 35 sec. Post-thawed embryos were serially diluted in 0.5, 0.25 and 0.125 M sucrose in m-DPBS, each for 1 min, and then cultured in CRI aa medium supplemented with 10% FBS. Embryonic survival rate was assessed as re-expanded and hatched rates of those embryos after warming. The rates of re-expansion embryos did not significantly different between EM grid (8 cell: 42.10%, morula: 66.66% and blastocyst: 77.08%) and OPS (8 cell: 47.36%, morula: 61.90% and blastocyst: 83.33%) methods. In addition, the hatched rates in EM grid (8 cell: 31.57%, morula: 57.14% and blastocyst: 72.91%) were similar to those in OPS (8 cell. 34.21%, morula: 50.00% and Blastocyst: 77.08%). Interestingly, even at the same blastocyst stage, the in vitro survival of day 7 embryos (EM grid: 79.48 and OPS: 87.18%) was higher than those of day 8 embryos (EM grid: 72.10 and OPS: 82.06%). The total cell number of blastocyst developed in vitro after vitrification was examined with Hoechst 33342 staining to compare the embryo quality among different treatment groups. The total cell number of blastocyst was not significantly different between vitrified groups (EM grid: 162.4$\pm$8.0 and OPS: 158.4$\pm$7.1) and unvitrified control (168.0$\pm$5.6). These results indicate that both vitrification containers can provide the high rate of embryo survival. Moreover, the OPS container may not need a cap to protect the container from floating after immersion in L$N_2$. Therefore, this study suggest that bovine embryos can be cryopreserved easily, effectively and successfully by vitrification method using EM grid or OPS with EG5.5 freezing solution. In the future, the Pregnancy rate would be investigated after transfer of our vitrified embryos into the appropriated recipients.

• 한국농림기상학회지
• /
• 제6권3호
• /
• pp.149-163
• /
• 2004

Evapotranspiration (ET) is a critical component of the hydrologic cycle which influences economic activities as well as the natural ecosystem. While there have been numerous studies on ET estimation for homogeneous areas using point measurements of meteorological variables, monitoring of spatial ET has not been possible at landscape - or watershed - scales. We propose a site-specific application of the land surface model, which is enabled by spatially interpolated input data at the desired resolution. Gyunggi Province of South Korea was divided into a regular grid of 10 million cells with 30m spacing and hourly temperature, humidity, wind, precipitation and solar irradiance were estimated for each grid cell by spatial interpolation of synoptic weather data. Topoclimatology models were used to accommodate effects of topography in a spatial interpolation procedure, including cold air drainage on nocturnal temperature and solar irradiance on daytime temperature. Satellite remote sensing data were used to classify the vegetation type of each grid cell, and corresponding spatial attributes including soil texture, canopy structure, and phenological features were identified. All data were fed into a standalone version of SiB2(Simple Biosphere Model 2) to simulate latent heat flux at each grid cell. A computer program was written for data management in the cell - based SiB2 operation such as extracting input data for SiB2 from grid matrices and recombining the output data back to the grid format. ET estimates at selected grid cells were validated against the actual measurement of latent heat fluxes by eddy covariance measurement. We applied this system to obtain the spatial ET of the study area on a continuous basis for the 2001-2003 period. The results showed a strong feasibility of using spatial - data driven land surface models for operational monitoring of regional ET.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.518-522
• /
• 2011

Cartesian grid system has mainly been used in the casting simulation even though it does not nicely represent sloped and curved surfaces. These distorted boundaries cause several problems. A special treatment is necessary to clear these problems. A cut cell method on Cartesian grids has been developed to simulate three-dimensional mold filling Cut cells at a cast-mold interface are generated on Cartesian grids. Governing equations were computed using volume and areas of cast at cut cells. In this paper, we propose a new method that can consider the cutting cells which are cut by casting and mold based on the patial cell treatment (PCT). This method provides a better representation of geometry surface and will be used in the computation of velocities that are defined on the cell boundaries in the Cartesian gird system. Various test examples for several casting process were computed and validated. The analysis results of more accurate fluid flow pattern and less momentum loss owing to the stepped boundaries in the Cartesian grid system were confirmed. We can know the momentum energy at the cut cell is conserved by using the cut cell method. By using the cut cell method. performance of computation gets better because of reducing the whole number of meshes.