• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.6
• /
• pp.765-772
• /
• 2011

In this research, the fuel cell system model capable of generating codes in real time was developed to construct of a HIL (Hardware-In-the-Loop) for a SOFC-powered ship. Moreover, the effects of the distribution of the exhaust gas flow rates in a stack, the flow rates of fuels and temperature of air supplied on the temperature characteristics of fuels supplied to the cathode and the anode, the output power of the stack and system efficiency are examined to minimize the temperature difference between fuels supplied to the stack used in a 500kW SOFC system using methane as a fuel. As a result, the temperatures of fuels supplied to the cathode and the anode maintain at 830K when the opening factor of three-way valve located at outlet of turbine is 0.839. Also the process for optimization of methane flow rate considering the fuel cell stack and system efficiency is required to increase the temperatures of fuels supplied to the stack.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.7
• /
• pp.627-633
• /
• 2011

Performance of a hydrogen generator for a fuel cell unmanned aircraft was evaluated as the change of temperature environment. Sodium borohydride ($NaBH_4$) was used as a hydrogen source due to its high hydrogen content and good storability. The hydrogen gas was generated by the hydrolysis reaction using a catalytic reactor. Reaction chambers were set up with the range of temperatures from -20 to $60^{\circ}C$. The hydrogen generation rate and temperatures changes of reactor and separator were measured at the $NaBH_4$ concentrations of 20 and 25wt.%. As a result, the hydrogen generation rate was decreased as the repeated reaction cycles. It showed that the hydrogen generation rate was stable at low temperature, while at high temperature the hydrogen generation rate was rapidly decreased. The performance degradation was mainly caused by the catalyst loss and $NaBO_2$ deposition on the catalyst surface.

• Asian Pacific Journal of Cancer Prevention
• /
• v.13 no.3
• /
• pp.1025-1029
• /
• 2012

Objective: To determine the killing effects on extracorporeal HepG2 cells under different temperatures, pressures of permeability and lengths of treatment time. Method: According to different temperatures, pressures of permeability and lengths of treating time, extracorporeal HepG2 cells of human hepatoma cell-line were grouped to 80 groups. Cell index (CI) as the measurement of killing effect were calculated by monotetrazolium (MTT) methods, i.e., CI =1- (the OD value in treated group - the OD value in blank control group) / (mean of untreated control group - mean of blank control group). According to the factorial design, data were fed into SPSS 10.0 and analyzed by three-way ANOVA (analysis of variance). Result: Temperature, pressure of permeability and length of treating time all had effects on the CI (cell index) level. Length of treating time was the most influential factor of the three. Additionally, any two of them all had statistically significant interactive effects on the CI level. When treated for 5-30 min, destilled water at $46^{\circ}C$ stably generated the highest CI. Conclusion: The "$46^{\circ}C$-destilled water-60 min" was considered as the optimal combination of conditions which lead to highest CI. We suggest exerting celiac lavage for 15 min with stilled water at $40^{\circ}C-43^{\circ}C$ in surgical practice as a hyperthermia treatment to achieve ideal killing effects on free cancer cells, which is feasible, practical, and clinically effective.

• Journal of Microbiology and Biotechnology
• /
• v.8 no.3
• /
• pp.237-244
• /
• 1998

A study was carried out to elucidate the relation between the production of flavonol glycosides and the change of phenylalanine ammonia-lyase activity in cell suspension cultures of Ginkgo biloba by the unassisted and synergistic effects of various factors. The quercetin production showed a mixed-growth-associated pattern in cell suspension cultures. Fluorescent light and UV radiation increased phenylalanine ammonia-lyase (PAL) activity, and resulted in the increase of the production of quercetin and kaempferol ten- and four-fold, respectively, as compared to that obtained in the normal culture condition. The cell growth of Ginkgo biloba was enhanced .at higher temperatures whereas the quercetin production was at its maximum at low temperatures. Moreover, the quercetin production was increased by temperature change during the culture period. In particular, the quercetin production was at the highest level when the culture temperature was elevated from $10^{\circ}C\;to\;30^{\circ}C$. The addition of phenylalanine as a precursor in the culture medium stimulated an 8-fold increase in the production of quercetin; the addition of naringenin caused a l0-fold increase. The quercetin production was also greatly increased by feeding enzyme cofactors such as 2-ketoglutarate and ascorbic acid in the culture medium, but specific PAL activity was not increased except with phenylalanine feeding. The synergistic effect of UV radiation and naringenin feeding was observed, resulting in the increase of flavonol glycoside production at a rate higher than in any other case investigated.

• Journal of Sensor Science and Technology
• /
• v.25 no.5
• /
• pp.377-381
• /
• 2016

NDIR $CO_2$ gas sensor was prototyped with ASIC implemented thermopile sensor which included temperature sensor and White-Cell structure in this paper. The temperature dependency of dual infrared sensors ($CO_2$ and reference IR sensors) has been characterized and their output voltage ratios according to the temperature and gas concentration were presented in this paper for achieving temperature compensation algorithm. The initial output voltages of NDIR $CO_2$ gas and reference IR sensors showed $3^{rd}$ order polynomial and linear output voltages according to the variation of ambient temperatures from 253 K to 333 K, respectively. The output voltages of temperature sensor presented a linear dependency according to the ambient temperature and could be described with V(T) = -3.0069+0.0145T(V). The characteristics of output voltage ratios could be modeled with five parameters which are dependent upon the ambient temperatures and gas concentration. The estimated $CO_2$ concentrations showed relatively high error below 300 ppm (maximum 572 % at 7 ppm $CO_2$ concentration), however, as the concentration increased from 500 ppm to 2,000 ppm, the overall estimated errors of $CO_2$ concentrations were less than ${\pm}10%$ in this research.

• Transactions of the Korean hydrogen and new energy society
• /
• v.19 no.5
• /
• pp.403-409
• /
• 2008

Polymer electrolyte membrane fuel cell (PEMFC) is very interesting power source due to high power density, simple construction and operation at low temperature. But it has problems such as high cost, improvement of performance, effect of temperature and initial start at low temperature. These problems can be approached to be solved by using experiment and mathematical method which are general principles for analysis and optimization of control system for heat and hydrogen detecting management. In this paper, insulation vessel and control system for stable operation of fuel cell at low temperature were developed for experiment. The constant temperature capability and the heating time at sub-zero temperatures with insulation control system were studied by using a heating bar of 60W class. PEMFC stack which was made by 4 cells with $50\;mc^2$ active area in each cell is a thermal source. Times which take to reach constant temperature by the state of insulation vacuum were measured at variable environment temperatures. The test was performed at two conditions: heating mode and cooling mode. Constant temperature capability was better at lower environment temperature and vacuum pressure. The results of this experiment could be used as basis data about stable operation of fuel cell stack in low temperature zone.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.6
• /
• pp.34-40
• /
• 1985

Characteristics of GaAE epilayers grown on (100) CaAs wa(tors by molecular beam epitaxy (MBE) under various single crystal growing conditions were investigated. In fabrica-ting GaAs, epilayer by MBE, the most important factors are a substrate temperature(ts) and a flux density ratio (As/Ga). In this experiment, the substrate temperature was varied in the range of 48$0^{\circ}C$ to $650^{\circ}C$ and As and Ga cell temperatures were varied in the range of 218$^{\circ}C$ to 256$^{\circ}C$ and 876$^{\circ}C$ to 98$0^{\circ}C$, respectively. At the substrate temperature of 54$0^{\circ}C$, As cell temperature of 23$0^{\circ}C$, and Ga cell temperature of 91$0^{\circ}C$, the As/Ga ratio was 5"10, the surface morphology was most smooth . Investigation of As-stabilized surface by RHEED and of depth profile by SIM5 showed that As is less stable than Ga. Also, X-ray diffraction measurement revealed that single crystals of (400) and (200) were formed at the both sub-strate temperatures of 52$0^{\circ}C$ and 54$0^{\circ}C$.TEX>.

• Journal of Microbiology
• /
• v.42 no.3
• /
• pp.248-252
• /
• 2004

In order to identify the protein(s) secreted into culture medium by the sool-l/retl-l mutation of Saccharomyces cerevisiae, proteins from the culture medium of cells grown at permissive (28$^{\circ}C$) and non-permissive temperatures (37$^{\circ}C$), were analyzed. Comparison of protein bands separated by SDS-PAGE identified a prominent band of 47-kDa band from a mutant grown at 37$^{\circ}C$. N-terminal amino acid sequencing of this 47-kDa protein showed high identity with enolases 1 and 2. Western blot analysis revealed that most of the cell wall-bound enolase was released into the culture medium of the mutant grown at 37$^{\circ}C$, some of which were separated as those with lower molecular weights. Our results, presented here, indicate the impairment of cell wall enolase biogenesis and assembly by the sool-l/retl-l mutation of S. cerevisiae.

• Journal of the Korean Ceramic Society
• /
• v.42 no.12 s.283
• /
• pp.777-786
• /
• 2005

The Solid Oxide Fuel Cell (SOFC) is an electrochemical device to convert chemical energy of a fuel into electricity at temperatures from about 600 to $1000^{\circ}C$. The SOFC offers certain advantages over lower temperature fuel cells, notably its ability to use CO as a fuel rather than being poisoned by it, and high grade exhaust heat for combined heat and power, or combined cycle gas turbine applications. This paper reviews the operating principle, materials for different cell and stack components, cell designs, and applications of SOFCs. Among all designs of Solid Oxide Fuel Cells (SOFCs), the most progress has been achieved with the tubular design. However, the electrical resistance of tubular SOFCs is high, and specific power output $(W/cm^2)$ and volumetric power density $(W/cm^3)$ low. Planar SOFCs, in contrast, are capable of achieving very high power densities.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.3
• /
• pp.184-192
• /
• 2010

PEM fuel cell produces electric power, water and heat by the electrochemical reaction of hydrogen and oxygen. The heating value is dependent on the molar enthalpy of vaporization of product water and the performance loss. In this paper, the heating value of fuel cell stack has been studied under various stack operating temperatures to achieve more efficient heat management. A technology using the molar enthalpy of vaporization of product water is suggested to reduce heat-up time during start-up of a fuel cell vehicle.