• Composites Research
• /
• 제23권2호
• /
• pp.10-16
• /
• 2010

가압주조법으로 제조된 알루미나 섬유와 SiC 입자 혼합금속복합재료의 마찰특성을 조사하였다. 핀 형태의 마모 시험편은 전체 부피비 20%에 섬유와 입자의 서로 다른 비를 갖고 있다. 혼합금속복합재료의 윤활마모시험은 핀과 디스크 타입의 마모시험기를 사용하여 수행되었는데, 상온과 고온 $100^{\circ}C$와 $150^{\circ}C$.에서의 건식마찰특성을 각각 수행하였다. 마모면의 미시분석은 주사전자현미경(SEM)으로 조사하여 마찰특성과 마모거동을 분석하였다. 시험 결과 마모저항은 상온에서는 섬유와 같은 방향인 (PR) 방향에서는 SiC입자의 증가에 따라 향상되었다. 고온에서는 섬유와 수직한 방향(N)의 마모특성은 PR방향의 섬유가 마모면으로 전체적으로 쉽게 뽑히기 때문에 PR방향의 금속보합재료의 마모특성보다 우수하였다. 한편 마찰계수는 온도증가에 따라 감소하였다.

• Computers and Concrete
• /
• 제14권3호
• /
• pp.211-231
• /
• 2014

Prestressed hollow-core slabs (HCS) are widely used for modern lightweight precast floor structures because they are cost-efficient by reducing materials, and have excellent flexural strength and stiffness by using prestressing tendons, compared to reinforced concrete (RC) floor system. According to the recently revised ACI318-08, the web-shear capacity of HCS members exceeding 315 mm in depth without the minimum shear reinforcement should be reduced by half. It is, however, difficult to provide shear reinforcement in HCS members produced by the extrusion method due to their unique concrete casting methods, and thus, their shear design is significantly affected by the minimum shear reinforcement provision in ACI318-08. In this study, a large number of shear test data on HCS members has been collected and analyzed to examine their web-shear capacity with consideration on the minimum shear reinforcement requirement in ACI318-08. The analysis results indicates that the minimum shear reinforcement requirement for deep HCS members are too severe, and that the web-shear strength equation in ACI318-08 does not provide good estimation of shear strengths for HCS members. Thus, in this paper, a rational web-shear strength equation for HCS members was derived in a simple manner, which provides a consistent margin of safety on shear strength for the HCS members up to 500 mm deep. More shear test data would be required to apply the proposed shear strength equation for the HCS members over 500 mm in depth though.

• 한국세라믹학회지
• /
• 제35권2호
• /
• pp.163-171
• /
• 1998

Continuously contacting with camshaft the face of Valve Lifter made of cast iron brings about abnormal wear such as unfairwear or earlywear because it is heavily loaded in the valve train systems as the engine gets more powered. This abnormal wear becomes a defet namely over-clearance when the valve is lifting so that the fuel gas imperfectly combusted by unsuitable open or close aaction of the engine valve in the combustion chamber. The imperfect combustion in the end results in the major cause of air pollution and combustion chamber. The imperfectly combusted by unsuitable open or close action of the engine valve in the combustion chamber. The imperfect combustion in the end results in the major causes of air pollution and decrease of the engine output. Consequently to prevent this wear this study was to develop the valve lifter which is joined by brazing process with SCM435H and a tip by manufacturing the face as a superhardened which is joined by brazing process with SCM435H and a tip by manufacturing the face as a superhardened ceramics alloy which has high wear resistance. Having the excellent surface hardness with Hv1100-1200 the sintered body developed with superhardened alloy(WC) can endure the severe face loading in the valve train system. We experienced with various brazing alloys and obtained the excellent joining strength to the joint had 150MPa shear strength. Interface analysis and microstructure in a joint were examined through SEM & EDS Optical microscope. Also 2,500 hours high speed(3,000-4,000 rpm) and continuous (1step 12hr) engine dynamo testing was carried out to casting valve liter and ceramics-metal joint valve lifter so that the abnormal wears were compared and evaluated.

• 대한치과보철학회지
• /
• 제27권2호
• /
• pp.53-78
• /
• 1989

This study was taken to observe the changes of the residual stress in the alloy and to measure 3 dimensional distortions of the long span ceramo-metal bridge. The materials used in this study were Pors-on 4 (Pd-Ag alloy), and Ceramco and Vita VMK 68 powders. The residual stress of the alloy was measured on the six specimens (dia. 8m/m) by the X-ray diffraction stress analyzer according to the kind of ceramic powder and different measuring stages. And, for the measurement of the distortions, fifteen specimens of the anterior 8-unit ceramo-metal brige were fabricated and subjected to the 3-D coordinate measuring machine. Variables included the 2 kinds of a ceramic powder and the presence or absence of a splint bar at the cast metal framework. The measuring stages in both were after casting, after degassing and after glazing. The following conclusions were obtained : 1. The residual stress of the alloy showed increasing tendency for the tension by the ceramic fusing, but there was not significance. 2. The tendency of the distortions in the cast metal frameworks were decrease of the width, the anterior displacement and sagging. 3. The amount of the distortions at the degassing stage were greater than that at the ceramic fusing stage. 4. The splint bar was effective to control the distortion only at ceramic fusing stage. 5. The sagging distortion in the Ceramco firing were even through all measuring stages, but in the Vita firing, pronounced at degassing stage.

• The Journal of Advanced Prosthodontics
• /
• 제6권4호
• /
• pp.266-271
• /
• 2014

PURPOSE. The purpose of this study was to compare the fracture strength of the metal and the bond strength in metal-ceramic restorations produced by selective laser sintering (SLS) and by conventional casting (CAST). MATERIALS AND METHODS. Non-precious alloy (StarLoy C, DeguDent, Hanau, Germany) was used in CAST group and metal powder (SP2, EOS GmbH, Munich, Germany) in SLS group. Metal specimens in the form of sheets ($25.0{\times}3.0{\times}0.5mm$) were produced in accordance with ISO 9693:1999 standards (n=30). To measure the bond strength, ceramic was fired on a metal specimen and then three-point bending test was performed. In addition, the metal fracture strength was measured by continuing the application of the load. The values were statistically analyzed by performing independent t-tests (${\alpha}=.05$). RESULTS. The mean bond strength of the SLS group (50.60 MPa) was higher than that of the CAST group (46.29 MPa), but there was no statistically significant difference. The metal fracture strength of the SLS group (1087.2 MPa) was lower than that of the CAST group (2399.1 MPa), and this difference was statistically significant. CONCLUSION. In conclusion the balling phenomenon and the gap formation of the SLS process may increase the metal-ceramic bond strength.

• The Journal of Advanced Prosthodontics
• /
• 제9권4호
• /
• pp.239-243
• /
• 2017

PURPOSE. The purpose of this study is to compare single and three-unit metal frameworks that are produced by micro-stereolithography. MATERIALS AND METHODS. Silicone impressions of a selected molar and a premolar were used to make master abutments that were scanned into a stereolithography file. The file was processed with computer aided design software to create single and three-unit designs from which resin frameworks were created using micro-stereolithography. These resin frameworks were subjected to investment, burnout, and casting to fabricate single and three-unit metal ones that were measured under a digital microscope by using the silicone replica technique. The measurements were verified by means of the Mann-Whitney U test (${\alpha}=.05$). RESULTS. The marginal gap was $101.9{\pm}53.4{\mu}m$ for SM group and $104.3{\pm}62.9{\mu}m$ for TUM group. The measurement of non-pontics in a single metal framework was $93.6{\pm}43.9{\mu}m$, and that of non-pontics in a three-unit metal framework was $64.9{\pm}46.5{\mu}m$. The dimension of pontics in a single metal framework was $110.2{\pm}61.4{\mu}m$, and that of pontics in a three-unit metal framework was $143.7{\pm}51.8{\mu}m$. CONCLUSION. The marginal gap was smaller for the single metal framework than for the three-unit one, which requires further improvement before it can be used for clinical purposes.

• 대한기계학회논문집A
• /
• 제40권10호
• /
• pp.865-871
• /
• 2016

조직 공학에서는 전통적인 인공지지체 제작 방식인 가스 발포, 염 침출, 스폰지 복제 그리고 동결주조 법 등이 이용되고 있다. 하지만 다양한 공극 형태 및 크기를 가지고 있어서 세포 상호 작용 효과 및 충분한 기계적 특성에 한계가 있다. 그러나 열 용해 적층 법은 조직공학에서 폴리머 재료를 이용하여 다양한 3차원 인공지지체를 제작할 수 있는 가장 적절한 기술이다. 따라서 본 연구에서는 PCL 몰드를 제작하고 실리카와 알긴산 나트륨 염을 포함하는 세라믹 슬러리를 제조하여 몰드에 주입시켰으며, 1일 동안 자연 건조를 시켰다. 제작된 3차원 슬러리 몰드는 PCL 몰드의 제거 및 슬러리를 경화시키기 위해 $100^{\circ}C$의 오븐에서 2시간 열처리 되었고, 열처리 후에 $1100^{\circ}C$에서 소결되었다. 제작된 인공지지체는 주사전자현미경을 통해 관찰되었고, 압축 시험을 통해 알긴산 나트륨 염의 혼합량에 따른 인공지지체의 기계적 특성은 평가되었다.

• 한국응용과학기술학회지
• /
• 제29권1호
• /
• pp.13-18
• /
• 2012

금속 주조시 사용되는 탄소이형제를 카본블랙과 점증제 겸 알데하이드 화합물의 경화제로 사용될 수 있는 수용성 고분자인 잔탄검(X-gum), 카르복시메틸셀룰로오스(CMC)을 혼합하여 제조하였다. 이 때 카본블랙의 안정한 분산을 위하여 0.25 wt%의 X-gum 또는 1.0 wt%의 CMC가 적당하였다. 1.0 wt% 보다 낮은 농도의 CMC를 사용했을 경우 카본블랙이 매우 쉽게 층분리되었다. 유리판에 대한 부착력은 경화제와, 구르탈알데하이드 및 사슬연장제인 올리고당의 양에 비례하였으며. X-gum으로 제조된 탄소 이형제는 CMC를 이용해 제조된 것보다 유리에 대한 부착력이 우수하였다. 결과적으로 본 실험의 최적 조건에서 제조된 탄소이형제는 친환경적으로 주조시에 적용할 수 있을 것으로 판단된다.

• Composites Research
• /
• 제12권1호
• /
• pp.68-75
• /
• 1999

본 연구에서는 저속 충격에서 충격 속도에 따른 금속복합재료의 동적 거동을 연구하였다. 시험에 사용된 재료는 모재로 AC8A와 보강재로 알루미나($Al_2O_3$)와 탄소를 사용하였으며 용탕 주조법을 이용하여 금속복합재료를 제조하였다. 금속복합재료에는 15%의 부피분율을 가진 알루미나 예비성형체와 알루미나와 탄소를 각각 12%와 3% 사용한 혼합 에비성형체가 사용되었다. 제조된 금속복합재료는 인장 시험과 진동 시험을 통해 인장 강도와 탄성계수를 구하였으며, 저주파 여파기(low pass filter)와 계장화 충격 시험기를 이용하여 충격 속도에 따른 금속복합재료의 충격 거동을 연구하였다. 저주파 여파기를 이용함으로써 충격 속도에 관계없이 안정적인 실험치를 확보할 수 있었다. 충격 속도의 증가에 따라 모재와 금속복합재료의 충격에너지는 증가하였으나, 동적인성치는 일정한 값을 보였다. 충격 속도가 증가할수록 충격에너지 중 균열전파에너지의 향상이 두드러졌으며, 재료의 변형량이 증가하였다. 충격에너지 중 균열개시에너지와 동적파괴인성치의 관계를 설명하기 위하여 변형율 에너지와 노치에서의 응력 분포를 이용하여 간단한 모델을 제시하였으며, 이로부터 균열개시에너지는 동적 파괴 인성치의 자승에 비례하고 탄성계수에 반비례하는 것을 보였다.

• 소성∙가공
• /
• 제19권5호
• /
• pp.311-319
• /
• 2010

Rare earth metal Ce has a relatively low melting point and high specific gravity. Because of its significantly high affinity to oxygen, nitrogen and sulfur, it is highly usable as a steel refining agent. However, because Ce compound has relatively high specific gravity, it is difficult to be separated from molten steel through floatation, and it degrades the purity of molten steel, or may clog the nozzle in continuous casting. Such problem may be solved by using an appropriate deoxidation agent together with Ce and settling molten steel sufficiently after refining. Thus a fundamental study in the formation behavior of non-metallic inclusion in Ce added Hyper Duplex STS melts was investigated. The addition amount of Ce, melt temperature were considered as experimental variables. A main non-metallic inclusion in mother alloy is 51(wt%MnO) - 27.6(wt%SiO$_2$)- 10.9(wt%$Cr_2O_3$). Non-metallic inclusion was dramatically decreased and the particle size was fined as the amount of Ce increased. Moreover (%MnO) and (%SiO$_2$) of non-metallic inclusion were decreased. But (%$Al_2O_3$)were relatively increased. The number of non-metallic inclusion were decreased and the large particle size were increased by increasing the temperature of molten steel.