• Journal of the Korean Ceramic Society
• /
• v.32 no.9
• /
• pp.977-988
• /
• 1995

Several oxide (ZrO2, Al2TiO5, reactive Al2O3) and nonoxide (SiC, Si3N4, "ALON" (5AlN.9Al2O3)) additives were used as a microfiller for alumina based LCC (Low-Cement-Castable). High temperature prooperties (HMOR, softening under load) and the phase changes of developed LCC on various sintering temperatures were examined. In addition, thermal shock test and corrosion test were accomplished. Based on these data the effects of each microfiller on the properties of LCC were established comparing to those of the commercial LCC with amorphous silica as a microfiller. The castables, containing reactive alumina, ZrO2 and "ALON" (5AlN.9Al2O3) as a first portion, exhibited considerably higher HMOR-values over 100$0^{\circ}C$, better creep behavior, and thermal shock resistance than those of castables with amorphous silica. The LCC with 5% Al2TiO5 showed no corrosion against molten aluminum.nst molten aluminum.

• Journal of the Korean Ceramic Society
• /
• v.36 no.8
• /
• pp.876-885
• /
• 1999

In order to develop high performance basic dam block for tundish vessel in steel-making binders and additives on hydration and thermal characteristics of magnesiz castable refractories were studied. Crack initiation and propagation in cement bonded magnesia castables due to slaking of magnesia clinker at drying process were suppressed by using spinel clinker instead of magnesia powder. In case of Na2O$.$2CaO$.$P2O5(NC2P) bonded castable crack initiation due to slaking of magnesia clinker did not occur but bending strength at high temperature was low. Mechanical properties of NC2P bonded castable refractories at high temperature were improved by using magnesia clinker that contains low SiO2 contents.

• Journal of the Korean Ceramic Society
• /
• v.40 no.8
• /
• pp.791-797
• /
• 2003

The special binding mechanism developed provides higher density, lower porosity and higher strengths compared with conventional castables. $\rho$-alumina was employed as a binder materials and nano-sized clay colloidal was added to enhance the drying strength preparing for the alumina vibrated castable. Lower water requirement for casting results in a denser product. The mechanical properties with dimensional stability and corrosion resistance behaviors have been improved by controlling the matrix compositions of the castable. The modulus of rupture and compressive strength after heat treatment at 150$0^{\circ}C$ are 92.34 kgf/$\textrm{cm}^2$ and 370 kgf/$\textrm{cm}^2$ respectively. The activation energy of mullite formation is 11.47 kcal/mol.

• Journal of the Korean Ceramic Society
• /
• v.17 no.2
• /
• pp.69-74
• /
• 1980

This study deals with the wire content, wire diameter, aspect ratio , it's arrangement of steel, wire fiber and the sorts of castable which affected the character of steel wire fiber reinformced refractory castable. Two kinds of alumina based refractory castables, one is for 1650℃ and the other is for 1800℃, and stainless steel which is SUS 304 type 0.25, 0.34 , 0.37 and 0.50m/min diameter were used respectively. Aspect ratio was adjusted to 50, 75, 100 and steel fiber content was also adjusted to 1-4wt% each. The results of the experiment were as follows : 1. At firing temperature around 1,000℃, MOR is increased with increasing wire content and aspect ratio with decreasing firing temperature, which depends on the Romualdi's Fiber Spacing Theory. But for calculation of the fiber spacing, Swamy equation is more a aplicable to the extensive fiber mixing conditions. However, the condition differs from the above at firing temperature around 1,350℃ ,because of the degradation of wire and the progress of sintering of castable. 2. Linear change is getting larger corresponding to the increase of wire content, and the spaling resistivity is increasing corresponding to the increase of wire content and to aspect ratio, and with decreasing wire diameter. 3. Firing shrinkage under load is getting greater as higher wire content, and the shrinkage of the test pieces which fiber is vertically oriented is getting greater than the test pieces which fiber is randomly oriented.