• Journal of Mechanical Science and Technology
• /
• 제14권10호
• /
• pp.1021-1027
• /
• 2000

In this study, fatigue tests were performed to examine the effects of micro drill hole on fatigue limit of as cast and austempered ductile cast iron (ADI) using the rotary bending fatigue tester. As results, micro drill holes ($diameter{\leq}0.4mm$) did not influence the fatigue limit of ADI, compared to annealed ductile cast iron; the critical defect size of crack initiation, in ADI was larger than as cast. If the ${\sqrt{area}}$ of micro drill hole and graphite nodule in ADI are comparable, crack initiates at the graphite nodule. When the ruggedness developes through austempering treatment process, microstructure on crack initiation at micro drill hole is tougher than that of as cast ductile cast iron.

• 한국표면공학회지
• /
• 제20권4호
• /
• pp.144-153
• /
• 1987

In the case of dipping the Ni-Resist cast iron into molten aluminum with iron content, the thickness of intermetallic compound was remarkably increased with increasing iron content. The thickness was shown by following equation in the range of 1-3% iron content; $x=22.5t^{1/2}+4.47{\cdot}t{\cdot}(Fe%)$. where, x is thickness(${\mu}m$), t the time (minute), Fe% the iron w/o. When the Ni-Resist cast iron was dipped into the molten aluminum containing zinc content, the intermetallic compound thickness was also increased with increasing zinc contents. And thickness was represented by the following equation in the range of 2-10% zinc content; $x=3.46t^{1/2}+0.27{\cdot}t{\cdot}(Zn%)$. However, in the case of dipping the Ni-resist cast iron into molten aluminum with silicon content, the thickness of intermetallic compound was decreased with increasing silicon content, as shown in the following equation; $x=7.17t^{1/2}-0.15{\cdot}t{\cdot}(Si%)$. The intermetallic compound formed onto Ni-Resist cast iron was identified to be $FeAl_3\;and\;Fe_3Al$. As the result of hardness measurement, the peak hardness appeared in the intermetallic compound at near interface of the cast iron and the compound.

• 헤리티지:역사와 과학
• /
• 제53권2호
• /
• pp.4-23
• /
• 2020

이 연구는 우리나라 철 주조기술의 다양성과 기술 체계를 규명하기 위한 목적으로 진행되었으며, 이를 위해 고문헌 조사 및 유물 분석, 제작 도구와 제작 기술에 대한 현지 조사 그리고 주조와 거푸집에 사용된 재료의 과학 분석 등을 실시하였다. 불미기술은 송풍구인 풀무를 이용하여 주철을 녹인 뒤 그 쇳물을 토제 거푸집에 부어 주물을 완성하는 철 주조기술로 현재 유일하게 제주도에서만 전승되고 있는데, 모래 거푸집을 사용하는 육지와 비교해 토제 거푸집을 사용하고 있다는 것이 큰 차이점이라 할 수 있다. 무쇠솥 주조기술에는 석비레, 모래, 점토 등을 섞어 만든 모래 거푸집을 이용한 주물사주조법(鑄物砂鑄造法)과 점토에 볏짚과 갈대 등을 섞어 만든 토제 거푸집을 이용한 도토주조법(陶土鑄造法)이 사용되고 있다. 주물사주조법에 의한 무쇠솥 주조는 거푸집 만들기, 속심 제작, 쇳물 작업, 거푸집에 쇳물 붓기, 완성품 다듬기 등 5단계의 작업공정을 거치며, 도토주조법에 의한 무쇠솥 주조는 거푸집 만들기, 거푸집 굽기, 질먹 입히기, 쇳물 작업, 쇳물 붓기, 완성품 다듬기 등 크게 6단계의 작업 공정으로 이루어진다. 두 주조법은 거푸집의 재료, 거푸집을 불에 굽고 질먹을 입히는 제작 공정에서 차이를 보인다. 이번에 연구한 불미기술은 토제 거푸집 무쇠솥 주조로 진흙 채취 및 반죽, 거푸집 제작, 초벌 굽기, 화적모살 및 질먹 바르기, 건조 및 비얄질, 거푸집 합장, 둑(용광로)제작, 재벌 굽기, 제련, 쇳물 붓기, 주물 다듬기 등 단계별 주조 공정에 사용된 재료 및 도구 분석과 제작 기술에 담겨진 과학 기술 원리를 규명하여 우리 고유 철 주조기술의 기술 체계를 밝혀 보았다. 그리고 무쇠솥 도토주조를 위해 이용한 재료와 완성품을 과학 분석한 결과, 거푸집은 주성분이 SiO₂, Al₂O₃, Fe₂O₃으로 이루어진 진흙과 모래이고, 이형재는 SiO₂, Al₂O₃, Fe₂O₃, K₂O가 함유된 흑연이며, 완성된 무쇠솥의 미세 조직은 시멘타이트(Fe₃C)와 펄라이트(페라이트와 시멘타이트의 층상 구조)로 이루어진 백주철 조직임을 확인하였다.

• Smart Structures and Systems
• /
• 제7권4호
• /
• pp.241-262
• /
• 2011

Cast iron pipe has been used as a water distribution technology in North America since the early nineteenth century. The first cast iron pipes were made of grey cast iron which was succeeded by ductile iron as a pipe material in the 1940s. These different iron alloys have significantly different microstructures which give rise to distinct mechanical properties. Insight into the non-destructive structural condition assessment of aging pipes can be advantageous in developing mitigation strategies for pipe failures. This paper examines the relationship between the small-strain and large-strain properties of exhumed cast iron water pipes. Nondestructive and destructive testing programs were performed on eight pipes varying in age from 40 to 130 years. The experimental program included microstructure evaluation and ultrasonic, tensile, and flexural testing. New applications of frequency domain analysis techniques including Fourier and wavelet transforms of ultrasonic pulse velocity measurements are presented. A low correlation between wave propagation and large-strain measurements was observed. However, the wave velocities were consistently different between ductile and grey cast iron pipes (14% to 18% difference); the ductile iron pipes showed the smaller variation in wave velocities. Thus, the variation of elastic properties for ductile iron was not enough to define a linear correlation because all the measurements were practically concentrated in single cluster of points. The cross-sectional areas of the specimens tested varied as a result of minor manufacturing defects and levels of corrosion. These variations affect the large strain testing results; but, surface defects have limited effect on wave velocities and may also contribute to the low correlations observed. Lamb waves are typically not considered in the evaluation of ultrasonic pulse velocity. However, Lamb waves were found to contribute significantly to the frequency content of the ultrasonic signals possibly resulting in the poor correlations observed. Therefore, correlations between wave velocities and large strain properties obtained using specimens manufactured in the laboratory must be used with caution in the condition assessment of aged water pipes especially for grey cast iron pipes.

• 보존과학회지
• /
• 제28권4호
• /
• pp.367-376
• /
• 2012

철기 생산 기술은 당시 사회 발전을 가늠하는 척도로서 과거의 제철 방법을 이해하기 위한 철기 유물의 미세조직과 개재물에 대한 다양한 연구가 진행되고 있다. 본 연구에서는 고려시대로 추정되는 고양 벽제 제철 유구에서 일괄로 수습된 철제 유물의 시편을 채취하여 광학현미경과 미세경도시험기, SEM-EDS를 이용하여 미세 조직의 성분분석을 통해 제철과 제련 기술을 추론하여 보았다. 연구결과 철괴는 주철괴와 탄소강 철괴로 분류되었다. 주철괴의 경우 백주철 조직과 인(P)의 함량이 높은 회주철 조직으로 분류되었으며 회주철 내 높은 P의 함량은 석회질 등의 융제가 첨가되며 혼입된 것으로 판단된다. 따라서 주철 조직의 철괴 및 고탄소강 철괴는 제련공정을 거치지 않은 선철들로 추정된다. 또한 철기 제작에는 크게 두가지 방법이 사용된 것으로 판단된다. 첫번째는 주물에 주철을 부어 제작하는 주철괴 제작 방법이며, 두번째는 선철의 제련 공정을 통하여 생산되는 탄소강을 제작하는 방법이다. 특히 탄소강의 고른 강 조직과 적은 양의 MnS 개재물은 현대 제철 조직과 매우 유사한 특징을 지니나 고양 벽제 제철유구에서 수습된 탄소강 내 Mn의 함유에 대하여 판단하기에는 좀 더 많은 연구가 이루어져야 할 것이며, 주철의 제강공정을 통한 고탄소강의 생산 가능성도 염두에 두어야 할 것으로 사료된다.

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.154-165
• /
• 1997

Abrasive wear characteristics of high Cr white cast iron-based hardfacing were investigated using the rubber wheel abrasion wear test method according with the ASTM G65-85. Mild steel was also tested for comparison with high Cr cast iron hardfacing. Wear experiments, where the applied force, wheel revolution rate and abrasive powder feed rate were selected as test valuables, were planned and analyzed by response surface method to evaluate wear statistically and quantitatively. Weight loss of high Cr cast iron hardfacing was mostly affected by the applied force and wheel revolution rate, and little by the powder feed rate. Weight loss of mild steel was greatly affected by the wheel revolution rate and powder feed rate, and slowly and steadily increased with the applied force. Abrasive wear mechanism of high Cr cast iron and mild steel was discussed in the light of the wear test results.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 추계학술대회 논문집
• /
• pp.312-317
• /
• 2002

A experimental try was conducted for the purpose of establishment of the cast iron modification by the metal spray method. The friction and wear resistance properties of the metal sprayed cast iron surface were evaluated. The application experiment for the cast iron modification by the metal spray method was conducted in order to develope the restoring method of the scrapped cast iron cylinder liner of the marine engine.

• 한국재료학회지
• /
• 제7권4호
• /
• pp.310-316
• /
• 1997

The effects of carbide and matrix structures on the abrasion wear resistance of multi-component white cast irons with 3.0 mass%C have been studied in this paper. Four different heats were poured in order to obtain the specimens with different combinations of the carbide structures: a basic iron(3.0 mass%C-5.0 mass%Cr-5.0 mass%V-5.0 mass% Mo-12.5mass%W)for M$_{6}$C and M$_{7}$C$_{3}$ carbides, and a Cr free iron(3.0 mass%C-5.0 mass%V-2.5mass%Mo-12.5 mass%W) for MC and M6C carbides. A conventional high Cr free free iron(3.0 mass%C-5.0 mass%V-2.5 mass%Mo-12.5 mass%W) for MC and M6C carbides. A conventional high Cr white cast iron was also poured to compare its wear resistance with those of the multi-component white cast irons. In the as-cast condition, the range of abrasive wear rate(Rw=mg/min) was from 4.15 to 5.98 . The lowest Rw, which means the highest wear resistance, was obtained in the basic iron with nodular MC, lamellar M$_{2}$C and cellular M$_{7}$C$_{3}$ carbides. On the other hand, the Rw of the high Cr white cast iron ranked between the basic iron and the Mo and W free iron. In each alloy, the Rw of air hardened or tempered specimen was lower than that of the as-cast one because of the change of matrix structures by the heat treatments. The Rw of the hear treated speci-mens increased in the order Mo and W free iron, basic iron, Cr free iron, high Cr iron, and V free iron.n.n.n.

• 한국주조공학회지
• /
• 제27권1호
• /
• pp.24-30
• /
• 2007

The effects of C, Si and RE additions on the tendency of chill formation of ductile cast iron obtained from metal mold casting were investigated. In case of metal mold cast, the ductile cast iron with 2.5%Si had pearlitic matrix, and specimens with 2.9%Si had bull's eye type regardless of C contents. As-cast specimen with a large amount of fine graphites could be obtained by adding 0.2% RE. Normalizing process was necessary to remove carbide and form a large amount of spheroidal graphites for the as-cast specimens. Good mechanical properties could be obtained by heat-treatment of as-cast specimens with pearlitic matrix. Normalizing the specimens with RE caused the reduction in mechanical properties.

• 비파괴검사학회지
• /
• 제32권2호
• /
• pp.155-161
• /
• 2012

초음파 속도를 이용하여 다양한 종류의 주철에 대해 미세구조와 품질 특성을 평가하였다. 상용으로 사용되는 3종의 회주철 및 3종의 구상흑연주철을 준비하였으며, 열처리 미세구조의 영향을 평가하기 위해 구상흑연주철을 어닐링 열처리를 다르게 하여 시편을 준비하였다. 초음파 전파 속도 측정, 미세구조(펄라이트 분율, 흑연의 길이 및 구상화율) 정량화, 경도 측정을 행하여 이들 파라미터 사이의 경험적 상관관계를 확인하였다. 구상흑연주철의 초음파 전파 속도가 회주철에서의 속도보다 크게 나타났다. 구상흑연주철에서 펄라이트 미세조직의 분율이 감소할수록 경도 및 초음파 속도는 감소하였다. 초음파 속도를 주철 소재의 품질관리를 위한 비파괴평가 파라미터로서 사용할 수 있는 가능성을 보여주었다.