• Nuclear Engineering and Technology
• /
• 제55권6호
• /
• pp.2335-2347
• /
• 2023

As medical facilities are usually built at urban areas, special concrete aggregates and evaluation methods are needed to optimize the design of concrete walls by balancing density, thickness, material composition, cost, and other factors. Carbon treatment rooms require a high radiation shielding requirement, as the neutron yield from carbon therapy is much higher than the neutron yield of protons. In this case study, the maximum carbon energy is 430 MeV/u and the maximum current is 0.27 nA from a hybrid particle therapy system. Hospital or facility construction should consider this requirement to design a special heavy concrete. In this work, magnetite is adopted as the major aggregate. Density is determined mainly by the major aggregate content of magnetite, and a heavy concrete test block was constructed for structural tests. The compressive strength is 35.7 MPa. The density ranges from 3.65 g/cm³ to 4.14 g/cm³, and the iron mass content ranges from 53.78% to 60.38% from the 12 cored sample measurements. It was found that there is a linear relationship between density and iron content, and mixing impurities should be the major reason leading to the nonuniform element and density distribution. The effect of this nonuniformity on radiation shielding properties for a carbon treatment room is investigated by three groups of Monte Carlo simulations. Higher density dominates to reduce shielding thickness. However, a higher content of high-Z elements will weaken the shielding strength, especially at a lower dose rate threshold and vice versa. The weakened side effect of a high iron content on the shielding property is obvious at 2.5 µSv=h. Therefore, we should not blindly pursue high Z content in engineering. If the thickness is constrained to 2 m, then the density can be reduced to 3.3 g/cm³, which will save cost by reducing the magnetite composition with 50.44% iron content. If a higher density of 3.9 g/cm³ with 57.65% iron content is selected for construction, then the thickness of the wall can be reduced to 174.2 cm, which will save space for equipment installation.

• Korean Journal of Soil Science and Fertilizer
• /
• 제12권4호
• /
• pp.179-187
• /
• 1980

1) Soils (volcanic ash and muck) were fractionated into particle-size separates (200 - 20, 20 - 2, 2 - 0.5 and finer than $0.5{\mu}$ in diamter), and of which the silt fraction was further fractionated into specific gravity separates (more than 2.0, 2.0 - 1.7, 1.7 - 1.4 and less than 1.4 in $g/cc^3$). And total organic and inorganic phosphorus in the separates were determined. 2) The amounts of total, organic and inorganic phosphorus distributed in the particle-size separates were as follows fine clay > coarse clay > silt > fine sand fraction. The increase rate in the amounts of phosphorus was great in the separates finer than $20{\mu}$, and greatest in the fine clay fraction. 3) The amounts of total, oganic and inorganic phosphorus distributed in the specific gravity separates were as follows: 2.0 - 1.7 > 1.7 - 1.4 > heavier than 2.0 fraction. The increase rate in the amounts of phosphorus was in the following order 2.0 - 1.7 > 1.7 - 1.4 > heavier than 2.0 fraction. 4) Distribution of carbon, amorphous aluminum and free iron oxides in the particle-size separates and the specific gravity separates were examined, and the distribution and the formes of organo-minera1 complexes in the separates were discussed to shed light on the factors affecting the distribution of phosphorous into the separates. And it was estimated that there was close relation among the distribution of organic and inorganic phosphorus, and the distribution and the formes of organo-minera1 complexes.

• Korean Chemical Engineering Research
• /
• 제47권5호
• /
• pp.580-586
• /
• 2009

In this study, co-combustion characteristics of Chinese bituminous coal and North Korean anthracite were investigated using a 2 MWe scale circulating fluidized bed power plant. At first, the combustion efficiency of bituminous coal of China and Australia as a function of excess air ratio and temperature were observed. The results showed that the combustion efficiency was influenced by particle size and volatile content of coal, the combustion efficiency of Chinese bituminous coal was over 99.5%. The unburned carbon particles from fly ash and bottom ash were a content 5~7% and 0.3%, respectively. The combustion efficiency with the mixture ratio 20% of bituminous coal and anthracite decreased over 5% because of the increase of entrained particles by a small average particle size of anthracite in the combustor. However, the outlet concentration of $SO_2$ and $NO_x$ was not changed remarkably. The concentrations of the typical air pollutants such as $NO_x$ and $SO_2$ were 200~250 ppm($O_2$ 6%), 100~320 ppm($O_2$ 6%) respectively. The outlet concentration of $NO_x$ was decreased to 30~65% with $NH_3$ supplying rate of 2~13 l/min in SCR process. The $SO_x$ removal efficiency was up to 70% by in-furnace desulfurization using limestone with Ca/S molar of approximately 6.5. With wet scrubbing using $Mg(OH)_2$ as absorbent, the $SO_x$ removal efficiency reached 100% under near pH 5.0 of scrubbing liquid.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제34권2호
• /
• pp.121-127
• /
• 2010

The in-furnace desulfurization technique is applied to the $O_2/CO_2$ combustion system for the carbon capture and storage (CCS) process because this combustion system does not need an additional chamber for the desulfurization. $CaCO_3$ sorbent particles, which have a wide range in size from a few nanometers to several tens of micrometers, are used for this process. In this study, an experimental system which can simulate the $O_2/CO_2$ combustion system was developed. $CaCO_3$ sorbent particles were exposed to the high temperature reactor at $1200^{\circ}C$ with various residence times (0.33-1.46 s) in air and $CO_2$ atmospheric conditions, respectively. The sorbent particles were then sampled at the inlet and outlet of the reactor and analyzed qualitatively/quantitatively using SMPS, XRD, TGA, and SEM. The results showed that the residence time and atmospheric condition in a high temperature reactor can affect the characteristics of the $CaCO_3$ sorbent particles used in the in-furnace desulfurization technique, such as the calcination rate and reaction mechanism.

• Journal of the Korean Society of Marine Environment & Safety
• /
• 제22권2호
• /
• pp.220-227
• /
• 2016

In this paper, polychlorinated biphenyls (PCBs) were measured in surface sediments collected three times (June, October, December, 2013), inside Jeju Harbor as major harbors of Jeju Island. The concentration of PCBs inside Jeju Harbor was in the range of 1.62~4.45 (mean) ng/g on a dry weight basis and the levels were very low. In the analysis of PCBS homologue patterns, high-chlorinated PCB congeners were dominant in surface sediments inside Jeju Harbor, indicating that their sources were originated from shipping activity. In the relationships between PCBs concentrations and particle size (mud, sand and gravel) in surface sediments, PCBs concentrations were higher in the sediments with higher mud content, indicating that higher PCBs were distributed with increasing sediments of fine gradules. The PCBs concentrations in surface sediments in this study were very low, compared with ER-L (effect range-low) and TEL (threshold effects level) among sediment quality guideleines (SQGs) applied in foreign countries, such as USA, Canada, and Australia, etc), indicating that their biological effects on the bottom organisms in marine environment were expected to be very low.

• Korean Chemical Engineering Research
• /
• 제54권6호
• /
• pp.838-846
• /
• 2016

Most of combustion processess used in industries require recovering or removing flue gas components. Recently a new MBA (moving bed adsorption) process for recovering $CO_2$ using zeolite 13X was developed. In this study, adsorption experiments for carbon dioxide, nitrogen, sulfur dioxide, and water vapor on zeolite 13X were carried out. Adsorption equilibrium and adsorption rate into solid particle were investigated. Langmuir, Toth, and Freundlich isotherm parameters were calculated from the experiment data at various temperatures. Experimental results were consistent with the theoretically predicted values. Also $CO_2$ adsorption amount was measured under the conditions with impurities such as $SO_2$ and $H_2O$. Binary adsorption data were well fitted to the extended Langmuir isotherm using parameters obtained from pure component experiment. However, $H_2O$ impurity less than, roughly, ${\sim}10^{-5}H_2O\;mol/g$ zeolite 13X enhanced slightly $CO_2$ adsorption. Spherical particle diffusion model well described experimentally measured adsorption rate. Diffusion coefficients and activation energies of $CO_2$, $SO_2$, $N_2$, $H_2O$ were obtained. Diffusion coefficients of $CO_2$ and $SO_2$ decreased with small amount of preadsorbed impurity. Parameter values from this study will be helpful to design of real commercial adsorption process.

• Resources Recycling
• /
• 제8권3호
• /
• pp.9-17
• /
• 1999

The study investrgated the properti es of lh$\xi$ dust~ from felToalloy manufacture, The chemical composition, composItron material, particle size and shapes of the bulk dust, sized dust and magnetically separated dust were llivestigated. As the result, we s suppose that the dust from HLgh Carbon Fenomauganesc Manufacturing Process is not sufficient as soource material of Mn because of the low Mn conteut (13.5%) aud complicated composition material The dust from Bag Filter of AOD Process is m mainly made up of $0.2~2\mu\textrm{m}$ $Mn_3O_4$ (Hausmatmite) particle in spherical shape and the Mn content is 63.1%. The dust from Cooler of AOD Process is mainly made up of coarse $Ca(OH)_2$ Mn, $Fe_yO_2$ $SiO_2$ and fine $Mn_3O_1$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.434-435
• /
• 2012

Plasma enhanced chemical vapor deposition (PECVD) silicon dioxide thin films have many applications in semiconductor manufacturing such as inter-level dielectric and gate dielectric metal oxide semiconductor field effect transistors (MOSFETs). Fundamental chemical reaction for the formation of SiO2 includes SiH4 and O2, but mixture of SiH4 and N2O is preferable because of lower hydrogen concentration in the deposited film [1]. It is also known that binding energy of N-N is higher than that of N-O, so the particle generation by molecular reaction can be reduced by reducing reactive nitrogen during the deposition process. However, nitrous oxide (N2O) gives rise to nitric oxide (NO) on reaction with oxygen atoms, which in turn reacts with ozone. NO became a greenhouse gas which is naturally occurred regulating of stratospheric ozone. In fact, it takes global warming effect about 300 times higher than carbon dioxide (CO2). Industries regard that N2O is inevitable for their device fabrication; however, it is worthwhile to develop a marginable nitrous oxide free process for university lab classes considering educational and environmental purpose. In this paper, we developed environmental friendly and material cost efficient SiO2 deposition process by substituting N2O with O2 targeting university hands-on laboratory course. Experiment was performed by two level statistical design of experiment (DOE) with three process parameters including RF power, susceptor temperature, and oxygen gas flow. Responses of interests to optimize the process were deposition rate, film uniformity, surface roughness, and electrical dielectric property. We observed some power like particle formation on wafer in some experiment, and we postulate that the thermal and electrical energy to dissociate gas molecule was relatively lower than other runs. However, we were able to find a marginable process region with less than 3% uniformity requirement in our process optimization goal. Surface roughness measured by atomic force microscopy (AFM) presented some evidence of the agglomeration of silane related particles, and the result was still satisfactory for the purpose of this research. This newly developed SiO2 deposition process is currently under verification with repeated experimental run on 4 inches wafer, and it will be adopted to Semiconductor Material and Process course offered in the Department of Electronic Engineering at Myongji University from spring semester in 2012.

• Advanced Composite Materials
• /
• 제17권1호
• /
• pp.25-40
• /
• 2008

The research and development in soundproof materials for preventing noise have attracted great attention due to their social impact. Noise insulation materials are especially important in the field of soundproofing. Since the insulation ability of most materials follows a mass rule, the heavy weight materials like concrete, lead and steel board are mainly used in the current noise insulation materials. To overcome some weak points in these materials, fiber reinforced composite materials with lightweight and other high performance characteristics are now being used. In this paper, innovative insulation sheet materials with carbon and/or glass fabrics and nano-silica hybrid PU resin are developed. The parameters related to sound performance, such as materials and fabric texture in base fabric, hybrid method of resin, size of silica particle and so on, are investigated. At the same time, the wave analysis code (PZFlex) is used to simulate some of experimental results. As a result, it is found that both bundle density and fabric texture in the base fabrics play an important role on the soundproof performance. Compared with the effect of base fabrics, the transmission loss in sheet materials increased more than 10 dB even though the thickness of the sample was only about 0.7 mm. The results show different values of transmission loss factor when the diameters of silica particles in coating materials changed. It is understood that the effect of the soundproof performance is different due to the change of hybrid method and the size of silica particles. Fillers occupying appropriate positions and with optimum size may achieve a better effect in soundproof performance. The effect of the particle content on the soundproof performance is confirmed, but there is a limit for the addition of the fillers. The optimization of silica content for the improvement of the sound insulation effect is important. It is observed that nano-particles will have better effect on the high soundproof performance. The sound insulation effect has been understood through a comparison between the experimental and analytical results. It is confirmed that the time-domain finite wave analysis (PZFlex) is effective for the prediction and design of soundproof performance materials. Both experimental and analytical results indicate that the developed materials have advantages in lightweight, flexibility, other mechanical properties and excellent soundproof performance.

• Journal of Korean Society of Environmental Engineers
• /
• 제34권9호
• /
• pp.597-603
• /
• 2012

To investigate the effects of weir construction on sediment characteristics of river bed, we conducted sediments sampling on the 9 locations near the weir, Kangchun, Yuju and Ipo in Namhan-River. Physical and chemical characteristics of sediments were analyzed by measuring particle size distribution, water content, Ignition loss, COD (Chemical Oxyzen Demand), TOC (Total Organic Carbon), TP (Total Phosphorus), SRP (Soluble Reactive Phosphorus) and TN (Total Nitrogen). Particle classification of all three weir sediments showed sandy loam that was caused by the river bed dredging. Due to the presence of weir, Ignition loss, COD, TOC, TP, SRP and TN showed similar trend such as the concentrations of upward weir had higher than those of downward weir. For the case of SRP concentration and C/N ratio, however, there is not much difference in the sediment characteristics compared to the those of sediments before weir construction. Therefore, It can be predicted that there are little effects of weir construction on sediment characteristics. However, weir construction could influence water quality of the river by controlling the transport and the accumulation of suspended materials from rainfall. Therefore, more intensive monitoring is required to examine the magnitude and patterns of sediment accumulation which could influence overlying water quality.