• Structural Engineering and Mechanics
• /
• 제55권3호
• /
• pp.511-523
• /
• 2015

Damaged steel-concrete composite girders can be repaired and retrofitted by epoxy-bonded carbon fiber-reinforced polymer (CFRP) sheets to the critical areas of tension flanges. This paper presents the results of a study on the behavior of damaged steel-concrete composite girders repaired with CFRP sheets under static loading. A total of seven composite girders made of I20A steel sections and 80mm-thick by 900mm-wide concrete slabs were prepared and tested. CFRP sheets and prestressed CFRP sheets were used to repair the specimens. The specimens lost the cross-sectional area of their tension flanges with 30%, 50% and 100%. The results showed that CFRP sheets had no significant effect on the yield loads of strengthened composite girders, but had significant effect on the ultimate loads. The yield loads, elastic stiffness, and ultimate bearing capacities of strengthened composite girders had been changed as a result of prestressed CFRP sheets, the utilization ratio of CFRP sheets could be effectively improved by applying prestress to CFRP sheets. Both the yield loads and ultimate bearing capacities had been changed as a result of steel beam's flange damage level and CFRP sheets could cover the girders' shortage of bearing capacity with 30% and 50% flange damage, respectively.

• Steel and Composite Structures
• /
• 제31권2호
• /
• pp.159-172
• /
• 2019

Strengthening of civil infrastructure with advanced composites have recently become one of the most popular methods. The use of Fiber Reinforced Polymer (FRP) strips plates and fabric for strengthening of reinforced concrete structures has well established design guidelines and standards. Research on the application of FRP composites to steel structures compared to concrete structures is limited, especially for shear strengthening applications. Whereas, there is a need for cost-effective system that could be used to strengthen steel high-way bridge girders to cope with losses due to corrosion in addition to continuous demands for increasing traffic loads. In this study, a parametric finite element study is performed to investigate the effect of applying thick CFRP strips diagonally on webs of plate girders on the shear strength of end-web panels. The study focuses on illustrating the effect of several geometric parameters on nominal shear strength. Hence, a formula is developed to determine the enhancement of shear strength gained upon the application of CFRP strips.

• Composites Research
• /
• 제37권3호
• /
• pp.186-189
• /
• 2024

본 연구는 나노필러가 혼합된 열가소성 탄소섬유강화 복합재료(Carbon fiber reinforced thermoplastic polymer, CFRTP)의 물성을 비교 평가하였다. Polyamide 6 (PA6) 수지에 Multi-wall carbon nano tube (MWCNT), Silicon oxide, Core shell rubber, Aramid nano fiber 등의 다양한 나노필러를 혼합한 후, 이를 기지재(Matrix)로 탄소섬유강화복합 재료(CFRP)를 제조하여 그 물성을 측정하였다. 나노필러의 종류와 혼합비율에 따라, 인장강도, 층간계면결합력 (Inter-laminar shear strength), Izod 충격 강도 등이 측정되었다. 인장 강도와 충격 강도의 경우 Core shell rubber를 혼합한 경우 가장 높은 물성을 가졌으나, 계면결합력은 silicon oxide를 1 wt.% 이하 혼합하였을 때 최적값을 가졌다.

• Composites Research
• /
• 제24권5호
• /
• pp.34-38
• /
• 2011

탄소나노튜브가 발견된 이후로, 고분자 수지의 기계적, 전기적 물성을 증대시키는 보강재로서 많은 연구가 수행되어 왔다. 더 나아가, 탄소나뉴튜브를 탄소섬유복합재 (CFRP)의 기지가 되는 수지를 보강시키는 데 이용하는 연구도 최근 활발해지고 있는 추세이다. 단일벽탄소나노튜브가 각각 0.2 %, 0.5 %의 중량비로 에폭시 수지에 먼저 분산, 혼합되었다. 이 혼합액을 CFRP를 제작하는데 주로 쓰이는 방법 중 하나인 진공 수지 충전 공정법 (vacuum assisted resin transfer molding, VARTM)으로 탄소섬유 프리폼에 주입하는 방법과 습식 현장 적층법 (wet lay-up)의 두가지 다른 방법으로 복합재를 제작 하였다. 각각의 제작된 시편에 대하여, 층간전단강도 (interlaminar shear strength, ILSS)를 측정하여, 층간전단강도와 공정의 상관관계, 탄소나노튜브의 보강효과에 대하여 조사했다. 탄소나노튜브/에폭시 복합재의 경우 기계적 물성의 향상을 가져왔으나 이를 기지재로 사용한 탄소섬유복합재의 층간전단강도는 특히 VARTM 공정의 경우, 탄소나노튜브의 첨가에 따른 수지의 점도 증가로 인한 공정상의 문제로 기대만큼의 물성향상을 가져오지는 못한 것을 확인하였다.

• Smart Structures and Systems
• /
• 제4권4호
• /
• pp.391-406
• /
• 2008

This study attempts to develop a real-time debonding monitoring system for carbon fiber-reinforced polymer (CFRP) strengthened structures by continuously inspecting the bonding condition between the CFRP layer and the host structure. The uniqueness of this study is in developing a new concept and theoretical framework of nondestructive testing (NDT), in which debonding is detected without relying on previously-obtained baseline data. The proposed reference-free damage diagnosis is achieved based on the concept of time reversal acoustics (TRA). In TRA, an input signal at an excitation point can be reconstructed if the response signal measured at another point is reemitted to the original excitation point after being reversed in the time domain. Examining the deviation of the reconstructed signal from the known initial input signal allows instantaneous identification of damage without requiring a baseline signal representing the undamaged state for comparison. The concept of TRA has been extended to guided wave propagations within the CFRP-strengthened reinforced concrete (RC) beams to improve the detectibility of local debonding. Monotonic and fatigue load tests of large-scale CFRP-strengthened RC beams are conducted to demonstrate the potential of the proposed reference-free debonding monitoring system. Comparisons with an electro-mechanical impedance method and an inferred imaging technique are provided as well.

• Structural Engineering and Mechanics
• /
• 제87권4호
• /
• pp.375-389
• /
• 2023

In many fiber concrete beams with Carbon Fiber Reinforced Polymer (CFRP), debonding occurs between the carbon sheets and the concrete due to the low strength of the bonding resin. A total of 42 fiber concrete beams with a cross-section of 10×10 cm with a span length of 50 cm are fabricated and retrofitted with CFRP and subjected to a 4-point bending test. Graphene Oxide (GO) at 1, 2, and 3 wt% of the resin is used to improve the mechanical properties of the bonding resins, and the effect of length, width, and the number of layers of CFRP and resin material are investigated. The crack pattern, failure mode, and stress-strain curve are analyzed and compared in each case. The results showed that adding GO to polyamine resin could improve the bonding between the resin and the fiber concrete beam. Furthermore, the optimum amount of nanomaterials is equal to 2% by the weight of the resin. Using 2% nanomaterials showed that by increasing the length, width, and number of layers, the bearing and stiffness of fiber concrete beams increased significantly.

• Steel and Composite Structures
• /
• 제21권2호
• /
• pp.411-427
• /
• 2016

While the cyclic behaviour of fiber-reinforced polymer (FRP)-confined columns is studied rather extensively, the cyclic response especially the energy dissipation of FRP-confined damaged and undamaged square RC columns is not yet fully understood. In this paper, an experimental and numerical investigation was conducted to study the cyclic behavior of two different types of Carbon FRP (CFRP)-confined square RC columns: strengthened and repaired. The main variables investigated are initial damage, confinement of CFRP, longitudinal steel reinforcement ratio. The experimental results show that lower initial damage, added confinement with CFRP and longitudinal reinforcement enhance the ductility, energy dissipation capacity and strength of the columns, decrease the stiffness and strength degradation rates of all CFRP-confined square RC columns. Two hysteretic constitutive models were developed for confined damaged and undamaged concrete and cast into the non-linear beam-column fiber-based models in the software Open System for Earthquake Engineering Simulation (OpenSees) to analyze the cyclic behavior of CFRP-confined damaged and undamaged columns. The results of the numerical models are in good agreement with the experiments.

• Earthquakes and Structures
• /
• 제17권2호
• /
• pp.205-219
• /
• 2019

In Peru, construction of dwellings using confined masonry walls (CM) has a high percentage of acceptance within many sectors of the population. It is estimated that only in Lima, 80% of the constructions use CM and at least 70% of these are informal constructions. This mean that they are built without proper technical advice and generally have a high seismic vulnerability. One way to reduce this vulnerability is by reinforcing the walls. However, despite the existence of some reinforcement methods in the market, not all of them can be applied massively because there are other parameters to take into account, as economical, criteria for seismic improvement, reinforcement ratio, etc. Therefore, in this paper the feasibility of using five reinforcement techniques has been studied and compared. These reinforcements are: welded mesh (WM), glass fiber reinforced polymer (GFRP), carbon fiber reinforced polymer (CFRP), steel bar wire mesh (CSM), steel reinforced grout (SRG). The Multi-Criteria Decision Making (MCDM) method can be useful to evaluate the most optimal strengthening technique for a fast, effective and massive use plan in Peru. The results of using MCDM with 10 criteria indicate that the Carbon Fiber Reinforced Polymer (CFRP) and Steel Reinforced Grout (SRG) methods are the most suitable for a massive reinforcement application in Lima.

• Elastomers and Composites
• /
• 제48권2호
• /
• pp.133-140
• /
• 2013

탄소섬유강화 고분자(CFRP) 복합재료는 고분자 매트릭스 내에 탄소섬유를 강화제로 사용한 복합재료이다. 최근 고온 및 고진공 조건이 요구되는 항공우주 및 전자산업용 고성능 재료로 사용하기 위해 높은 열안정성과 낮은 기체방출 특성을 갖는 CFRP 복합재료가 활용되고 있다. 이러한 용도에 시아네이트 에스터 수지는 가장 적합한 매트릭스 수지로 꼽히고 있다. 본 연구에서는 시아네이트 에스터 수지와 촉매의 조합, 경화 거동 및 경화 사이클을 최적화하기 위해 화학유변학적 거동을 분석하였다. 최적 조건은 촉매 100 ppm을 첨가한 수지 조성물을 $150^{\circ}C$에서 경화한 경우로 나타났다. 열안정성과 기체방출 특성을 분석한 결과 경화된 수지 조성물은 열분해 온도 $385^{\circ}C$ 및 전체질량손실 0.29%를 나타내었다. 설정한 수지 조성 및 경화 조건을 사용하여 CFRP 프리프레그 및 이를 적층한 복합재료를 제조하였다. 복합재료의 인장 탄성률을 이론적 모델과 비교한 결과 매우 일관성이 있었다.

• Steel and Composite Structures
• /
• 제23권4호
• /
• pp.385-397
• /
• 2017

Currently, CFRP (Carbon Fiber Reinforced Polymer) plate bonding is used quite extensively as a strengthening method. In this technique, a composite CFRP plate or sheet of relatively small thickness is bonded with an adhesion material to steel or concrete structure in order to improve its structural behavior and strength. The sheets or plates do not require much space and give a composite action between the adherents. In this study, the rotation capacity of CFRP-strengthened cold-formed steel (CFS) beams has been evaluated through numerical investigation. Studies on different structural levels have been performed. At the beam level, C-section has been adopted with different values of profile thickness, web height, and flange width. At the connection level, a web bolted moment resistant type of connection using through plate has been adopted. In web-bolted connections without CFRP strengthening, premature web buckling results in early loss of strength. Hence, CFRP sheets and plates with different mechanical properties and geometric configurations have been examined to delay web and flange buckling and to produce relatively high moment strength and rotation capacity. The numerical results reveal that CFRP strengthening may increase strength, initial stiffness, and rotation capacity when compared with the case without strengthening.